// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*- #ifndef PARAMETERS_H #define PARAMETERS_H #include // Global parameter class. // class Parameters { public: // The version of the layout as described by the parameter enum. // // When changing the parameter enum in an incompatible fashion, this // value should be incremented by one. // // The increment will prevent old parameters from being used incorrectly // by newer code. // static const uint16_t k_format_version = 118; // The parameter software_type is set up solely for ground station use // and identifies the software type (eg ArduPilotMega versus ArduCopterMega) // GCS will interpret values 0-9 as ArduPilotMega. Developers may use // values within that range to identify different branches. // static const uint16_t k_software_type = 10; // 0 for APM trunk // Parameter identities. // // The enumeration defined here is used to ensure that every parameter // or parameter group has a unique ID number. This number is used by // AP_Var to store and locate parameters in EEPROM. // // Note that entries without a number are assigned the next number after // the entry preceding them. When adding new entries, ensure that they // don't overlap. // // Try to group related variables together, and assign them a set // range in the enumeration. Place these groups in numerical order // at the end of the enumeration. // // WARNING: Care should be taken when editing this enumeration as the // AP_Var load/save code depends on the values here to identify // variables saved in EEPROM. // // enum { // Layout version number, always key zero. // k_param_format_version = 0, k_param_software_type, // simulation k_param_sitl = 10, // Misc // k_param_log_bitmask = 20, k_param_log_last_filenumber, // *** Deprecated - remove with next eeprom number change k_param_toy_yaw_rate, // THOR The memory location for the Yaw Rate 1 = fast, 2 = med, 3 = slow // // 80: Heli // k_param_heli_servo_1 = 80, k_param_heli_servo_2, k_param_heli_servo_3, k_param_heli_servo_4, // // 90: Motors // k_param_motors = 90, // 110: Telemetry control // k_param_gcs0 = 110, k_param_gcs3, k_param_sysid_this_mav, k_param_sysid_my_gcs, k_param_serial3_baud, // // 140: Sensor parameters // k_param_imu = 140, // sensor calibration k_param_battery_monitoring, k_param_volt_div_ratio, k_param_curr_amp_per_volt, k_param_input_voltage, k_param_pack_capacity, k_param_compass_enabled, k_param_compass, k_param_sonar_enabled, k_param_frame_orientation, k_param_optflow_enabled, k_param_low_voltage, k_param_ch7_option, k_param_auto_slew_rate, k_param_sonar_type, k_param_super_simple, k_param_rtl_land_enabled, // Depricated!! k_param_axis_enabled, k_param_copter_leds_mode, //158 k_param_ahrs, // AHRS group // // 160: Navigation parameters // k_param_RTL_altitude = 160, k_param_crosstrack_gain, k_param_auto_land_timeout, k_param_rtl_approach_alt, k_param_tilt_comp, //164 // // Camera parameters // k_param_camera, // // 170: Radio settings // k_param_rc_1 = 170, k_param_rc_2, k_param_rc_3, k_param_rc_4, k_param_rc_5, k_param_rc_6, k_param_rc_7, k_param_rc_8, k_param_rc_9, k_param_rc_10, k_param_throttle_min, k_param_throttle_max, k_param_throttle_fs_enabled, k_param_throttle_fs_action, k_param_throttle_fs_value, k_param_throttle_cruise, k_param_esc_calibrate, k_param_radio_tuning, k_param_radio_tuning_high, k_param_radio_tuning_low, k_param_camera_pitch_gain, k_param_camera_roll_gain, k_param_rc_speed, k_param_camera_pitch_continuous, k_param_camera_roll_continuous, // // 200: flight modes // k_param_flight_mode1 = 