Commit Graph

3255 Commits

Author SHA1 Message Date
Randy Mackay
5fe86a657e Copter: land_do_not_use_GPS has no return value 2014-04-27 15:41:41 +09:00
Randy Mackay
0665cf6b28 Copter: RTL alt should not be above fence alt
Resolves issue #435
If the altitude fence is enabled, when the vehicle RTLs it will return
at the lower of the RTL_ALT and the FENCE_ALT_MAX
2014-04-27 15:41:37 +09:00
Randy Mackay
4686eef266 Copter: GPS failsafe ensures LAND is pilot-controlled
This resolves issue #880 in which if a GPS failsafe occurred while the
vehicle was already in LAND mode, the LAND would continue to be GPS
controlled LAND instead of pilot-controlled LAND
2014-04-27 15:11:47 +09:00
Randy Mackay
dba8fac515 Copter: remove unused variables from fence.pde
saves 2 bytes
2014-04-27 11:11:12 +09:00
Randy Mackay
1aeaa5955b Copter: integrate 10sec manual recovery after fence breach 2014-04-27 11:11:09 +09:00
Randy Mackay
20de5b3006 Copter: Loiter clears out pilot acceleration when failsafe occurs
This ensures invalid pilot desired accelerations are cleared from the
loiter controller.  This is probably not strictly necessary because the
vehicle should switch out of Loiter and into RTL during failsafe.
2014-04-25 14:45:19 +09:00
Randy Mackay
05d9dc5cba Copter: RTL always land if in radio failsafe
Resolves issue in which vehicle would get stuck at RTL_ALT_FINAL if
failsafe occured.
Also clear out pilot acceleration from loiter controller if failsafe
occurs during the final descent.
2014-04-25 14:45:16 +09:00
Randy Mackay
40650aeb68 Copter: roll and pitch nudging in RTL descent 2014-04-25 14:17:03 +09:00
Michael Oborne
68f439acbe Fix auto doc group names 2014-04-25 07:53:03 +08:00
Randy Mackay
19f1e7fec4 Copter: disable Parachute by default
This saves 1k of flash and we are desperately low on the APM1/APM2.
Hopefully we can find savings somewhere and re-enable it by default.
2014-04-24 19:02:32 +09:00
Randy Mackay
ea64438ef9 Copter: RTL ensures heading is back to initial heading
This fixes the issue in which a short RTL_LOIT_TIME could cause the
vehicle's heading to be caught between it's heading when it arrived at
home and the initial armed heading.  With this fix it now waits above
home until the timer has run out AND the heading is within 2degrees of
the initial armed heading.
2014-04-24 18:54:49 +09:00
Randy Mackay
e23115516d Copter: disarm after completing RTL
Note that an RTL command executed in AUTO mode will also disarm when it
lands and pilot's throttle is put to zero and no further commands will
be executed.  This is normally not an issue because missions generally
end with an RTL (instead of having the RTL in the middle) and a work
around is available in that the LAND command could be used instead of
RTL.
2014-04-24 17:27:30 +09:00
Randy Mackay
a5602c5f14 Copter: updated contributors list
Add JulianD and SandroT and replaced tabs with spaces
2014-04-24 11:28:41 +09:00
Ju1ien
78a3e0f5a2 Copter: Hybrid removed Wind_comp_estimate filter
Removed useless call of function
hybrid_get_wind_comp_lean_angles(hybrid.wind_comp_roll,
hybrid.wind_comp_pitch);
Removed 10Hz filter for hybrid_update_wind_comp_estimate()
2014-04-24 11:28:37 +09:00
Randy Mackay
287af8f66e Copter: disable optical flow by default
We have run out of flash on the APM2, it was a choice between Hybrid
flight mode and OF_Loiter
2014-04-23 15:27:08 +09:00
Randy Mackay
55e7e1eb3e Copter: allow HYBRID to be disabled to save flash
Hybrid flight mode costs 4.5k of flash which currently puts us over the
limit for APM1 and APM2 unless optical flow or other features are
disabled
2014-04-23 15:27:05 +09:00
Randy Mackay
ba94fc9796 Copter: Hybrid move reset_I into structure
Saves 1 byte of RAM
2014-04-23 15:00:09 +09:00
Ju1ien
ff532a06ec Copter: Hybrid fixes to wind_comp, brake pitch timer, thr peaks
There was an error in the velocity axis used to update
brake_timeout_pitch (vel_right instead of vel_fw)

The wind_comp was not enough filtered for the Pixhawk (400Hz), so I
added a specific time constant (TC_WIND_COMP) to have the expected
filter with 400Hz controllers.

