Fixes code that didn't take into account fall-through behaviour of C++ switch statements
Makes get_rigin furnction more generic allowing the consumer to decide what to do with an invalid origin
If an external gyro calibration has been performed, we should assume that it has been done under static conditions
Otherwise it is pointless and we should allow the EKF to find its own gyro bias offsets.
This patch adds additional methods to the the AHRS library so that the AP_InertialNav library dow nto have to access the EKF directly. This enables Copter to fly using the EKF nominated by AHRS_EKF_TYPE.
It will also pave the way to elimination of the AP_InertialNav library.
This warning happens because of the difference of datatypes between
32 and 64 bits processors.
%% libraries/AP_HAL_Linux/RCInput_UDP.o
/home/zehortigoza/dev/ardupilot/libraries/AP_HAL_Linux/RCInput_UDP.cpp: In member function 'virtual void Linux::LinuxRCInput_UDP::_timer_tick()':
/home/zehortigoza/dev/ardupilot/libraries/AP_HAL_Linux/RCInput_UDP.cpp:42:72: warning: format '%llu' expects argument of type 'long long unsigned int', but argument 3 has type 'uint64_t {aka long unsigned int}' [-Wformat=]
hal.console->printf("no rc cmds received for %llu\n", delay);
As AVR2560 is not supported anymore and do integer operations is
usually faster than float-point the _calculate() implementation was
done using only integer operations and as more close to what
datasheet says.
offset parameter units are milligauss
User settable parameters should have a User category defined. Those that should never be set by a user should not have this.
The function rotate_field() can change the values axes and the function
correct_field() applies offsets (which are already in milligauss). Thus any
sensitivity adjustment must be done for two reasons:
(1) The offsets must be applied to the values already in milligauss;
(2) The factory sensitivity adjustment values are per axis, if any rotation
that switches axes is applied, that'll mess with the adjustment.
Experiments showed that before this patch the length of the mag field reported
quite different from the expected. After this patch, the same experiments
showed reasonable values.
This is part of the transition to make all mag field values be used in
milligauss. Additionally the value of _gain_multiple is adapted to the new way
we're using it and corrected accordingly to the datasheets.
The use of _gain_multiple is not necessary because the values of
expected_{x,yz} and _mag_{x,y,z} are both in sensor raw unit (i.e., lsbs).
That wasn't fixed before in order not to make APM users to recalibrate their
compasses.
The failure to initialise the magnetometer bias states to zero can result in a large jump in yaw gyro bias and heading when a heading reset is performed.
Fixes a potential error where changes to timing and arrival rate of magnetometer and baro data could block the fusion of synthetic position and velocity measurements, allowing unrestrained tilt errors during operation without GPS or optical flow.
Fusion of synthetic position or velocity measurements is now timed to coincide with fusion of barometer observations.
If a new barometer observation has not arrived after 200 msec then the synthetic position or velocity is fused anyway so that fusion of synthetic position or velocity observations cannot occur any slower than 5 Hz
Previous check default only checked the number of satellites and horizontal position accuracy.
Updated default value also checks HDoP and speed accuracy.
Fixes the issue of three unused variables, two of which were used in a
commented Debug() call.
To keep the convenient debug message (and the variable names for the
data bytes), this patch uncomment the debug call but wrap the variables
and the debug call around an ifdef for the local symbol
gsof_DEBUGGING. So by turning it on, the debug will already be in place.
The Debug() call was modified to actually compile and include the third
variable in the output.
It uses a heating resistor controlled by a pwm.
By changing the duty cycle of the pwm, we can control the temperature.
A simple PI algorithm is used in order to get to the correct temperature
fast enough and without too much overshoot
It is implemented as a member of the Util class in order not to make to much
modification to the current codebase
Read temperature as part of the normal burst. This is not very costly since it
is part of the burst read in i2c and already read in spi.
It is meant to be used for imu heating.
The filter is set to 1Hz on temperature because of the inherent inertia of
heating systems.