200, k_param_flight_mode2, k_param_flight_mode3, k_param_flight_mode4, k_param_flight_mode5, k_param_flight_mode6, k_param_simple_modes, // // 210: Waypoint data // k_param_waypoint_mode = 210, // remove k_param_command_total, k_param_command_index, k_param_command_nav_index, k_param_waypoint_radius, k_param_loiter_radius, k_param_waypoint_speed_max, // // 220: PI/D Controllers // k_param_stabilize_d_schedule = 219, k_param_stabilize_d = 220, k_param_acro_p, k_param_axis_lock_p, k_param_pid_rate_roll, k_param_pid_rate_pitch, k_param_pid_rate_yaw, k_param_pi_stabilize_roll, k_param_pi_stabilize_pitch, k_param_pi_stabilize_yaw, k_param_pi_loiter_lat, k_param_pi_loiter_lon, k_param_pid_loiter_rate_lat, k_param_pid_loiter_rate_lon, k_param_pid_nav_lat, k_param_pid_nav_lon, k_param_pi_alt_hold, k_param_pid_throttle, k_param_pid_optflow_roll, k_param_pid_optflow_pitch, // 254,255: reserved }; AP_Int16 format_version; AP_Int8 software_type; // Telemetry control // AP_Int16 sysid_this_mav; AP_Int16 sysid_my_gcs; AP_Int8 serial3_baud; AP_Int16 RTL_altitude; AP_Int8 sonar_enabled; AP_Int8 sonar_type; // 0 = XL, 1 = LV, // 2 = XLL (XL with 10m range) // 3 = HRLV AP_Int8 battery_monitoring; // 0=disabled, 3=voltage only, 4=voltage and current AP_Float volt_div_ratio; AP_Float curr_amp_per_volt; AP_Float input_voltage; AP_Int16 pack_capacity; // Battery pack capacity less reserve AP_Int8 compass_enabled; AP_Int8 optflow_enabled; AP_Float low_voltage; AP_Int8 super_simple; AP_Int8 rtl_land_enabled; AP_Int16 rtl_approach_alt; AP_Int8 tilt_comp; AP_Int8 axis_enabled; AP_Int8 copter_leds_mode; // Operating mode of LED lighting system // Waypoints // AP_Int8 waypoint_mode; AP_Int8 command_total; AP_Int8 command_index; AP_Int8 command_nav_index; AP_Int16 waypoint_radius; AP_Int16 loiter_radius; AP_Int16 waypoint_speed_max; AP_Float crosstrack_gain; AP_Int32 auto_land_timeout; // Throttle // AP_Int16 throttle_min; AP_Int16 throttle_max; AP_Int8 throttle_fs_enabled; AP_Int8 throttle_fs_action; AP_Int16 throttle_fs_value; AP_Int16 throttle_cruise; // Flight modes // AP_Int8 flight_mode1; AP_Int8 flight_mode2; AP_Int8 flight_mode3; AP_Int8 flight_mode4; AP_Int8 flight_mode5; AP_Int8 flight_mode6; AP_Int8 simple_modes; // Misc // AP_Int16 log_bitmask; AP_Int16 log_last_filenumber; // *** Deprecated - remove with next eeprom number change AP_Int8 toy_yaw_rate; // THOR The Yaw Rate 1 = fast, 2 = med, 3 = slow AP_Int8 esc_calibrate; AP_Int8 radio_tuning; AP_Int16 radio_tuning_high; AP_Int16 radio_tuning_low; AP_Int8 frame_orientation; AP_Int8 ch7_option; AP_Int16 auto_slew_rate; #if FRAME_CONFIG == HELI_FRAME // Heli RC_Channel heli_servo_1, heli_servo_2, heli_servo_3, heli_servo_4; // servos for swash plate and tail #endif // Camera #if CAMERA == ENABLED AP_Camera camera; #endif // RC channels RC_Channel rc_1; RC_Channel rc_2; RC_Channel rc_3; RC_Channel rc_4; RC_Channel_aux rc_5; RC_Channel_aux rc_6; RC_Channel_aux rc_7; RC_Channel_aux rc_8; RC_Channel_aux rc_9; RC_Channel_aux rc_10; AP_Int16 rc_speed; // speed of fast RC Channels in Hz AP_Float camera_pitch_gain; AP_Float camera_roll_gain; AP_Int8 camera_pitch_continuous; AP_Int8 camera_roll_continuous; AP_Float stabilize_d; AP_Float stabilize_d_schedule; // PI/D controllers AP_Float acro_p; AP_Float axis_lock_p; AC_PID pid_rate_roll; AC_PID pid_rate_pitch; AC_PID pid_rate_yaw; AC_PID pid_loiter_rate_lat; AC_PID pid_loiter_rate_lon; AC_PID pid_nav_lat; AC_PID pid_nav_lon; AC_PID pid_throttle; AC_PID pid_optflow_roll; AC_PID pid_optflow_pitch; APM_PI pi_loiter_lat; APM_PI pi_loiter_lon; APM_PI pi_stabilize_roll; APM_PI pi_stabilize_pitch; APM_PI pi_stabilize_yaw; APM_PI pi_alt_hold; // Note: keep initializers here in the same order as they are declared above. Parameters() : // variable default //---------------------------------------- format_version (k_format_version), software_type (k_software_type), sysid_this_mav (MAV_SYSTEM_ID), sysid_my_gcs (255), serial3_baud (SERIAL3_BAUD/1000), RTL_altitude (ALT_HOLD_HOME * 100), sonar_enabled (DISABLED), sonar_type (AP_RANGEFINDER_MAXSONARXL), battery_monitoring (DISABLED), volt_div_ratio (VOLT_DIV_RATIO), curr_amp_per_volt (CURR_AMP_PER_VOLT), input_voltage (INPUT_VOLTAGE), pack_capacity (HIGH_DISCHARGE), compass_enabled (MAGNETOMETER), optflow_enabled (OPTFLOW), low_voltage (LOW_VOLTAGE), super_simple (SUPER_SIMPLE), rtl_land_enabled (0), rtl_approach_alt (RTL_APPROACH_ALT), tilt_comp (54), axis_enabled (AXIS_LOCK_ENABLED), copter_leds_mode (9), waypoint_mode (0), command_total (0), command_index (0), command_nav_index (0), waypoint_radius (WP_RADIUS_DEFAULT), loiter_radius (LOITER_RADIUS), waypoint_speed_max (WAYPOINT_SPEED_MAX), crosstrack_gain (CROSSTRACK_GAIN), auto_land_timeout (AUTO_LAND_TIME * 1000), throttle_min (MINIMUM_THROTTLE), throttle_max (MAXIMUM_THROTTLE), throttle_fs_enabled (THROTTLE_FAILSAFE), throttle_fs_action (THROTTLE_FAILSAFE_ACTION), throttle_fs_value (THROTTLE_FS_VALUE), throttle_cruise (THROTTLE_CRUISE), flight_mode1 (FLIGHT_MODE_1), flight_mode2 (FLIGHT_MODE_2), flight_mode3 (FLIGHT_MODE_3), flight_mode4 (FLIGHT_MODE_4), flight_mode5 (FLIGHT_MODE_5), flight_mode6 (FLIGHT_MODE_6), simple_modes (0), log_bitmask (DEFAULT_LOG_BITMASK), log_last_filenumber (0), toy_yaw_rate (1), // THOR The default Yaw Rate 1 = fast, 2 = med, 3 = slow esc_calibrate (0), radio_tuning (0), radio_tuning_high (1000), radio_tuning_low (0), frame_orientation (FRAME_ORIENTATION), ch7_option (CH7_OPTION), auto_slew_rate (AUTO_SLEW_RATE), rc_speed(RC_FAST_SPEED), camera_pitch_gain (CAM_PITCH_GAIN), camera_roll_gain (CAM_ROLL_GAIN), camera_pitch_continuous (CAM_PITCH_CONTINUOUS), camera_roll_continuous (CAM_ROLL_CONTINUOUS), stabilize_d (STABILIZE_D), stabilize_d_schedule (STABILIZE_D_SCHEDULE), acro_p (ACRO_P), axis_lock_p (AXIS_LOCK_P), // PID controller initial P initial I initial D initial imax //----------------------------------------------------------------------------------------------------- pid_rate_roll (RATE_ROLL_P, RATE_ROLL_I, RATE_ROLL_D, RATE_ROLL_IMAX * 100), pid_rate_pitch (RATE_PITCH_P, RATE_PITCH_I, RATE_PITCH_D, RATE_PITCH_IMAX * 100), pid_rate_yaw (RATE_YAW_P, RATE_YAW_I, RATE_YAW_D, RATE_YAW_IMAX * 100), pid_loiter_rate_lat (LOITER_RATE_P, LOITER_RATE_I, LOITER_RATE_D, LOITER_RATE_IMAX * 100), pid_loiter_rate_lon (LOITER_RATE_P, LOITER_RATE_I, LOITER_RATE_D, LOITER_RATE_IMAX * 100), pid_nav_lat (NAV_P, NAV_I, NAV_D, NAV_IMAX * 100), pid_nav_lon (NAV_P, NAV_I, NAV_D, NAV_IMAX * 100), pid_throttle (THROTTLE_P, THROTTLE_I, THROTTLE_D, THROTTLE_IMAX), pid_optflow_roll (OPTFLOW_ROLL_P, OPTFLOW_ROLL_I, OPTFLOW_ROLL_D, OPTFLOW_IMAX * 100), pid_optflow_pitch (OPTFLOW_PITCH_P, OPTFLOW_PITCH_I, OPTFLOW_PITCH_D, OPTFLOW_IMAX * 100), // PI controller initial P initial I initial imax //---------------------------------------------------------------------- pi_loiter_lat (LOITER_P, LOITER_I, LOITER_IMAX * 100), pi_loiter_lon (LOITER_P, LOITER_I, LOITER_IMAX * 100), pi_stabilize_roll (STABILIZE_ROLL_P, STABILIZE_ROLL_I, STABILIZE_ROLL_IMAX * 100), pi_stabilize_pitch (STABILIZE_PITCH_P, STABILIZE_PITCH_I, STABILIZE_PITCH_IMAX * 100), pi_stabilize_yaw (STABILIZE_YAW_P, STABILIZE_YAW_I, STABILIZE_YAW_IMAX * 100), pi_alt_hold (ALT_HOLD_P, ALT_HOLD_I, ALT_HOLD_IMAX) { } }; #endif // PARAMETERS_H