About throttle peaks, after some tests and from logs, they happen when
hybrid switches to loiter.
There is always a difference between Alt and DesiredAlt (DAlt), but,
when loiter engages, it initializes DAlt = Alt and the copter tries
immediatelly to reach that new setpoint. So the solution would be to
init_loiter_target() just as it was in pre-onion code : only x/y and not
z. and to be able to pass parameters like that
wp_nav.init_loiter_target(inertial_nav.get_position(), Vector3f(0,0,0));

Well, from this new code structure, it seems not possible with current
functions so I've used set_loiter_target that init position passed as
parameter and velocity to 0 (as expected).
BTW, I think there was something wrong with set_loiter_target function,
the "Vector3f& position" parameter was not used at all...
I moved the reset flag from init_loiter_target to set_loiter_target.
2014-04-23 15:00:04 +09:00
Ju1ien
14cbb09804 Copter: hybrid add Brake or Loiter to Pilot override transition
Corrected a little mistake in get_wind_comp...()
Mixed transition not only from loiter but as well from brake to manual
override
2014-04-23 15:00:01 +09:00
Ju1ien
43b1dd748b Copter: hybrid init brake roll and pitch at loiter exit 2014-04-23 14:59:59 +09:00
Ju1ien
d745060c80 Copter: fix Hybrid flight mode in Parameter description 2014-04-23 14:59:56 +09:00
Ju1ien
f8e8d4024d Copter: Hybrid's max brake angle to 30deg 2014-04-23 14:59:53 +09:00
Ju1ien
b3e8112d24 Copter: Hybrid fix wind_comp time constant
Corrected timer init values and wind_comp time constant to get the best
behaviour

Check if wider deadband required (current is 30).
We were using a comparison to a 70-100 cdeg deadband in our initial
code. The deadband was there to avoid unwanted switches in case of
inaccurate fingers/radio

Adjusted timers to 100/400Hz

I_term does not init when in hybrid loiter
2014-04-23 14:59:43 +09:00
Randy Mackay
4778c73de2 Copter: Hybrid 10hz updates to wind comp lean angles 2014-04-23 14:59:40 +09:00
Randy Mackay
f87ab21063 Copter: Hybrid estimates wind when speed under 10cm/s 2014-04-23 14:59:38 +09:00
Randy Mackay
d36f137bf8 Copter: allow arming, disarming in Hybrid mode 2014-04-23 14:59:35 +09:00
Randy Mackay
e2aaafe40b Copter: hybrid works for 100hz and 400hz 2014-04-23 14:59:33 +09:00
Randy Mackay
705ff3f44f Copter: add hybrid_mix_controls
Allow wind comp estimate to run when vehicle travelling up to 30cm/s
(was 10cm/s)
2014-04-23 14:59:30 +09:00
Randy Mackay
e48c93d93c Copter: restructure hybrid into more states 2014-04-23 14:59:28 +09:00
Randy Mackay
f467d7bc20 Copter: add Hybrid parameters 2014-04-23 14:59:25 +09:00
Randy Mackay
754bae5748 Copter: refactor and split out wind compensation 2014-04-23 14:59:23 +09:00
Randy Mackay
d9c685323a Copter: add hybrid state struct, formatting changes 2014-04-23 14:59:20 +09:00