Surround calls to rcout->write() with rcout->cork() and rcout->push().
If the RCOutput implementation allows the writes are grouped and only
sent together to the underlying hardware.
Fix warning and use htole16 instead of trying to implement it.
The current code does nothing on little endian platforms.
Moreover, the status variable was unused.
MPU6000 data sheet indicates that variation on gyro ZRO across temperature range from -40 to +85 is +-20 deg/sec.
The limits on the gyro bias states have been increased to allow for this.
To enable the EKF to accommodate such large gyro bias values in yaw without the yaw error wrapping, leading to continual heading drift, an unwrap function has been applied to the compass heading error.
In 294298e ("AP_InertialSensor: use method for downcast") I was too eager
to use "auto" and ended up using the implicit copy constructor instead
of actually getting a reference to the object.
This was only used for supporting APM1. The removal was mostly automatic
with:
sed -i 's/pgm_read_byte(&_motor_to_channel_map\[\([^]]*\)\])/\1/g' libraries/AP_Motors/*.cpp
sed -i 's/_motor_to_channel_map\[\([^]]*\)\]/\1/g' libraries/AP_Motors/*.cpp
And then remove references to MOTOR_TO_CHANNEL_MAP and
_motor_to_channel_map and make sure the variable used in shifts is
unsigned
This method is not used anymore since the introduction of channel map and
allowing motors to be enabled/disabled in AP_Motors.
Later we may introduce a method to write multiple values with a default
implementation that supports the channel and enable maps rather than
requiring all subclasses to implement this method.
This is the only place where this variant of RCOutput::write() is
called. Remove it so to use the common interface. It can be added back
later when there's support for asynchronous write.
Now that most places in the code use the ARRAY_SIZE macro instead of
coding it by hand, let's use some type safety in its definition. This is
a C++ version of similar macros used in kmod, Linux kernel and the
source of them, ccan.
A C++ version like this is used in V8 (the JS engine) and other open
source projects.
The main benefit of this version is that you get a compile error if you
pass in a variable that's not an array. For example,
Bla y[10];
Bla *y_ptr = y;
void foo(Bla x[])
{
// build error since x[] decay to a pointer in function
// parameter
for (int i = 0; i < ARRAY_SIZE(x); i++) {
...
}
// build error since y_ptr is not an array
for (int i = 0; i < ARRAY_SIZE(y_ptr); i++) {
...
}
}
I added the additional specialization to allow arrays of size 0.
If there is a read error, reading from the adc will return 0 but moreover,
we need to re-initiate a read or else we are stuck forever.
From MS5611-01BA03 datasheet, p. 10, CONVERSION SEQUENCE:
"After the conversion, using ADC read command the result is clocked out with the MSB first.
If the conversion is not executed before the ADC read command, or the ADC read command is
repeated, it will give 0 as the output result."
Instead of just doing a static cast to the desired class, use a method
named "from". Pros:
- When we have data shared on the parent class, the code is cleaner in
child class when it needs to access this data. Almost all the data
we use in AP_HAL benefits from this
- There's a minimal type checking because now we are using a method
that can only receive the type of the parent class
Instead of just doing a static cast to the desired class, use a method
named "from". Pros:
- When we have data shared on the parent class, the code is cleaner in
child class when it needs to access this data. Almost all the data
we use in AP_HAL benefits from this
- There's a minimal type checking because now we are using a method
that can only receive the type of the parent class
Instead of just doing a static cast to the desired class, use a method
named "from". Pros:
- When we have data shared on the parent class, the code is cleaner in
child class when it needs to access this data. Almost all the data
we use in AP_HAL benefits from this
- There's a minimal type checking because now we are using a method
that can only receive the type of the parent class
Instead of just doing a static cast to the desired class, use a method
named "from". Pros:
- When we have data shared on the parent class, the code is cleaner in
child class when it needs to access this data. Almost all the data
we use in AP_HAL benefits from this
- There's a minimal type checking because now we are using a method
that can only receive the type of the parent class
we should use baro height not hgt_afe for the climb rate filter. This
makes the climb rate consistent with the one from the EKF. The lidar
correction comes in with the demanded height, not the observed height
the previous approach assumed a 1:1 mapping between compass backends
and compass instances, which isn't true on PX4.
