add bi-directional dshot
add back in features.
juggle DMA allocations to allow CRSF to work correctly
disable dshot on PWM 10 as it is not used
do not enable quadplane by default
do not disable arming checks
run ICM42688 at 1Mhz for low speed to avoid gyro noise
add HEEWING README and picture
this was already done on many (most?) boards, and greatly reduces DMA
sharing which improves performance of UARTs. This changes the default
to no DMA on I2C
this fixes an issue where a lua library function triggers an exception
after it does a math operation which changes the floating point
registers on M7 MCUs (such as STM32H7). An example is math.random()
which calls math_random(), which pre-calculates a double value before
checking if the arguments to the call are valid. When it then checks
and finds invalid values the exception longjmp does not restore the
floating point registers.
this limits the amount that rate gains can reduce from the original
values in a quicktune. Large reductions in rate gains can be
incorrectly triggered by a frame resonance or gust of wind which can
result in gains that are dangerously low, which can trigger an angle P
oscillation
The check for the aircraft being lined up for a tangent exit has an early breakout condition if the next waypoint is too close to the loiter circle which can prevent the required ground course to waypoint ever being achieved. This check was using the WP_LOITER_RAD parameter value, not the actual radius being used which can be set differently by the mission plan. If a large value for WP_LOITER_RAD was set and being over-written by the mission plan with a smaller value compatible with the distance to the next waypoint, the aircraft would still exit early.
this fixes a bug where TECS maintains its slow integrator while in a
VTOL hover mode in AUTO or GUIDED.
Among other things this affects PAYLOAD_PLACE and
DO_VTOL_TRANSITION. In those states the height can change while
hovering outside the control of TECS. When TECS regains control in a
fwd transition then can lead to a very large height loss or gain until
the TECS integrator can catch up
this test was relying on the EKF bug fixed in this PR. The copter was
actually fully landing and touching the ground in the LAND phase
whereas the original intention of this test was that it not touch the
ground in LAND. See the graph in
https://github.com/ArduPilot/ardupilot/pull/17104 where the test was
added
The ResetVelocity() function is only supposed to reset XY states, not
Z state. Resetting the Z state for velocity results in a large
velocity glitch if a vehicle is descending or ascending when aiding
switches to AID_NONE
this fixes#19386
The ResetVelocity() function is only supposed to reset XY states, not
Z state. Resetting the Z state for velocity results in a large
velocity glitch if a vehicle is descending or ascending when aiding
switches to AID_NONE
this fixes#19386
this sets up the vwd integrator more reasonably when we are in
POSITION1 stage of VTOL landing. We need to have enough throttle to
cope with a headwind, but want it lower when we are at or above our
target closing speed so can minimise the amount of pitch up
This also makes the landing_desired_closing_velocity() consistent with
the landing speed used in approach, using average of airspeed min and
cruise speed if TECS_LAND_ARSPD is not set
The target airspeed for TECS during airbraking is now set to
ARSPD_FBW_MIN, on the basis we are trying to slow down to min speed,
and we have VTOL support which should prevent a stall.
To cope with a high headwind where ARSPD_FBW_MIN is below the headwind
we now check for too low achieved closing speed and switch to
POSITION1 which can use vfwd to get to the landing location
Andy Piper
HelloLeFei
Mikhail Degtiarenko
Andrew Tridgell
bugobliterator
Randy Mackay
Peter Barker
Paul Riseborough
Michael du Breuil
Stephen Dade
Tatsuya Yamaguchi
jfbblue0922
Alexander Keller
davidsastresas
Henry Wurzburg
Iampete1