aefb38e486
Copter: remove param to disable accel based throttle controller
2013-07-12 22:57:30 +09:00
404cd5f3da
Copter: rename g.pid_throttle to g.pid_throttle_rate
...
Small code clean-up to make throttle rate controller's pid more obvious
2013-06-30 00:04:21 -10:00
23eade8f74
Copter: enable RELAY_* parameters
2013-06-25 12:46:53 +10:00
213eaa8db6
Copter: integrate draft RCMapper
2013-06-03 16:23:47 +10:00
5ee68db6f0
TradHeli: add parameter descriptions
...
small formatting changes too
2013-05-21 15:33:41 +09:00
bd44c2f73d
Copter: all pre-arm checks to be disabled
...
set ARMING_CHECK parameter to zero to disable
2013-05-20 14:48:04 +09:00
9fdab5e8fe
Copter: remove unused AUTO_SLEW_RATE parameter
2013-05-17 16:09:17 +09:00
38239c652a
Copter: ch8 aux switch
...
Ch8 can be used as an aux switch like ch7. Has all the same options as
ch7 and there is a safety check to ensure both switches aren't set to
the same function so as to avoid interfering with each other
2013-05-17 14:42:28 +09:00
bab9fa25e5
Copter: add GCS failsafe
2013-04-29 21:30:22 +09:00
c232d7af4b
Copter: correct fence parameter
2013-04-27 11:14:11 +09:00
58d1da2d80
Copter: integrate AC_Fence in place of limits
...
Lesser functionality than limits but saves more than 150 bytes and it
works
2013-04-27 11:14:07 +09:00
300a8d2bbc
Copter: support all 12 channels on PX4
...
last 4 channels are on the FMU pins
2013-04-25 20:10:53 +10:00
745df9b13c
Copter: add SONAR_GAIN to tune reaction to sonar
...
Some users report the response to sonar is too violent, this allows that
reaction to be reduced
2013-04-20 15:58:36 +09:00
37abfdc65a
Copter: make CIRCLE_RATE a tunable parameter
...
Also bug fix to check of how many time it has rotated during a loiter
turns mission command
2013-04-20 12:03:55 +09:00
0fc9c8739e
Copter: add WP_YAW_BEHAVE parameter
...
Allows user to control whether nose points towards next waypoint and/or
home when RTLing.
Replaces YAW_OVR_BEHAVE which had a very similar purpose. Almost nobody
ever knew about or used this parameter.
2013-04-18 15:30:18 +09:00
f5955d8915
Copter: auto climb and descent params removed
...
These params now reside in the AC_WPNav library
2013-04-18 14:52:21 +09:00
629d23b7e2
Copter: remove WP_SPEED and WP_RADIUS parameters
...
AC_WPNav library has equivalent params with very similar names
2013-04-14 13:27:37 +09:00
b58c26bcd5
Copter: remove pid_nav_lat, pid_nav_lon
2013-04-14 12:12:51 +09:00
2db8365c90
Copter: add AC_WPNav to parameters list
2013-04-14 10:39:02 +09:00
1b6fcad90a
Copter: remove tilt compensation parameter
...
Note: this idea of feed forward tilt compensation is being incorporated
into the inertial nav based loiter and wp controllers but does not
require a separate tunable parameter
2013-03-17 16:53:32 +09:00
61e29173e3
Copter: remove unused crosstrack variables and parameters
...
Cross track is still calculated internally to the wpnav controller so we
should move this to a library and still report it to the ground station
2013-03-17 16:46:31 +09:00
150046f2b8
Copter: GPS Failsafe implemented
...
Switches to LAND mode 5 seconds after losing GPS if you're in a flight
mode that requires a GPS
2013-03-16 17:27:46 +09:00
33bd984a91
Copter: remove unused input_voltage parameter
2013-03-03 23:23:54 +09:00
06a71af12f
Copter: THR_MID used to scale manual throttle
2013-02-01 22:37:16 +09:00
dcb181d2d8
Copter: use new AP_Scheduler library
2013-01-12 12:02:57 +11:00
68b62abd38
ArduCopter with the new Camera and Relay classes for APM1 and APM2.
...
All changes by Sandro Benigno
2013-01-02 09:55:37 +11:00
e850ab7ccd
ArduCopter: add AUTO_VELZ_MIN, AUTO_VELZ_MAX and PILOT_VELZ_MAX to allow better control of climb/descent rate in auto and manual throttle modes
2013-01-02 09:24:31 +11:00
9e986801c9
Copter: fixed SITL for ArduCopter
2012-12-20 14:52:34 +11:00
ada10f6eb2
ArduCopter: change comment references to AP_Var to AP_Param
...
* jsut to clean up the grep for "AP_Var"
2012-12-20 14:51:31 +11:00
2f748f8382
ArduCopter: renamed BATT_FAILSAFE to FS_BATT_ENABLE
2012-12-10 23:47:14 +09:00
d31efebd44
ArduCopter: rename throttle failsafe parameters.
