Jason Short
efdf0a7fc8
changed define to a param for throttle_min and throttle_max
2012-06-20 15:00:53 -07:00
Jason Short
e8510faf5d
changed define to param for throttle_min
2012-06-20 15:00:05 -07:00
Jason Short
6020f6d9fa
Added throttle_min as a user definable param
2012-06-20 14:58:34 -07:00
Jason Short
4f18e7f80b
lowered minimum throttle
2012-06-20 08:47:47 -07:00
Jason Short
27e0aee03f
Small fix to angle boost - increases by about 20% to deal with inefficiencies of non-downward thrust
2012-06-20 08:47:47 -07:00
Jason Short
39a253a273
decreased I term based on the tests last weekend in high winds
2012-06-20 08:47:47 -07:00
Jason Short
8b212d8baa
Adjustments to the Inertial_nav
...
lowered Rate_I and Rate_P to be less jumpy. raised throttle_p
added a clear to rate when entering loiter
moved the raw reporting
2012-06-20 08:47:47 -07:00
Andrew Tridgell
58379b928f
MAVLink: make usage of MAVLink defines more consistent
2012-06-15 16:27:11 +10:00
rmackay9
c62cc4844e
ArduCopter: updated firmware to simply 2.6 (i.e. removed Epsilon) ahead of the release
2012-06-15 00:42:59 +09:00
Jason Short
e31a1d969f
Inertial Nav disabled by default
2012-06-13 22:37:52 -07:00
Jason Short
c42f9ece43
Inertial Control
...
I added inertial navigation based on the simulator data. This is an option only available if you compile with Arduino and set
#define INERTIAL_NAV ENABLED
in the APM_Config.h file.
This has been tested for one real flight and did not crash my quad, but consider it very alpha. The quad may be unpredictable at first until the error correction fixes poorly calibrated accels. Be Careful.
Most of the real work is in the inertia file, but the error correction, new variable defines and calibration calls are sprinkled throughout.
The Log should record RAW messages with special debugging values.
2012-06-13 22:34:45 -07:00
rmackay9
65050775e1
ArduCopter: made Robert's new yaw method optional (off by default).
...
Add this line to APM_Config.h to enable Robert's yaw
#define ALTERNATIVE_YAW_MODE ENABLED
2012-06-13 21:50:16 +09:00
Jason Short
ff0659535e
Raised the Max throttle to 1000, min to 200. Worked good in SIM with Tridge's motor safety patch.
2012-06-12 13:58:49 -07:00
rmackay9
e1acf21381
ArduCopter: updated firmware version to 2.6 Epsilon
2012-06-12 23:22:57 +09:00
rmackay9
c6f1d93849
ArduCopter: updated standard loiter pids.
...
Loiter_P (speed from distance to target) = 0.2 (was 0.35)
Loiter_Rate_P (lean angle from desired acceleration) = 2.4 (was 2.5)
Loiter_Rate_I = unchanged at 0.08
Loiter_Rate_D = 0.40 (was 0.45)
2012-06-12 20:56:31 +09:00
Jason Short
f5a85d48a0
Added Angel's name to contrib list
2012-06-10 12:38:22 -07:00
Andrew Tridgell
940d994efb
GPS: Use appropiate GPS_ENGINE settings in APM, ACM and rover
2012-06-10 16:36:18 +10:00
rmackay9
aeaebb21d5
ArduCopter: updated firmware version to 2.6 Delta ahead of the next round of testing (and hopefully soon a release)
2012-06-08 21:54:09 +09:00
Andrew Tridgell
a684bddbda
GPS: open the GPS serial port with a 256 byte buffer
...
the UBLOX needs more than 128 bytes for reliable parsing
2012-06-08 16:42:03 +10:00
Robert Lefebvre
c5916a8b4d
Opening up the Yaw Rate constraint for Trad Heli.
2012-06-07 22:40:25 -04:00
Robert Lefebvre
e2496181ff
Yaw Fix
...
Modified Nav_Yaw controller to better track intended heading changes.
2012-06-07 17:15:33 -04:00
Jason Short
a9610a0761
Stabilization patches
...
removed Angle error limit for stabilization
constricted Iterm to +- 5° error and limited the implementation to when the quad is +- 5° from center
doubled the output limit for Rate controller.
increased default Rate_P gain to .18 with matching Rate_D of .004
Tested in the SIM and in backyard. dramatically increases performance and quad no longer overshoots and flips when pushed hard.
