/// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-

#include <AP_HAL/AP_HAL.h>

#if CONFIG_HAL_BOARD == HAL_BOARD_VRBRAIN
#include "UARTDriver.h"

#include <stdio.h>
#include <unistd.h>
#include <stdlib.h>
#include <errno.h>
#include <sys/ioctl.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
#include <termios.h>
#include <drivers/drv_hrt.h>
#include <assert.h>
#include <AP_HAL/utility/RingBuffer.h>

using namespace VRBRAIN;

extern const AP_HAL::HAL& hal;

VRBRAINUARTDriver::VRBRAINUARTDriver(const char *devpath, const char *perf_name) :
	_devpath(devpath),
    _fd(-1),
    _baudrate(57600),
    _initialised(false),
    _in_timer(false),
    _perf_uart(perf_alloc(PC_ELAPSED, perf_name)),
    _os_start_auto_space(-1),
    _flow_control(FLOW_CONTROL_DISABLE)
{
}


extern const AP_HAL::HAL& hal;

/*
  this UART driver maps to a serial device in /dev
 */

void VRBRAINUARTDriver::begin(uint32_t b, uint16_t rxS, uint16_t txS)
{
    if (strcmp(_devpath, "/dev/null") == 0) {
        // leave uninitialised
        return;
    }

    uint16_t min_tx_buffer = 1024;
    uint16_t min_rx_buffer = 512;
    if (strcmp(_devpath, "/dev/ttyACM0") == 0) {
        min_tx_buffer = 16384;
        min_rx_buffer = 1024;
    }
    // on VRBRAIN we have enough memory to have a larger transmit and
    // receive buffer for all ports. This means we don't get delays
    // while waiting to write GPS config packets
    if (txS < min_tx_buffer) {
        txS = min_tx_buffer;
    }
    if (rxS < min_rx_buffer) {
        rxS = min_rx_buffer;
    }

    /*
      allocate the read buffer
      we allocate buffers before we successfully open the device as we
      want to allocate in the early stages of boot, and cause minimum
      thrashing of the heap once we are up. The ttyACM0 driver may not
      connect for some time after boot
     */
	if (rxS != 0 && rxS != _readbuf_size) {
        _initialised = false;
        while (_in_timer) {
            hal.scheduler->delay(1);
        }
		_readbuf_size = rxS;
		if (_readbuf != NULL) {
			free(_readbuf);
		}
		_readbuf = (uint8_t *)malloc(_readbuf_size);
		_readbuf_head = 0;
		_readbuf_tail = 0;
	}

    if (b != 0) {
        _baudrate = b;
    }

    /*
      allocate the write buffer
     */
	if (txS != 0 && txS != _writebuf_size) {
        _initialised = false;
        while (_in_timer) {
            hal.scheduler->delay(1);
        }
		_writebuf_size = txS;
		if (_writebuf != NULL) {
			free(_writebuf);
		}
		_writebuf = (uint8_t *)malloc(_writebuf_size+16);
		_writebuf_head = 0;
		_writebuf_tail = 0;
	}

	if (_fd == -1) {
        _fd = open(_devpath, O_RDWR);
		if (_fd == -1) {
			return;
		}
	}

	if (_baudrate != 0) {
		// set the baud rate
		struct termios t;
		tcgetattr(_fd, &t);
		cfsetspeed(&t, _baudrate);
		// disable LF -> CR/LF
		t.c_oflag &= ~ONLCR;
		tcsetattr(_fd, TCSANOW, &t);