It also only setup milligauss offsets on a set_and_save call, which is
not the only way offsets change
this adds a milligauss_ratio per instance, which is considerably
simpler
Due to the description string getting to long HDop was renamed as EPH with VDop as EPV (Which is the same terimnology used to describe the MAVLink side). Status was shortened to stat as well.
AK8963 is configured in 16-bit ADC mode which implies sensitivity of 0.15 uT/LSb. Knowing this fact we can convert the measurements to the proper units. The change will make users recalibrate their compasses.
From now on there's a pair get_field_milligauss() and
get_offsets_milligauss() that can make the transition to the common
units across all compasses easier.
compile time optimization
Functions like sq() are better moved to the header file as inline.
Compiler can then optimize these out when used in code, this saves cpu
cycles with stack push, pop during function calls.
- add get_prev_nav_cmd_with_wp_index(). This is different than get_prev_nav_cmd_index() in that it only stores the index if there is a valid lat/lng (+1 squashed commits)
- added mission item command to NAV_LAND which is the abort takeoff altitude. If 0 then use last takeoff if available, else use 50m
This is a good way of letting each implementation easily calculate vibration
and clipping: all they need to do is publish their sample rate and they don't
need to worry about the call for calculation.
These changes are for enabling unified accelerometer vibration and clipping
calculation. For that, we need the values "rotated and corrected" before they
are filtered and the calculation must be called as soon as a new sample arrives
as it takes the sample rate into account.
Thus, move code that applies "corrections" to be executed as soon as accel data
arrive and call _publish_accel() passing rotate_and_correct parameter as false.
Also, do the same for gyro so we can keep it consistent.
These changes are for enabling unified accelerometer vibration and clipping
calculation. For that, we need the values "rotated and corrected" before they
are filtered and the calculation must be called as soon as a new sample arrives
as it takes the sample rate into account.
Thus, move code that applies "corrections" to be executed as soon as accel data
arrive and call _publish_accel() passing rotate_and_correct parameter as false.
Also, do the same for gyro so we can keep it consistent.
These changes are for enabling unified accelerometer vibration and clipping
calculation. For that, we need the values "rotated and corrected" before they
are filtered and the calculation must be called as soon as a new sample arrives
as it takes the sample rate into account.
Thus, move code that applies "corrections" to be executed as soon as accel data
arrive and call _publish_accel() passing rotate_and_correct parameter as false.
Also, do the same for gyro so we can keep it consistent.
These changes are for enabling unified accelerometer vibration and clipping
calculation. For that, we need the values "rotated and corrected" before they
are filtered and the calculation must be called as soon as a new sample arrives
as it takes the sample rate into account.
Thus, move code that applies "corrections" to be executed as soon as accel data
arrive and call _publish_accel() passing rotate_and_correct parameter as false.
Also, do the same for gyro so we can keep it consistent.
These changes are for enabling unified accelerometer vibration and clipping
calculation. For that, we need the values "rotated and corrected" before they
are filtered and the calculation must be called as soon as a new sample arrives
as it takes the sample rate into account.
Thus, move code that applies "corrections" to be executed as soon as accel data
arrive and call _publish_accel() passing rotate_and_correct parameter as false.
Also, do the same for gyro so we can keep it consistent.
These changes are for enabling unified accelerometer vibration and clipping
calculation. For that, we need the values "rotated and corrected" before they
are filtered and the calculation must be called as soon as a new sample arrives
as it takes the sample rate into account.
Thus, move code that applies "corrections" to be executed as soon as accel data
arrive and call _publish_accel() passing rotate_and_correct parameter as false.
Also, do the same for gyro so we can keep it consistent.