2012-06-05 16:41:44 -07:00
rmackay9
70b04d9427
ArduCopter: updated firmware description to 2.6 Gamma
2012-06-05 21:28:13 +09:00
Andrew Tridgell
8b258e23e7
ACM: prevent link flood with "Low Battery" warnings
...
thanks to Marco for noticing this
2012-06-05 11:31:40 +10:00
Michael Oborne
14be88dd55
AC: add hilstate message
2012-06-04 16:24:08 +08:00
Jason Short
71f80f3a77
Bug fix: When adjusting altitude, RTL then land will fail unless this var is reset to false.
2012-06-03 22:25:27 -07:00
Jason Short
1b9f75c844
Updates to Flip:
...
Ability to abort flip mode if things go wrong
init function to re-enter flip mode if aborted
2012-06-03 22:15:19 -07:00
Andrew Tridgell
7c63d2c17b
ACM: MAVLINK10 uses HIL_STATE
...
thanks to Michael for noticing this
2012-06-04 13:31:07 +10:00
Andrew Tridgell
e7cf643386
added mavlink09 targets
...
allows easier building with mavlink0.9
2012-06-04 13:14:52 +10:00
Andrew Tridgell
3f4e87cccc
ACM: fixed HIL build for MAVLINK10
2012-06-04 13:14:52 +10:00
Michael Oborne
9303a89573
fix AC hil build
2012-06-04 11:12:52 +08:00
Michael Oborne
a71ed6c5ce
enable mavlink10 by default
2012-06-04 08:02:08 +08:00
Jason Short
15aea320cb
Added note to remove this unused param
2012-06-03 11:13:50 -07:00
Jason Short
12ab875d58
using current PWM rather than a re-read of the PWM.
2012-06-03 11:13:50 -07:00
Jason Short
9ab06c5542
Moved PID logging counter into define
2012-06-03 11:13:50 -07:00
rmackay9
72d76558a7
ArduCopter: Ensure update_GPS does nothing when gps is disabled.
...
This fixes a bug in which an APM without a GPS would not work because it would constantly scan for a valid GPS long after it should have given up and moved on.
2012-06-03 23:48:45 +09:00
rmackay9
fd6b21d0c7
ArduCopter: updated firmware version to 2.6Beta in preparation for beginning of testing
2012-06-03 17:02:35 +09:00
rmackay9
4544b37fec
ArduCopter: updated firmware version to 2.6Beta in preparation for beginning of testing
2012-06-03 16:59:23 +09:00
rmackay9
dcdeae412e
ArduCopter: Another attempt at fixing the lat/lon printing bug in which small negative lattitudes or longitudes were appearing as positives.
...
Fixed in both ArduCopter Log.pde and the GPS Auto test sketch
2012-06-03 16:58:19 +09:00
rmackay9
2a216ce900
ArduCopter: fixed print_latlon bug in which it would print negative lat/lon numbers incorrectly (i.e. -1234567890 would be printed as -124.xxx).
2012-06-02 12:51:12 +09:00
Jason Short
c2d14a5cad
RC_Channel fix for throttle output.
...
throttle was outputting incorrectly and allowing the user to max out the throttle leaving nothing for attitude control
2012-05-31 14:59:03 -07:00
Robert Lefebvre
5f058fb9b2
TradHeli: Incorporating Ext ESC Control
2012-05-30 21:50:25 -04:00
Robert Lefebvre
30e55533dc
Change to increase Parameter space as we have run out.
...
This will decrease the max number of waypoints from 186
to 169.
2012-05-30 20:41:53 -04:00
Jason Short
dec6f0ca62
When RTLing, force home as the final location for loiter.
2012-05-30 11:06:41 -07:00
Jason Short
bc578172a5
moved detector to run until the throttle is low, then stop running.
2012-05-30 09:44:59 -07:00
Jason Short
f0456dc947
Missed a Semicolon
2012-05-30 09:36:16 -07:00
Jason Short
302c632205
Altered the ground detector logic to no continuously run when landed
2012-05-30 09:34:31 -07:00
Jason Short
22065e3f3f
Broken timer - removed
2012-05-29 12:56:38 -07:00
Jason Short
0ce883b96a
Removed unused variable
2012-05-29 12:43:23 -07:00
Jason Short
9310d613e1
Lowered I term - causes oscillations in SIM
2012-05-29 12:43:01 -07:00
Jason Short
2311d52d37
Renamed some variables to clarify functionality.