Randy Mackay
b5ed23f592 Copter: integrate skeleton Hybrid mode 2014-04-23 14:59:17 +09:00
Ju1ien
832fc62016 Copter: control_hybrid initial version 2014-04-23 14:59:15 +09:00
Randy Mackay
5fc071f5f9 Copter: restore SITL to run at 100hz 2014-04-21 21:46:22 +09:00
Andrew Tridgell
e07b70de4e Copter: set AHRS vehicle class 2014-04-21 18:13:13 +10:00
Randy Mackay
01538c5290 Copter: remove unused lon_error, lat_error 2014-04-21 15:06:32 +09:00
Randy Mackay
8ac14023b4 Copter: set main loop rate from CPU class
Previously this was determined by the board
2014-04-21 13:32:00 +09:00
Randy Mackay
a1edf347bf Copter: STB_RLL_P and STB_PIT_P @Range 3 to 12 2014-04-21 10:41:01 +09:00
Randy Mackay
b9845047f4 Copter: bug fix AP_Rally param directory 2014-04-19 22:37:01 +09:00
Randy Mackay
7af5d4a8ce Copter: remove RALLY_WP_SIZE definition 2014-04-19 15:00:30 +09:00
Andrew Chapman
fa3732ac6d Copter: integrate AP_Rally 2014-04-19 15:00:23 +09:00
Randy Mackay
817c893f21 Copter: bug fix for conditional_distance command
Due to a race condition, the wp_distance was not being updated before
the conditional_distance
2014-04-17 22:23:28 +09:00
Randy Mackay
f29ad3a2e0 Copter: bug fix for when WP_YAW_BEHAVIOR is 0 2014-04-17 16:53:06 +09:00
Randy Mackay
c53a0fcfd9 Copter: conditional yaw fix
waypoint command was setting auto_yaw_mode when it was run after the
do-cmd
yaw_look_at_heading was being set to current heading which was
overwriting the caller's desired heading
2014-04-17 16:41:36 +09:00
Randy Mackay
7f00bd7f5d Copter: default WAYPOINT to current pos if lat, lon, alt are zero 2014-04-16 20:33:43 +09:00
Randy Mackay
d2dad1b2c1 Copter: remove unused circle_desired_rotations
desired num rotations is already held in command so we save 1byte of RAM
2014-04-16 16:28:11 +09:00
Randy Mackay
e6d2692eab Copter: Loiter_Turns moves to edge of circle if location provided 2014-04-16 16:28:08 +09:00
Randy Mackay
f6676be400 Copter: integrate change in AC_Circle init
Removed init_loiter_target when vehicle landed.  We should add some
initialisation of the circle controller when landed.
2014-04-16 16:28:06 +09:00
jschall
ff9838ea27 Copter: Document stream rate parameter functionality 2014-04-15 16:05:45 +09:00
Kevin Hester
4bfd6b8ddd Copter: fixup line endings to be newline 2014-04-15 15:54:13 +09:00
Randy Mackay
cf86e304f0 Copter: add V-Tail to FRAME param's @Value 2014-04-15 12:18:31 +09:00
Randy Mackay
729026d80c Drift: get velocity using const reference 2014-04-14 11:34:17 +09:00
Emile Castelnuovo
f5a68fdba1 Copter: clear RC in overrides on GCS failsafe. 2014-04-13 22:59:51 +09:00
TeamOSEOLA
7dda8afd60 Copter: Fixed GPS_ok() status checking
Fixed the GPS_ok() so that TRUE is returned in the cases of DGPS and Assisted GPS fixes, not just 3D fix.