These changes are for enabling unified accelerometer vibration and clipping
calculation. For that, we need the values "rotated and corrected" before they
are filtered and the calculation must be called as soon as a new sample arrives
as it takes the sample rate into account.
Thus, move code that applies "corrections" to be executed as soon as accel data
arrive and call _publish_accel() passing rotate_and_correct parameter as false.
Also, do the same for gyro so we can keep it consistent.
Also fix bug in do-mount-control so that do-mount-control can switch mount into retract mode
Also removes ability to set which axis are stabilized through
ardupilotmega mount_configure message
It's possible to use the internal clock in PCA96895 if we account for
the drift it contains. This is a bit different from solutions in other
projects like the Adafruit library and the PX4 firmware: instead of
applying a correction to the final frequency we apply the correction to
the clock since this is the source of the error.
With this fix we arrived to much better results across different lots of
sensors.
The Navio board continues to use the external clock and should have no
difference behavior.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
increase iterations to get good results from LM
better check for convergence, comparison with initial fitness is a better way to determine if convergence occurs, if fitness has not improved compared to initial fitness it means optimiser has failed.
If we have an error in the SPI or I2C transaction we should not change
the state. Otherwise we might read a temperature when the sensor is
reporting pressure and vice-versa.
irlock_center_x_pos calculates the lateral x position of the marker in cm. relative to the quad
irlock_x_pos_to_latlon rotates the frame based x position to latitude/longtitude based coordinates
same case for the y position
add get_angle_to_target method
get_angle_to_target replaces pixel to position calculations
Also removed ahrs reference (now in AC_PrecLand lib), unused references
to orb and commented out parameter declaration
reduce max objects to 5
remove ahrs reference
add timeout
return true if new sample found
bug fix get_angle_to_target
remove unused get_frame
* Retains ability to read from Analog Pin
* Adds ability to read RSSI from PWM channel value as is done in OpenLRSng, EazyUHF, and various other LRS.
* Handles any type of RSSI that provides RSSI values inverted - i.e. when the low value is the best signal and the high value is the worst signal.
* Has different key names from all existing RSSI parameters to provide for a clean break and easier distinguishing.
Like was done to inertial AK8963 and inertial sensor move the decision
regarding the I2C bus to the caller. We don't allow changing the address
because apparently HMC5843 doesn't support different addresses.
Changing only the bus could be more easily done but this prepares the
ground for using HMC5843 on an AuxiliarBus.
The need for a more generic abstraction is evidenced by this commit: a
"SerialBus" in AP_HAL would be a nice addition rather than letting each
driver to provide its own. However the methods are a little bit
different from what we have in AK8963. It's safer to do the simple
conversion now and later on to add the abstraction changing everybody to
use it.
read() calls accumulate() which takes the lock by itself so we must
release it like we were doing before 669ae26 ("AP_Compass: encapsulated
calibration in HMC").
Just like was done for inertial sensor, different detect() functions
might need different arguments and passing a pointer to function here is
cumbersome. For example, it forces to have a method like "detect_i2c2"
rather than allowing hal.i2c2 to be passed as parameter.
In order to allow other libraries to use the InertialSensor we need a
way to let them to get the only instance of InertialSensor. The
conventional way to do a singleton would be to let the constructor
private and force it to be instantiated from the get_instance() method.
Here however we just call panic() on the constructor if there's already
an instance alive. This allows us to let the vehicles as is. Later we
can change it so they call the get_instance() method instead.
Add an AuxiliaryBus class that can be derived for specific
implementations in inertial sensor backends. It's an abstract
implementation so other libraries can use the auxiliary bus exported. In
order for this to succeed the backend implementation must split the
initialization of the sensor from the actual sample collecting, like is
done in MPU6000.
When AP_InertialSensor::get_auxiliary_bus() is called it will execute
following steps:
a) Force the backends to be detected if it's the first time it's
being called
b) Find the backend identified by the id
c) call get_auxiliary_bus() on the backend so other libraries can
that AuxiliaryBus to initialize a slave device
Slave devices can be used by calling AuxiliaryBus::request_next_slave()
and are owned by the caller until AuxiliaryBus::register_periodic_read()
is called. From that time on the AuxiliaryBus object takes its ownership.