        // separately setup IFLOW if we can. We do this as a 2nd call
        // as if the port has no RTS pin then the tcsetattr() call
        // will fail, and if done as one call then it would fail to
        // set the baudrate.
		tcgetattr(_fd, &t);
		t.c_cflag |= CRTS_IFLOW;
		tcsetattr(_fd, TCSANOW, &t);
	}

    if (_writebuf_size != 0 && _readbuf_size != 0 && _fd != -1) {
        if (!_initialised) {
            ::printf("initialised %s OK %u %u\n", _devpath, 
                     (unsigned)_writebuf_size, (unsigned)_readbuf_size);
        }
        _initialised = true;
    }
}

void VRBRAINUARTDriver::set_flow_control(enum flow_control flow_control)
{
	if (_fd == -1) {
        return;
    }
    struct termios t;
    tcgetattr(_fd, &t);
    // we already enabled CRTS_IFLOW above, just enable output flow control
    if (flow_control != FLOW_CONTROL_DISABLE) {
        t.c_cflag |= CRTSCTS;
    } else {
        t.c_cflag &= ~CRTSCTS;
    }
    tcsetattr(_fd, TCSANOW, &t);
    if (fcontrol == FLOW_CONTROL_AUTO) {
        // reset flow control auto state machine
        _total_written = 0;
        _first_write_time = 0;
    }
    _flow_control = flow_control;
}

void VRBRAINUARTDriver::begin(uint32_t b)
{
	begin(b, 0, 0);
}


/*
  try to initialise the UART. This is used to cope with the way NuttX
  handles /dev/ttyACM0 (the USB port). The port appears in /dev on
  boot, but cannot be opened until a USB cable is connected and the
  host starts the CDCACM communication.
 */
void VRBRAINUARTDriver::try_initialise(void)
{
    if (_initialised) {
        return;
    }
    if ((AP_HAL::millis() - _last_initialise_attempt_ms) < 2000) {
        return;
    }
    _last_initialise_attempt_ms = AP_HAL::millis();
    if (hal.util->safety_switch_state() != AP_HAL::Util::SAFETY_ARMED || !hal.util->get_soft_armed()) {
        begin(0);
    }
}


void VRBRAINUARTDriver::end()
{
    _initialised = false;
    while (_in_timer) hal.scheduler->delay(1);
    if (_fd != -1) {
        close(_fd);
        _fd = -1;
    }
    if (_readbuf) {
        free(_readbuf);
        _readbuf = NULL;
    }
    if (_writebuf) {
        free(_writebuf);
        _writebuf = NULL;
    }
    _readbuf_size = _writebuf_size = 0;
    _writebuf_head = 0;
    _writebuf_tail = 0;
    _readbuf_head = 0;
    _readbuf_tail = 0;
}

void VRBRAINUARTDriver::flush() {}

bool VRBRAINUARTDriver::is_initialized()
{ 
    try_initialise();
    return _initialised; 
}

void VRBRAINUARTDriver::set_blocking_writes(bool blocking)
{
    _nonblocking_writes = !blocking;
}

bool VRBRAINUARTDriver::tx_pending() { return false; }

/*
  return number of bytes available to be read from the buffer
 */
int16_t VRBRAINUARTDriver::available()
{ 
	if (!_initialised) {
        try_initialise();
		return 0;
	}
    uint16_t _tail;
    return BUF_AVAILABLE(_readbuf);
}

/*
  return number of bytes that can be added to the write buffer
 */
int16_t VRBRAINUARTDriver::txspace()
{ 
	if (!_initialised) {
        try_initialise();
		return 0;
	}
    uint16_t _head;
    return BUF_SPACE(_writebuf);
}

/*
  read one byte from the read buffer
 */
int16_t VRBRAINUARTDriver::read()
{ 
	uint8_t c;
    if (!_initialised) {
        try_initialise();
        return -1;
    }
	if (_readbuf == NULL) {
		return -1;
	}
    if (BUF_EMPTY(_readbuf)) {
        return -1;
    }
    c = _readbuf[_readbuf_head];
    BUF_ADVANCEHEAD(_readbuf, 1);
	return c;
}