2014-04-11 09:01:35 +10:00
Andrew Tridgell
1189978334 Copter: ensure we log both GPS at the time we receive a message 2014-04-10 10:30:10 +10:00
Randy Mackay
e7d73aa856 Copter: enable GCS failsafe to RTL by default
This only triggers if the user has been using the GCS's RC override
2014-04-09 10:50:35 +09:00
Randy Mackay
037a0b4e5a Copter: dos2unix Parameters.h 2014-04-08 23:30:15 +09:00
Emile Castelnuovo
a9bd4e9da1 VRBRAIN: added ignore board voltage check for VRBRAIN boards. 2014-04-08 16:19:20 +10:00
Emile Castelnuovo
9e31f032c2 Copter: added VRBRAIN board #includes and #defines 2014-04-08 16:19:20 +10:00
Randy Mackay
8a4d82f43a Copter: AC3.1.3 release notes 2014-04-07 14:28:12 +09:00
Randy Mackay
9bf9e0ede9 Copter: check parachute is enabled before manual_release 2014-04-07 13:37:15 +09:00
Randy Mackay
01e5ae6e5c Copter: integrate parachute alt_min units change 2014-04-07 13:37:12 +09:00
Randy Mackay
47c1cb8b99 Copter: log parachute events 2014-04-07 13:36:59 +09:00
Randy Mackay
2b4d2697b2 Copter: process MAV_CMD_DO_PARACHUTE commands 2014-04-07 13:36:56 +09:00
Randy Mackay
56768a8d61 Copter: add min alt check to parachute release 2014-04-07 13:36:50 +09:00
Randy Mackay
340f3a7f9d Copter: ch7/ch8 parachute release 2014-04-07 13:36:47 +09:00
Randy Mackay
ac982656fd Copter: extend crash check to trigger parachute 2014-04-07 13:36:46 +09:00
Randy Mackay
ff32b27272 Copter: integrate parachute lib 2014-04-07 13:36:44 +09:00
Andrew Tridgell
ae350e42aa Copter: show next wp when not running a mission
this lets the GCS know what wp would be run if auto mode is selected
2014-04-07 11:41:05 +10:00
Andrew Tridgell
454d1f26c3 Copter: added support for SERIAL_CONTROL message 2014-04-05 07:34:34 +11:00
Andrew Tridgell
339689b578 Copter: fixed load average for different loop rates
Pair-Programmed-With: Paul Riseborough <p_riseborough@live.com.au>
2014-04-04 21:37:56 +11:00
Andrew Tridgell
27ad8c39d6 Copter: enable passthrough auxillary channels 2014-04-03 12:19:44 +11:00
Andrew Tridgell
7bf12cfd8a Copter: update for gps.setHIL() API 2014-04-02 07:55:28 +11:00
Andrew Tridgell
852cdbaa7c Copter: added GPS parameters 2014-04-01 06:38:25 +11:00
Andrew Tridgell
640b64f5e4 Copter: convert to new GPS API 2014-04-01 06:38:24 +11:00
Andrew Tridgell
198388b5e0 Copter: use AP_GPS_Auto for 2nd GPS 2014-04-01 06:38:23 +11:00
Kevin Hester
5fb3b031f1 Copter: disambiguate the various causes of "Bad GPS Pos"
I've seen a fair number of user questions where they are confused by
"Bad GPS Pos" on their GCS/not being allowed to arm.  This change splits
the remaining causes of this fault into separate messages.

Hopefully this increases the odds of the user self diagnosing...
2014-03-31 21:59:12 +09:00
Randy Mackay
9e7021cc20 Copter: Notify arming failure when using MAVLink 2014-03-31 20:34:31 +09:00
Jonathan Challinger
608b8b0a2c Copter: integrate Notify arming failure when using yaw sticks 2014-03-31 20:34:29 +09:00
Randy Mackay
4b6f03cc11 Copter: remove do_land's use of RTL_ALT_MAX 2014-03-31 20:34:21 +09:00
Jonathan Challinger
2601ac9959 Copter: Remove 80m altitude limit on RTL 2014-03-31 20:34:19 +09:00
Jonathan Challinger
045c6d8c3f Copter: Only play GPS tone when armed 2014-03-31 20:34:16 +09:00
Randy Mackay
d9fd577fb0 Copter: add Drift throttle assist constraints 2014-03-31 15:40:00 +09:00
Jason Short
50dcbe6549 Copter: Drift throttle assist range increased
Throttle assist is applied from 213 ~ 787
Deadband and constraint added
2014-03-31 13:09:57 +09:00
Jason Short
bccf1de563 Copter: add drift throttle assist 2014-03-31 13:09:54 +09:00
Randy Mackay
7d5d0d12a2 Copter: spline bug fixes
Next waypoint's location must be passed in even if it's a straight
segment.