This way it's possible to do the necessary cleanup later without
introducing refcounts, that we don't have support to.
Between these 2 functions the caller can configure the slave device by
doing its specific initializations by calling the passthrough_*
functions. After the initial configuration and register_periodic_read()
is called only read() can be called.
Identify backend with an id, allowing other libraries to connect to
them. This is different from the _product_id member because it
identifies the sensor, not the board the sensor is in, which is
meaningless for our use case.
This allows backends to have a separate detection and initialization
logic. It doesn't change any backend yet and with the current code
there's no change in behavior either. This only allows
AP_InertialSensor::_detect_backend() to be called earlier so
AP_InertialSensor object can be used by other libraries. If it's not
called, later on AP_InertialSensor::init() will detect and start all
backends.
We were able to read only the block of registers that are part of the
data output from accelerometer/gyroscope. In order to support reading
the external sensors we need support for reading a generic block of
registers.
Now that we have a pre-arm check in place to detect bad lidar, the motion check is unnecessary and can false trigger for copters with flexible undercarriages or on uneven ground.
This param seems to have been un-implemented. This is putting it back in. Adds a meter offset to the calculated altitude form the baro sensors.
Also changes it from int8 to float
There are implementations for float, Vector2f and Vector3f for the Low
Pass Filter and the *2p filter. I tried to implement these filters
with one common template implementation. This implementation saves
some lines of code and reduced the redundancy. One could save even
more code if the currently overloaded isinf/isnan functions and checks
can be removed.
Signed-off-by: Daniel Frenzel <dgdanielf@gmail.com>
very strict check that all axis are not vibrating much at all
new param: INS_STILL_THRESH used to be a vibration threshold for different platforms
// @Description: Threshold to tolerate vibration to determine if vehicle is motionless. This depends on the frame type and if there is a constant vibration due to motors before launch or after landing. Total motionless is about 0.05. Suggested values: Planes/rover use 0.1, multirotors use 1, tradHeli uses 5
Param 1 denotes which direction the user expects the plane to
travel when changing altitude:
0 = no expectation, command completes when within 5 m of altitude.
1 = climb expected, command completes at or above altitude.
2 = descent expected, command completes at or below altitude.
This method checks for consistency between accelerometer readings and switches to the unit with the lowest vibration of the difference exceeds 0.3g
The threshold of 1.7 m/s/s corresponds to a maximum tilt error of 10 deg assuming one IMU is good, one is bad and the EKF is using the bad IMU.
Now instead of requiring the buffer to fill completely before we can
detect it is not draining, we use a time based mechanism to detect
when none of the first few bytes are transmitted after sitting in our
buffer a half second or more after flow control is enabled. This
huristic is reliable only for the first several chracters because we
believe that the radio must still have plenty of room in it's own
buffers at that time even if it is not able to transmit them to the
other radio yet. Note that the original algorithm made the same
assumption.
The new algorithm is especially helpful for cases where only keepalive
messages are transmitted before other packets can be requested by the
GCS. In this situation, the original code required almost 2 minutes
to disable flow control and allow communication with the GCS.
It was not only standardized, but actually fixed since ".." would not
move to the libraries/ directory (and hence the include location was
actually wrong).
This is really just calculating the hamming weight of the GNSS_MODE bitmask, but I don't know if the APM compiler could handle the GCC intrinsic that could calculate it faster, and this is done so rarely there isn't a significant penalty to using the for loop.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
in copter if you try to set RATE_RLL_D to 0 when you haven't
prevviously changed it then it would set it, but would revert on the
next reboot. This is because of the special case handling of a set to
the "default" value. That default value is unaware of the PID
constructors
this fixes that behaviour by forcing a save if the parameter changes
value
We were previously leaking the AP_MPU6000_BusDriver if the
~AP_InertialSensor_MPU6000::detect*() failed. In order to avoid the
leak move the repeated code in a single private _detect() member that
receives everything as argument. Then this method takes ownership of the
objects.