/* 
   write one byte to the buffer
 */
size_t VRBRAINUARTDriver::write(uint8_t c)
{ 
    if (!_initialised) {
        try_initialise();
        return 0;
    }
    if (hal.scheduler->in_timerprocess()) {
        // not allowed from timers
        return 0;
    }
    uint16_t _head;

    while (BUF_SPACE(_writebuf) == 0) {
        if (_nonblocking_writes) {
            return 0;
        }
        hal.scheduler->delay(1);
    }
    _writebuf[_writebuf_tail] = c;
    BUF_ADVANCETAIL(_writebuf, 1);
    return 1;
}

/*
  write size bytes to the write buffer
 */
size_t VRBRAINUARTDriver::write(const uint8_t *buffer, size_t size)
{
	if (!_initialised) {
        try_initialise();
		return 0;
	}
    if (hal.scheduler->in_timerprocess()) {
        // not allowed from timers
        return 0;
    }

    if (!_nonblocking_writes) {
        /*
          use the per-byte delay loop in write() above for blocking writes
         */
        size_t ret = 0;
        while (size--) {
            if (write(*buffer++) != 1) break;
            ret++;
        }
        return ret;
    }

    uint16_t _head, space;
    space = BUF_SPACE(_writebuf);
    if (space == 0) {
        return 0;
    }
    if (size > space) {
        size = space;
    }
    if (_writebuf_tail < _head) {
        // perform as single memcpy
        assert(_writebuf_tail+size <= _writebuf_size);
        memcpy(&_writebuf[_writebuf_tail], buffer, size);
        BUF_ADVANCETAIL(_writebuf, size);
        return size;
    }

    // perform as two memcpy calls
    uint16_t n = _writebuf_size - _writebuf_tail;
    if (n > size) n = size;
    assert(_writebuf_tail+n <= _writebuf_size);
    memcpy(&_writebuf[_writebuf_tail], buffer, n);
    BUF_ADVANCETAIL(_writebuf, n);
    buffer += n;
    n = size - n;
    if (n > 0) {
        assert(_writebuf_tail+n <= _writebuf_size);
        memcpy(&_writebuf[_writebuf_tail], buffer, n);
        BUF_ADVANCETAIL(_writebuf, n);
    }        
    return size;
}

/*
  try writing n bytes, handling an unresponsive port
 */
int VRBRAINUARTDriver::_write_fd(const uint8_t *buf, uint16_t n)
{
    int ret = 0;

    // the FIONWRITE check is to cope with broken O_NONBLOCK behaviour
    // in NuttX on ttyACM0

    // FIONWRITE is also used for auto flow control detection
    // Assume output flow control is not working if:
    //     port is configured for auto flow control
    // and this is not the first write since flow control turned on
    // and no data has been removed from the buffer since flow control turned on
    // and more than .5 seconds elapsed after writing a total of > 5 characters
    //
    
    int nwrite = 0;

    if (ioctl(_fd, FIONWRITE, (unsigned long)&nwrite) == 0) {
        if (_flow_control == FLOW_CONTROL_AUTO) {
            if (_first_write_time == 0) {
                if (_total_written == 0) {
                    // save the remaining buffer bytes for comparison next write
                    _os_start_auto_space = nwrite;
                }
            } else {
                if (_os_start_auto_space - nwrite + 1 >= _total_written &&
                    (AP_HAL::micros64() - _first_write_time) > 500*1000UL) {
                    // it doesn't look like hw flow control is working
                    ::printf("disabling flow control on %s _total_written=%u\n", 
                             _devpath, (unsigned)_total_written);
                    set_flow_control(FLOW_CONTROL_DISABLE);
                }
            }
        }
        if (nwrite > n) {
            nwrite = n;
        }
        if (nwrite > 0) {
            ret = ::write(_fd, buf, nwrite);
        }
    }

    if (ret > 0) {
        BUF_ADVANCEHEAD(_writebuf, ret);
        _last_write_time = AP_HAL::micros64();
        _total_written += ret;
        if (! _first_write_time && _total_written > 5) {
            _first_write_time = _last_write_time;
        }
        return ret;
    }