mission.get_next_nav_cmd's start_index should be the current command +1
2014-03-29 17:57:45 +09:00
Randy Mackay
ac364c93dd Copter: bug fix for simple_mode when run at 400hz
Mark radio frame as consumed so that simple mode does not apply the yaw
correction more than once when run at very high rates (like 400hz on
Pixhawk)
2014-03-28 17:03:31 +09:00
Randy Mackay
176a450ad2 Copter: remove spline handling from regular wp_nav 2014-03-28 09:23:41 +09:00
Randy Mackay
d541fefab4 Copter: add do_spline_wp and verify_spline_wp functions 2014-03-28 09:23:33 +09:00
Randy Mackay
8f946a3a8c Copter: remove original_wp_bearing
To-Do: extend wpnav yaw control to only repoint nose towards waypoint if
it is more than 5m or 10m away
2014-03-28 09:23:21 +09:00
Randy Mackay
392162747a Copter; integrate WPNAV's get_yaw 2014-03-28 09:23:17 +09:00
Randy Mackay
3753550a72 Copter: integrate get_spline_yaw 2014-03-28 09:23:11 +09:00
Randy Mackay
c0f12911ec Copter: minor format change 2014-03-28 09:23:02 +09:00
Randy Mackay
0822adfb34 Copter: integrate spline navigation 2014-03-28 09:22:59 +09:00
Andrew Tridgell
78ba1a33aa Copter: support 18 input channels in MAVLink 2014-03-25 14:47:43 +11:00
Andrew Tridgell
c0767eebff Copter: support 14 RC channels on PX4 2014-03-25 14:47:05 +11:00
Andrew Tridgell
e1b9135946 Copter: updates for new RCInput API 2014-03-25 14:47:04 +11:00
Andrew Tridgell
3362e42478 Copter: consider health of primary compass in SYS_STATUS, pre-arm and compassmot
this should prevent users from taking off with only secondary compass
2014-03-24 19:52:08 +11:00
Andrew Tridgell
11e5b95878 Copter: updates for GPS changes 2014-03-24 12:04:46 +11:00
Randy Mackay
71f61c9bef Copter: fix typo to show ATUN FMT in dataflash logs 2014-03-21 15:44:06 +09:00
Andrew Tridgell
4a01315fc5 Copter: enable logging of RADIO_STATUS 2014-03-20 09:56:37 +11:00
Andrew Tridgell
a345a9d993 Copter: removed check on target component in arm
Thanks to DonLakeFlyer for finding this, see
https://github.com/diydrones/ardupilot/pull/909
2014-03-20 09:06:28 +11:00
Randy Mackay
88527cd01c Copter: integrate Mission cmd field changes 2014-03-19 12:14:25 +09:00
Andrew Tridgell
e4b3323455 Copter: use common deferred message handling 2014-03-19 12:14:20 +09:00
Andrew Tridgell
69252868a8 Copter: use common MISSION_ITEM handling 2014-03-19 12:14:12 +09:00
Andrew Tridgell
f4ed2beacd Copter: use new common MAVLink message handlers 2014-03-19 12:13:40 +09:00
Randy Mackay
6ef2b55602 Copter: use common GCS_MAVLink handle_mission methods 2014-03-19 12:13:22 +09:00
Andrew Tridgell
85725de9cb Copter: use new handle_mission_request()
Pair-Programmed-With: Randy Mackay <rmackay9@yahoo.com>
2014-03-19 12:13:15 +09:00
Randy Mackay
a3573f9ebd Copter: minor typo in do_change_speed processing
It is unlikely that the "f" at the end of the 100 is required to
maintain the full precision of the target speed but added just in case
2014-03-19 12:12:55 +09:00
Randy Mackay
08b78db43c Copter: use mission command specific structures 2014-03-19 12:12:54 +09:00
Randy Mackay
2f8daf2fa9 Copter: integrate dataflash Log_Write_MavCmd 2014-03-19 12:12:46 +09:00
Randy Mackay
edab06a3ff Copter: truncate mission before uploading new mission
replacing clear with truncate allows new missions to be uploaded while
the current mission is running
2014-03-19 12:12:36 +09:00