By a adding a destructor to AP_InertialSensor_MPU6000 it becomes easier to
free the objects it takes ownership of.
Different detect() function might need different arguments and passing a
pointer to function here is cumbersome. For example, it forces to have a
method like "detect_i2c2" rather than allowing hal.i2c2 to be passed as
parameter.
The methods actually use the enum from AP_HAL::SPIDeviceDriver, so don't
declare a new one. The I2C implementation is empty; if we actually start
to use it we'd better move the bus abstraction to HAL.
Provides a stable fallback, and can be considered fairly safe from the perspective that it provides a worse value then the hDOP under almost all scenarios.
When writting or reading a block, if the block doesn't fit the area where it begins, the next base address is always zero. Thus the calculations to define the next value of addr are unnecessary.
Here's a quick validity proof using the previous calculations:
First: Considering the case where the block doesn't fit it's first area:
That means that (count + addr > length), what makes:
count = length - addr; (1)
So the following operations:
addr += count;
addr -= length;
Are the same as doing:
addr = addr + count - length; (2)
Using (1) and (2) we have:
addr = addr + length - addr - length = 0
Second: When the block fits the area where it's at:
That means that variable count is not changed,
thus (n -= count) evaluates to 0, which makes the loop exit.
Another change was (b += count;) being moved after the condition to break the loop, since we just need to move the block pointer when it doesn't fit the first area.
remove PANICs from init
return semaphore if init fails
add successful initialisation check before attempting to read from sensor
structure made private where possible
formatting fixes
check I2C reads succeed
add request_measurement to request sensor to produce measurement
quit after 20 of previous 40 reads fail
throttle reads to 10hz max
In case of error or zeroed data, the i2c semaphore wasn't given.
It happened at first startup on Bebop and caused a failure:
"PANIC: failed to take _bus->sem 100 times in a row..."
this makes it possible to bootup ardupilot before the desired network
interface is available. This is very useful for when using 3G dongles
in aircraft
The current implementation doesn't throw an error on a malformed path string.
i.e. udp:192.168.1.1.14550 instead of udp:192.168.1.1:14550 may result in a memory leak or whatsoever.
The commit fixes the issue and outputs a nice error message if anything's wrong.
No need to repeat the same comments on 3 different places. Instead add a
single comment to explain how start_measurements() and read_raw() are
related.
Don't use a state machine in AK8963: the start_measurements() method
should be called only once. Even if there's a magnetic sensor overflow
the only thing we should do is to discard the new data.
This also moves the _collect_samples() method to be inside _update()
since it's the only place it should be called from, the one running on
the timer thread.
We need to check the AK8963's id before anything else Here we are
reordering the calls to _calibrate() and _check_id(). After that we
don't need to read and write again the AK8963_CNTL1 register.
While at it do some renames as well:
- _configure() -> _setup_mode(): since now there's a
_bus->configure() it became confusing what actually it's
doing.
- make error messages say what we were actually trying to do but
couldn't. Also remove PSTR since this is linux-only.
- start_conversion() -> start_measurements(): We are instructing the
bus to start to get the samples, not to tell the chip to start an
analog->digital conversion like in other sensors.
The MPUREG_PWR_MGMT_1 defines were used when we cared about the MPU9250
initialization code. Now all initialization is done by the MPU9250 class
itself, so remove these defines.
Also remove AK8983_SELFTEST_MAGNETIC_FIELD_ON that is never used and let
the defines always with 2 bytes to improve readability.
Similar code was added in the read_raw() implementation for each bus.
Add a new POD struct read_raw to contain the registers from the AK8963
and use it instead as argument.
DMA is getting stopped in the separate method now. This is the best we
can get at the current time. It does yield slightly better experience
and works in the majority of cases.
The patch is a no bulletproof solution, though.