2012-05-29 12:42:37 -07:00
Jason Short
7c6f766251
Speed up automatic disarming to 25 seconds for safety.
...
renamed AUTO_ARMING_DELAY to AUTO_DISARMING_DELAY
2012-05-29 12:41:35 -07:00
Jason Short
f491f5e9ca
Removed references to a takeoff timer
2012-05-29 11:28:40 -07:00
Jason Short
15774366ba
Failsafe: Looking for takeoff_complete now vs unreliable GPS
2012-05-29 11:25:04 -07:00
Jason Short
08bf04dd08
pulling throttle low in flight turns out to be more common than thought. Removed clearing of takeoff_complete flag. This is still cleared during disarm which is automatic after 30 seconds of no throttle.
2012-05-29 11:25:04 -07:00
Jason Short
09f4a16bfb
changed the way takeoff complete is figured. Looking for high throttle.
2012-05-29 11:25:04 -07:00
Jason Short
b8349f5486
Added note to functionality
2012-05-29 11:25:04 -07:00
Jason Short
9d92602188
changed WP radius to AP_Int16
2012-05-28 22:39:29 -07:00
Jason Short
5754f97433
reversed circle_WP calculation so the next_WP refers to the destination around the circle and circle_WP refers to the center. The intent is to make it easier to see via ground station.
2012-05-27 09:21:20 -07:00
Jason Short
7df1aa2914
Arducopter.pde : setting rtl_approach_alt above 1 would force auto landing even if auto-landing was disabled.
2012-05-23 22:00:56 -07:00
Andrew Tridgell
d9457ecc38
MAVLink: send time of GPS fix accurately
...
when we send a GPS_RAW message, set the usec field to the time we got
the fix from the GPS, not the current time. This makes it possible for
aerial photo processing to be more accurate, as the usec field with
more accurately reflect the planes position/time pair
2012-05-23 17:33:33 +10:00
Andrew Tridgell
66544a5db2
Log: don't print '+' while erasing logs
...
we no longer do page based erase, so printing a + every 128 pages
makes no sense
2012-05-22 20:10:29 -07:00
Robert Lefebvre
4e4ff84cf1
Updates to CopterLEDS
...
Creation of Nav Blink Function.
2012-05-22 09:58:37 -04:00
Andrew Tridgell
422dc82f32
MAVLink: allow parameter fetch during mavlink_delay()
...
this allows the planner to fully connect to the APM with MAVLink while
doing a DataFlash erase
2012-05-22 16:13:35 +10:00
Jason Short
1b9f34e4e0
Flip.pde: renamed dcm to ahrs
2012-05-21 12:58:51 -07:00
Jason Short
5407acdb4c
Some bug fixes to Auto-flip. I ran this code through the sim and found these flaws.
2012-05-21 11:07:41 -07:00
Jason Short
f6d8a18182
Added note
2012-05-21 09:58:23 -07:00
Jason Short
1a5e2f4e37
Attitude.pde - Removed rate limit based on SIM flights. These should never have been in place and seriously detriment Acro flight.
2012-05-21 09:58:23 -07:00
Jason Short
8d075015e1
added check for duplicate time-stamped GPS messages.
2012-05-18 09:54:18 -07:00
Jason Short
9732b7d2dc
navigation.pde:
...
removed unneeded WP_Distance check
remove unneeded return for Navigate
removed unneeded rate_D calcs
removed unused functions
2012-05-17 11:05:05 -07:00
Jason Short
7e190c6f5c
Arducopter.pde :
...
removed unneeded d_rate_filters
updated Nav routine to handle faster GPS updates
moved calc_XY_velocity to GPS read
added check for duplicate GPS reads
2012-05-17 11:05:05 -07:00
Jason Short
d1cd04486a
removed retro loiter code since Angel has a branch now.
...
shrank speed filter to avoid latency
removed unused forward estimator code
placed code for switchover to gps.groundspeed at 1.5m/s
added clamp for D term when below .5m/s to eliminate noise
added hybrid I-term based on speed error and position
changes Loiter D term to use position rather than acceleration to avoid noise
2012-05-15 22:14:23 -07:00
Jason Short
7f3e142fa8
Loiter Gains based on new SIM
2012-05-15 22:01:01 -07:00
Robert Lefebvre
c5f7b2fff2
Fixed Syntax error.
2012-05-15 12:35:35 -04:00
Robert Lefebvre
c8fb9a6635
More CopterLEDS changes.
...