Randy Mackay
f3813593b7 Copter: use Dataflash lib's Log_Write_Cmd 2014-03-19 12:12:11 +09:00
Randy Mackay
7b6906ae3f Copter: integrate variable max num commands 2014-03-19 12:12:01 +09:00
Randy Mackay
b587d0d597 Copter: pass eeprom start to Mission constructor 2014-03-19 12:11:56 +09:00
Randy Mackay
b718b9070a Copter: call mission.init during startup 2014-03-19 12:11:47 +09:00
Randy Mackay
cc7b1c4e9c Copter: init_home checks cmd read success before logging 2014-03-19 12:11:39 +09:00
Randy Mackay
fa96e9355b Copter: init cmd before saving with Ch7/Ch8 2014-03-19 12:11:21 +09:00
Randy Mackay
0fc36fd244 Copter: CMD dataflash logs use uint16 for total and num 2014-03-19 12:11:15 +09:00
Randy Mackay
6bb05750e7 Copter: remove alt_in_cm from mavlink to cmd conversion 2014-03-19 12:11:04 +09:00
Randy Mackay
04166c1686 Copter: replace memset in GCS_Mavlink 2014-03-19 12:10:52 +09:00
Randy Mackay
c3162f67e8 Copter: integrate move of p1 from Location to mission cmd 2014-03-19 12:10:48 +09:00
Randy Mackay
aade894014 Copter: integrate replace_cmd 2014-03-19 12:10:43 +09:00
Randy Mackay
54c99d84ea Copter: integrate AP_Mission set_current_cmd 2014-03-19 12:10:39 +09:00
Randy Mackay
36af34bf8b Copter: send current wp as 65535 to GCS when mission complete 2014-03-19 12:10:34 +09:00
Randy Mackay
92738533fe Copter: auto starts only when num cmds > 1
num_commands will be 1 when there is no mission because home counts as
the first command
2014-03-19 12:10:30 +09:00
Randy Mackay
f77b2af661 Copter: use common location options masks 2014-03-19 12:10:26 +09:00
Randy Mackay
070cbc9250 Copter: use Mission mav to cmd conversion methods 2014-03-19 12:10:24 +09:00
Randy Mackay
67a4b47f6b Copter: pass ahrs into mission constructor 2014-03-19 12:10:15 +09:00
Randy Mackay
37fe229ded Copter: remove unused definitions 2014-03-19 12:10:12 +09:00
Randy Mackay
359f1a27ec Copter: process cmds from mission lib 2014-03-19 12:10:11 +09:00
Randy Mackay
6e0e672fb2 Copter: log using mission commands 2014-03-19 12:10:09 +09:00
Randy Mackay
43c7310540 Copter: ch7 save wp feature to use ap_mission 2014-03-19 12:10:08 +09:00
Randy Mackay
ffc418dfe3 Copter: add mavlink packet to cmd conversion to GCS_Mavlink.pde 2014-03-19 12:10:06 +09:00
Randy Mackay
9f03e21f81 Copter: remove low-level handling of mission cmds
Now handled by AP_Mission
2014-03-19 12:10:04 +09:00
Randy Mackay
5d568502a0 Copter: instantiate AP_Mission object 2014-03-19 12:10:03 +09:00
Randy Mackay
1bad6a4b15 Copter: add AP_Mission object parameter
Remove global command_total and command_index parameters
2014-03-19 12:10:01 +09:00
Randy Mackay
0d23c3b910 Copter: initialise vertical speed for Loiter mode 2014-03-17 10:17:57 +09:00
Holger Steinhaus
39df609235 Copter: fixed vertical speed init for ALT_HOLD mode 2014-03-17 10:12:35 +09:00
Andrew Tridgell
43d009e3a5 Copter: set 2nd GPS as secondary 2014-03-08 21:48:18 +11:00
Randy Mackay
9287e28307 Copter: bug fix display of PerfMon log's num long loops 2014-03-08 15:17:03 +09:00
Randy Mackay
54e131cf1f Copter: re-enable CLI for Pixhawk 2014-03-08 15:17:02 +09:00
Randy Mackay
6efc26d3a6 Copter: restore mount's mode to default after ROI completes 2014-03-05 16:02:14 +09:00
Randy Mackay
7992a1a7d3 Copter: disable the CLI by default
This is unfortunate but master's flash size is over the APM2 limit
2014-03-05 12:03:56 +09:00