There's a possibility of corruption in case of e.g. a SIGKILL. There's
no signal framework at the time and the commit doesn't add one. That's
why all signals are handled in the same erroneous way. This is not a
good nor a final solution to the issue.
For the issue at hand a better fix might be porting the code to kernel
space but it's a rather tediuos task that we cannot undertake in the
couple of weeks.
The issue has already come up. There's no deinitialization mechanisms at the moment. As APM is rather software than firmware on Linux, there're some clean-up work that needs to be done. This commit triggers deinitialization of RCInput on a panic.
Add a deinit() counterpart. This is needed for some ports that require some deinitializtion logic. The default implementation is empty. I'm not sure whether we need to inforce it for all.
Ublox 7 and 8 seires use a UBX-CFG-GNSS message to enable satellite constellations. The default value does not enable any additional ones, and any constellations the reciever doesn't report knowing about are not configured.
Remove race condition on sending intial blob to the GPS, it was possible to send a blob that got the GPS configured enough to allow the autodetect to take over (and then some drivers like ublox would not finish sending the blob, which has potential details that the driver might have needed to send)
Limit the delay to checking for NMEA gps to only checking after all the available baud rates have been checked
Since a UBlox will actually report having DGPS (due to SBAS or RTCM data) actually report this as the highest supported mode
The symptom was that if the very first command in the mission was a
do-command, it would be run after every nav-command that didn't have
another do-command before it.
Now that the initialization of MPU9250 is shared between the
AP_InertialSensor and other drivers using it as a backend, we can reset
the MPU9250 in order to put it in a known state.
Now we have the initialization code split in 2 parts:
1) Making sure the MPU9250 chip is alive and working: this is now in a
static function that may be called by other drivers that use MPU9250 as
backend.
2) The configuration of gyro and accel. Once the first part is completed
successfully the AP_InertialSensor_MPU9250 finishes the configuration of
the sensors it uses.
The only change in behavior here is that before we would try 25 time (5x
inside _hardware_init time 5x inside _init_sensor() that calls the first
function) to "boot the chip" and now we are doing "only" 5.
Add static methods to do the SPI transactions and provide the wrapper
methods when we have an instance of the object. This is useful so these
methods can be called from other contexts when the AP_InertialSensor
hasn't been initialized yet.
Allowing to change the SPI device state allows us to save the
information whether the device was already initialized and avoid 2
separate drivers to initialize it.
Uses reimplemented AK8963 driver. There's also no need trying to detect this
compass twice. Actually, it might even be bad, because the current code can
allocate an AK8963 object twice.
If a badly conditioned covariance matrix causes negative innovation variances, then the filter will diverge. The previous approach of increasing process noise was not effective in some cases, so a hard reset of the covariance matrix has been adopted to guarantee recovery.
This fixes a numerical error observed using the replay on flight log which had significant periods of compass rejection.
The Compass library is initialized before the InertialSensor. AK8963 with
MPU9250 as backend already takes care of resetting MPU9250. The problem with
also resetting it in the MPU9250 initialization code is that if the reset
happens during an internal I2C transaction, the AK8963 may hang. So here we
remove the reset inside MPU9250. There still a possibility that the first
MPU9250 initialization is not successful and it resets the chip, but it's not
happening in tests.
new param: BRD_SERIAL_NUM
// @Description: User-defined serial number of this vehicle, it can be any arbitrary number you want and has no effect on the autopilot
// @Range: -32767 to 32768 (any 16bit signed number)
The value for LINUX_STORAGE_SIZE was defined inconsistently against the one
defined for Linux boards in HAL_STORAGE_SIZE. That led to some values not
being written to the storage when running the test binary built at
libraries/StorageManager/examples/StorageTest.
As we intend to eventually get board related parameters from a configuration
file, this commit makes the GPIO numbers for data-ready pins be instance
variables instead of from C constant macros.
Another advantage of using instance variables in this context is the
possibility of using more than one LSM9DS0.