Merged CopterLEDS and Piezo functions to eliminate pin conflict on APM2. Created new Parameter bit to turn piezo function on and off from MP. Moved GPS and Aux pin assignments to allow commonality between APM1 and 2. Set LED_Mode parameter default to 9 in order to make CopterLEDS completely backwards compatible with old Motor LEDS and Piezo code. Legacy users should see no difference.
2012-05-15 12:00:21 -04:00
Robert Lefebvre
a285e2779f
CopterLEDS changes for APM2
2012-05-15 10:07:03 -04:00
rmackay9
357d6c2d9b
ArduCopter: bug fix for reversing tri servo
...
Extended AP_MotorsTri class to take in pointer to rc_tail servo (rc_7) and we use this servo's REV parameter to determine whether to reverse the output to the tail servo or not
2012-05-13 12:36:46 +09:00
rmackay9
2f74004fcb
ArduCopter: updated version to 2.5.5
2012-05-13 08:47:43 +09:00
rmackay9
af86ae8cbf
ArduCopter: fixed compile error by declaring extern print_latlon
2012-04-30 21:44:27 +09:00
Andrew Tridgell
435a64b97e
ACM: fixed HIL build
2012-04-30 22:42:17 +10:00
rmackay9
a1f5661161
ArduCopter: restored gps test in CLI
...
Added check so not enabled when using 1280. Also fixed comments in other tests to explain the check for the 1280.
2012-04-30 17:29:50 +09:00
Adam M Rivera
56d3fa1601
Parameters.pde/AP_MotorsHeli: Updated comments to leverage the new value aliases
2012-04-28 20:50:41 -05:00
Adam M Rivera
40fdba441b
Parameters.pde: Added value aliases to comments
2012-04-28 20:35:22 -05:00
Adam M Rivera
941cf6fa69
Parameters.pde: Added more parameter comments.
2012-04-28 12:14:17 -05:00
Andrew Tridgell
67afdc7485
autotest: fixes for MAVLink 1.0 in autotest
2012-04-27 15:15:53 +10:00
Adam M Rivera
239323eaa4
Parameters.pde/AP_MotorsHeli.cpp: Added comments from Roberts clone.
2012-04-26 18:26:14 -05:00
Adam M Rivera
cb6f97fc7f
Changed the marker for Group parameters to @Group.
2012-04-25 12:27:51 -05:00
Adam M Rivera
51bcc73c77
Parameters.pde: Added lib comments.
2012-04-25 11:23:46 -05:00
Adam M Rivera
9fb9231ec4
Merge branch 'master' of https://code.google.com/p/ardupilot-mega into param-suffix
2012-04-24 14:11:54 -05:00
Adam M Rivera
29fec278eb
Parameters.pde: Updated comment schema to include the parameter name which becomes the XML node that contains the meta data.
2012-04-24 13:11:16 -05:00
Adam M Rivera
acab9b7c2c
Parameters.pde: Added new comment structure to a few parameters for testing.
2012-04-24 11:37:33 -05:00
Andrew Tridgell
4fee26437b
MAVLink: make ACM build with MAVLink 1.0 possible in arduino GUI
2012-04-24 22:24:58 +10:00
Andrew Tridgell
fe970221e2
ACM: added support for MAVLink 1.0 to ArduCopter
...
most operations should now work
2012-04-24 19:54:20 +10:00
Adam M Rivera
b2a7227ae7
ArduCopter/Navigation: Updated code to reference the new g.retro_loiter param instead of the compile define.
2012-04-23 00:19:18 -05:00
Adam M Rivera
60c347e23b
Parameters: Added g.retro_loiter which is configurable by the user via the MP.
2012-04-23 00:17:52 -05:00
Adam M Rivera
8e580729b7
config.h: Removed comment.
2012-04-23 00:16:41 -05:00
Adam M Rivera
97040a7b3a
Merge branch 'master' of https://code.google.com/p/ardupilot-mega into auto-approach
2012-04-23 00:03:37 -05:00
Jason Short
9c19138fb8
Log.pde : Updated Flash Logging to log Floats properly vs scaled integers.
2012-04-21 15:25:53 -07:00
Jason Short
e22832a832
Added a union for casting floats to ints and back when storing Floats to the DataFlash
2012-04-21 15:17:09 -07:00
rmackay9
090f5aaa6f
ArduCopter - config.h - set standard RC_SPEED to 125 for helicopter frame
2012-04-21 23:46:36 +09:00