Randy Mackay
4f963e7795 Copter: move report_compass out of the CLI
This function is also used by compassmot.  Having it strictly part of
the CLI causes a compile error when the CLI is disabled
2014-03-05 12:01:45 +09:00
Randy Mackay
00f9843e40 Copter: remove CLI tests for gps, logging, radio
Required to shrink the firmware down so that it can fit on the APM2
boards
2014-03-05 11:44:09 +09:00
Randy Mackay
fc85228d09 Copter: remove CLI set
Frees about 1k of flash
2014-03-04 22:23:57 +09:00
Randy Mackay
3a934357e9 Copter: remove unused reset_land_detector 2014-03-04 22:23:55 +09:00
Randy Mackay
c56f521897 Copter: ch6 tuning of RC_FEEL_RP 2014-03-04 22:23:53 +09:00
Randy Mackay
e89600afe3 Copter: integrate smoothing gain into flight modes 2014-03-04 22:23:52 +09:00
Randy Mackay
3910ab807f Copter: replace input filtering with smoothing gain 2014-03-04 22:23:50 +09:00
Randy Mackay
429e8d5e50 Copter: integrate AttControl feel param 2014-03-04 22:23:49 +09:00
lthall
a9db399f60 Copter: integrate AttControl input shaping 2014-03-04 21:52:20 +09:00
Andrew Tridgell
86fa82f767 Copter: only send GPS2_RAW when we have a 2nd GPS 2014-03-03 07:05:47 +11:00
Andrew Tridgell
3de574e5dc Copter: disable GPS2 in HIL 2014-02-27 08:16:20 +11:00
Andrew Tridgell
37394b30ee Copter: added support for 2nd GPS 2014-02-26 09:40:29 +11:00
Andrew Tridgell
2fcbdc4056 Copter: pass fix type to gps->setHIL() 2014-02-25 21:11:10 +11:00
Andrew Tridgell
ffcc77a21f Copter: fix for HIL API change 2014-02-23 08:18:20 +11:00
Randy Mackay
d992483bf5 Copter: add EKF params to full param list 2014-02-21 13:51:22 +09:00
Randy Mackay
797212c7ab Copter: remove remnant of cli compassmot 2014-02-19 16:04:10 +11:00
Randy Mackay
2457dbf0cd Copter: more checks before starting compassmot
additional checks that copter is landed and that compassmot calibration
isn't already being performed.
Returns ACK to ground station as process begins
2014-02-19 16:04:03 +11:00
Andrew Tridgell
76b60a1a52 Copter: added compassmot over MAVLink
use the MAVLink interact code to allow for compassmot over MAVLink

Pair-Programmed-With: Randy Mackay <rmackay9@yahoo.com>
2014-02-19 16:04:00 +11:00
Andrew Tridgell
a45d77f893 Copter: set the ahrs.set_armed() flag 2014-02-19 10:53:44 +11:00
Andrew Tridgell
0cbe64bc5e Copter: use Log_Write_Baro()
this gives the raw pressure and temperature, which is useful for
analysis, plus allows for more accurate log replay
2014-02-19 09:22:45 +11:00
Randy Mackay
fdae812814 Copter: DO_SET_ROI persists across waypoints
Users should add a DO_SET_ROI command with zero lat, lon and alt to
restore the yaw control to the default control (which is normally
look-at-next-wp)
2014-02-18 21:36:02 +09:00
Randy Mackay
bf68edd01c Copter: bug fix to 50hz logging rate
Caught by Emile Castelnuovo
2014-02-17 22:25:02 +09:00
Randy Mackay
d9b7559379 Copter: remove duplicate #define from APM_Config.h 2014-02-17 16:44:47 +09:00
Randy Mackay
4e1c51aa65 Copter: bug to disarm at end of mission 2014-02-17 16:43:49 +09:00
Andrew Tridgell
ce66314f40 Copter: fixed HIL build on PX4 2014-02-17 12:34:34 +11:00
proficnc
bbf5c11c8a Update Parameters.pde
Moved Disabled to the bottom of the drop-down box for selecting logging types.
This is to reduce the potential for someone to accidentally select Disabled when they intend on selecting Default.