If the data-ready polling is done entirely on GPIO pins, it isn't necessary to
hold the semaphore before we now we have data to consume. In that case, only
take the SPI semaphore if there's new data available.
On the other hand, if at least one SPI transaction is done in order to check
for new data, then it makes sense to take the semaphore beforehand.
This commit makes accel and gyro initialization routines use bitfield macros
instead of hardcoding the literal value when wrinting on registers. That is
less prone to typos and a lot of times self-explanatory. Also, due to the
latter, the long comments explaining each register field were removed (any
detail can be checked on the datasheet).
This adds the backend driver for LSM9DS0. This implementation is based on the
legacy driver coded by Víctor Mayoral Vilches (under folder LSM9DS0) and makes
some necessary adaptations and fixes in order to work properly. The legacy
driver folder was removed.
The calibration on LSM9DS0 was giving offsets between 4.0 and 4.2 on x-axis and
around 3.6 on y-axis. It turned out that those offsets were actually right.
The maximum absolute values of calibration offset should be a sensor
characteristic rather than a constant value for all sensors.
The constant value previously used (3.5 m/s/s for all axes) is set here as a
default maximum absolute calibration offset for every instance to keep it
working.
The device number in /dev may not be reliable from one boot to another
due to the initialization order of each bus.
For example, in Minnow Board Max, the exposed I2C buses may be i2c-7 and
i2c-8 or i2c-8 and i2c-9 depending if the platform driver in the kernel
is initialized before or after the PCI.
It also may change with different version and configuration of the DT or
UEFI used making another kernel driver to bind to the device. This means that
for Minnow Board Max we need to use something like below to pass to the
constructor:
static const char * const i2c_devpaths[] = {
/* UEFI with lpss set to ACPI */
"/devices/platform/80860F41:05",
/* UEFI with lpss set to PCI */
"/devices/pci0000:00/0000:00:18.6",
NULL
};
The devpath here is the one returned by udev with the following command:
udevadm info -q path /dev/<i2c-device>
In contrary to the device number in /dev/i2c-N, this path in sysfs is
stable across reboots and can only change if there's a change in the
UEFI firmware or the board's device tree.
This patch assumes the currently supported boards don't have this
problem so it's not touching them.
- when resuming a mission we should read the value from storage of the same index to ensure we're not continuing an old cached version of the mission item.
- inherent problem: DO commands will continue and will be unaffected unless the new mission has a different DO_ command structure. If so, a set_current_cmd() or reset() should be issued by the GCS.
The previous implementation made some boards apply two rotations to suit
their default orientation. That was happening because there was an
unconditional rotation being done (commented as "rotate for bbone
default").
This commit makes that unconditional rotation as a default rotation
instead and adjusts the former additional rotations to be single
rotations.
As the datasheet says: "To prevent switching into I2C mode when using
SPI, the I2C interface should be disabled by setting the I2C_IF_DIS
configuration bit."
We also reset the sensor like PX4Firmware does for initializing the
MPU6000. See: ee1d8cd770/src/drivers/mpu6000/mpu6000.cpp (L695)
Rapid switching between GPS receivers can cause real problems.
Switch if:
1) secondary GPS has 1 more satellite for at least 20 seconds
OR
2) secondary GPS has 2 more satellites for at least 5 seconds
Fixes https://github.com/diydrones/ardupilot/pull/2320
Check by false instead of checking by -1. Fix the following compiler warning
with gcc 5.1.0:
ardupilot/libraries/AP_Notify/ToneAlarm_Linux.cpp:64:13: warning: comparison of constant '-1' with boolean expression is always false [-Wbool-compare]
if (err == -1) {
^
Also change the initialization code not to use -1.
This patch increases initial gyro bias uncertainty and plane and rover specific process noise to improve the rate of gyro bias learning.
This reduces the likelihood of a navigation failure due to rapid temperature changes in the inertial sensors causing rapid changes in zero rate offset.
The increase in process noise cannot be applied to Copter due to different numerical stability limits arising from the faster update rate.