    if (AP_HAL::micros64() - _last_write_time > 2000 &&
        _flow_control == FLOW_CONTROL_DISABLE) {
#if 0
        // this trick is disabled for now, as it sometimes blocks on
        // re-opening the ttyACM0 port, which would cause a crash
        if (AP_HAL::micros64() - _last_write_time > 2000000) {
            // we haven't done a successful write for 2 seconds - try
            // reopening the port        
            _initialised = false;
            ::close(_fd);
            _fd = ::open(_devpath, O_RDWR);
            if (_fd == -1) {
                fprintf(stdout, "Failed to reopen UART device %s - %s\n",
                        _devpath, strerror(errno));
                // leave it uninitialised
                return n;
            }
            
            _last_write_time = AP_HAL::micros64();
            _initialised = true;
        }
#else
        _last_write_time = AP_HAL::micros64();
#endif
        // we haven't done a successful write for 2ms, which means the 
        // port is running at less than 500 bytes/sec. Start
        // discarding bytes, even if this is a blocking port. This
        // prevents the ttyACM0 port blocking startup if the endpoint
        // is not connected
        BUF_ADVANCEHEAD(_writebuf, n);
        return n;
    }
    return ret;
}

/*
  try reading n bytes, handling an unresponsive port
 */
int VRBRAINUARTDriver::_read_fd(uint8_t *buf, uint16_t n)
{
    int ret = 0;

    // the FIONREAD check is to cope with broken O_NONBLOCK behaviour
    // in NuttX on ttyACM0
    int nread = 0;
    if (ioctl(_fd, FIONREAD, (unsigned long)&nread) == 0) {
        if (nread > n) {
            nread = n;
        }
        if (nread > 0) {
            ret = ::read(_fd, buf, nread);
        }
    }
    if (ret > 0) {
        BUF_ADVANCETAIL(_readbuf, ret);
        _total_read += ret;
    }
    return ret;
}


/*
  push any pending bytes to/from the serial port. This is called at
  1kHz in the timer thread. Doing it this way reduces the system call
  overhead in the main task enormously. 
 */
void VRBRAINUARTDriver::_timer_tick(void)
{
    uint16_t n;

    if (!_initialised) return;

    // don't try IO on a disconnected USB port
    if (strcmp(_devpath, "/dev/ttyACM0") == 0 && !hal.gpio->usb_connected()) {
        return;
    }

    _in_timer = true;

    // write any pending bytes
    uint16_t _tail;
    n = BUF_AVAILABLE(_writebuf);
    if (n > 0) {
        uint16_t n1 = _writebuf_size - _writebuf_head;
        perf_begin(_perf_uart);
        if (n1 >= n) {
            // do as a single write
            _write_fd(&_writebuf[_writebuf_head], n);
        } else {
            // split into two writes
            int ret = _write_fd(&_writebuf[_writebuf_head], n1);
            if (ret == n1 && n > n1) {
                _write_fd(&_writebuf[_writebuf_head], n - n1);                
            }
        }
        perf_end(_perf_uart);
    }

    // try to fill the read buffer
    uint16_t _head;
    n = BUF_SPACE(_readbuf);
    if (n > 0) {
        uint16_t n1 = _readbuf_size - _readbuf_tail;
        perf_begin(_perf_uart);
        if (n1 >= n) {
            // one read will do
            assert(_readbuf_tail+n <= _readbuf_size);
            _read_fd(&_readbuf[_readbuf_tail], n);
        } else {
            assert(_readbuf_tail+n1 <= _readbuf_size);
            int ret = _read_fd(&_readbuf[_readbuf_tail], n1);
            if (ret == n1 && n > n1) {
                assert(_readbuf_tail+(n-n1) <= _readbuf_size);
                _read_fd(&_readbuf[_readbuf_tail], n - n1);                
            }
        }
        perf_end(_perf_uart);
    }

    _in_timer = false;
}

#endif // CONFIG_HAL_BOARD