2014-02-17 10:02:45 +11:00
Randy Mackay
00913ffe1b Copter: throttle rate to simple P controller
Saves at least 15bytes of RAM
2014-02-16 13:35:40 +11:00
Randy Mackay
9444ba7ea8 TradHeli: init roll/pitch input filter 2014-02-16 13:35:33 +11:00
Randy Mackay
b259510095 Copter: init roll/pitch input filters 2014-02-16 13:35:30 +11:00
Andrew Tridgell
9c66dd0d2c Copter: change to Compass::learn_offsets 2014-02-16 13:22:13 +11:00
Randy Mackay
aab9b30bf6 Copter: replace APM_PI with AC_P
Saves about 90bytes of RAM
2014-02-15 06:09:08 +11:00
Randy Mackay
3f10a84a2a Copter: remove accel calibration from cli
Also remove compass, flight mode, optical flow, radio and ch6 tuning
knob setup from cli to free up 3.5k of flash
2014-02-15 06:09:08 +11:00
Randy Mackay
3ccd1ad170 Copter: integrate AttControl method name changes 2014-02-15 06:09:08 +11:00
Randy Mackay
6880a6db80 TradHeli: integrate AttControl method name changes 2014-02-15 06:09:08 +11:00
lthall
7ed5080dc9 Copter: simplify get_angle_targets_for_reporting 2014-02-15 06:09:08 +11:00
lthall
41dcfae7c0 AC Acro and Sport: Angle limit code update 2014-02-15 06:09:08 +11:00
Andrew Tridgell
ebf6d47830 Copter: disable direct tuning, we need accessors for this 2014-02-15 05:48:24 +11:00
Andrew Tridgell
2fbdf7f718 Copter: fixed build for AHRS API changes 2014-02-15 05:48:22 +11:00
Andrew Tridgell
a8dc1be4de Copter: fixed non-EKF copter build 2014-02-15 05:48:21 +11:00
Randy Mackay
20989fd5e9 Copter: allow ch6 tuning of EKF 2014-02-15 05:48:20 +11:00
Andrew Tridgell
86afd13f12 Copter: use GPS AIRBORNE_4G 2014-02-15 05:48:17 +11:00
Andrew Tridgell
a112694a50 Copter: added AUX switch option for enable/disable EKF 2014-02-15 05:48:17 +11:00
Andrew Tridgell
5606e2f4a7 Copter: enabled EKF and SIMSTATE flash logging 2014-02-15 05:48:16 +11:00
Andrew Tridgell
6a9189a6a5 Copter: enable AHRS2 mavlink message 2014-02-15 05:48:16 +11:00
Andrew Tridgell
99b3517a47 Copter: use AP_InertialNav_NavEKF when available 2014-02-15 05:48:15 +11:00
Andrew Tridgell
686d1b9124 Copter: changes set_home_position() to setup_home_position() for Inav 2014-02-15 05:48:15 +11:00
Andrew Tridgell
c6e25483b4 Copter: use a common home with AHRS 2014-02-15 05:48:15 +11:00
Andrew Tridgell
9cc00d20eb Copter: fixed for removed DCM blowup counts 2014-02-15 05:29:48 +11:00
Andrew Tridgell
79a29d12f2 Copter: fixed build for new AHRS API 2014-02-15 05:29:47 +11:00
Andrew Tridgell
af5a3dff93 Copter: enable use of AHRS_NavEKF 2014-02-15 05:29:47 +11:00
Andrew Tridgell
24f2ac20de Copter: removed HIL_MODE_ATTITUDE
this really can't work any more, as AHRS can't support it
2014-02-15 05:29:46 +11:00
Andrew Tridgell
644bf71f56 Copter: fixed build for InertialNav change 2014-02-15 05:29:46 +11:00
Randy Mackay
006cf58b2d Copter: fix merge error for g.angle_max 2014-02-15 05:27:51 +11:00
Randy Mackay
5e8fede19e Copter: comment fix to Attitude.pde 2014-02-15 05:27:50 +11:00
Randy Mackay
aa79e22ce0 Drift: bug fix for throttle 2014-02-15 05:27:50 +11:00