...
Switch to LAND flight mode if throttle failsafe triggers and we do not have a GPS.
THR_FAILSAFE renamed to FS_THR_ENABLE.
THR_FS_VALUE renamed to FS_THR_VALUE.
THR_FS_ACTION removed (action is now controlled by setting FS_THR parameter).
2012-12-10 23:38:43 +09:00
2f1b2b70e6
ArduCopter: added ACRO_TRAINER parameter to allow enabling/disabling the acro training function which will bring the roll back to within +- 45 degrees
2012-12-10 22:27:46 +09:00
dadad8677e
ArduCopter: added descriptions for most parameters that did not have them
...
Renamed loiter_radius to circle_radius to better reflect it's purpose.
Removed some unused parameters including WP_MODE, WP_MUST_INDEX, LOG_LASTFILE, AXIS_P
2012-12-10 21:45:57 +09:00
56ceb230cb
ArduCopter: add YAW_OVR_BEHAVE to allow control of when autopilot takes back control of yaw after pilot overrides it during a mission
2012-12-09 18:04:31 +09:00
39d524212f
ArduCopter: allow accel based throttle controller to be enabled/disabled with the new THR_ACC_ENABLE parameter.
...
When disabled the original velocity based throttle controller is used.
2012-12-06 10:31:57 +09:00
a5bb54e36e
ArduCopter: RTL clean-up and slightly improved landing sensor
...
Consolidated RTL state to be captured by rtl_state variable.
Combined update_RTL_Nav and verify_RTL functions which performed the same function but one was for missions, the other for the RTL flight mode.
Renamed some RTL parameters and global variables to have RTL at the front.
Landing detector now checks accel-throttle's I term and/or a very low throttle value
2012-12-06 10:31:52 +09:00
7b4ed2d227
ArduCopter: restored landing detector to landing throttle mode.
...
Added LAND_SPEED parameter to control the rate of descent for the last 10m of a landing.
Added CH6 tuning for accel based throttle controller.
2012-12-06 10:31:20 +09:00
3cbef57c64
ArduCopter: first merge of leonard's accel based altitude controller plus other changes from Randy
...
Changes include:
New low-level get_throttle_accel function takes target acceleration and compares vs earth-frame Z accelerometer values to produce output to motors.
Higher level throttle controllers modified to call new get_throttle_accel controller
Throttle_rate_stabilized controller added which maintains a desired climb/descent rate
Throttle_land controller added - descends using normal auto throttle controller to 10m then descends at 50cm/s
Multiple throttle modes added including landing mode
Land flight mode no longer needs GPS
Throttle cruise maintenance moved to update_throttle_cruise function
2012-12-06 10:30:49 +09:00
5723021be1
ACM: TradHeli
...
Creating Rate Feed-Forward Parameters
2012-12-04 13:47:38 -05:00
cd07d965a7
Copter: ported RSSI_PIN option from ArduPlane
...
this is useful for OSD users
2012-11-22 20:59:33 +11:00
e92b560df5
ArduCopter: low baterry failsafe
2012-11-15 23:35:41 +09:00
d2a5928c06
Ap state updates
2012-11-09 22:15:15 -08:00
1f801714e8
ArduCopter: incorporate new version of inertial navigation
...
Moved several navigation functions from ArduCopter.pde to navigation.pde
2012-11-07 19:21:31 +09:00
d9b4407e64
AP_InertialSensor: changes after review with Tridge.
...
sanity checking added to accelerometer calibration routine.
user feedback is sent using gcs_send_text_fmt instead of Serial.printf.
moved ins parameters to new eeprom number to avoid conflicts with older parameters.
other small changes including renaming of functions and parameters.
2012-11-07 19:21:15 +09:00
a1b4ec6d0e
ArduCopter: move to use new INS library instead of IMU library
2012-11-07 19:21:09 +09:00
5e8043fd9c
ArduCopter: changed ACRO_ROLL_STABILIZE and ACRO_PITCH_STABILIZE to parameters
...
Changes on behalf of Leonard Hall
2012-10-23 21:30:50 +09:00
4395fad6e9
ArduCopter: incremented eeprom format version to force users to accept the new defaults.
...
Particularly important is the roll-pitch I term move from the stabilize to rate controllers.
2012-10-19 16:14:51 +09:00
4a41a3d210
ArduCopter: added BATT_VOLT_PIN and BATT_CURR_PIN parameters to allow support for new 3DR IV battery voltage and current monitor
2012-10-13 18:40:46 +09:00
ea4f256f8e
ArduCopter: BATT_PIN parameter added to allow you to select which pin is used for voltage and current measurements
...
To save a parameter, the current sensor pin is assumed to always be 1 higher than the voltage pin.
2012-10-02 22:16:19 +09:00
a73bc70553
ACM : Params - formatting cleanup
2012-09-10 20:22:11 -07:00
Randy Mackay
Andrew Tridgell
Pat Hickey
Robert Lefebvre
Jason Short