setting the parameter to 1 causes the following issues:
- the GPS may not have vertical velocity at the time the parameter
set happens, but may get it later when the GPS is fully configured
- we may switch between GPS modules which do/don't have vertical
velocity
- the user may download parameters after the set(1), and end up with
incorrect parameters they may later load onto the vehicle,
permanently disabling use of vertical velocity
also allows using ExtNav alt when not using it for XY position
removes redundant and incorrect setting of activeHgtSource from ExtNav
which was always being overwritten by the correct value later in selectHeightForFusion
Clarifies use of EK3_RANGE_USE_HGT and EK3_ALT_SOURCE parameters to control range finder use.
Setting EK3_RNG_USE_HGT to a positive number to enable automatic switching between the primary height source (baro or GPS) and range finder should be disabled if any primary height source other than Baro or GPS is selected via the EK3_ALT_SOURCE parameter.
AP_NavEKF3: Add emergency yaw reset using a Gussian Sum Filter estimate
AP_NavEKF3: Reduce default minimum GPS velocity noise for Copters
Enables fail-safe to be set with more sensitivity and improves tracking accuracy.
Origin values were set using typical GPS performance for receivers on sale 6 years ago. Receiver performance has improved since then.
AP_NavEKF3: Prevent constant mag anomaly yaw resets
Prevents constant magnetic anomaly induced resets that can be triggered when flying with vehicle generated magnetic interference.
Allows for two resets per takeoff. Allowance for two resets is required, becasue a large ground based magnetic yaw anomaly can cause a sufficiently large yaw innovation that two resets in close succession are required.
AP_NavEKF3: Add option to fly without magnetometer
AP_NavEKF3: Rework emergency yaw reset logic
Use a separate external accessor function to request the yaw reset.
Allow reset requests to remain active for a defined period of time.
Tidy up reset function to split out accuracy check.
AP_NavEKF3: Fix vulnerability to lane switch race condition
Prevents the situation where a lane switch results in a lane being selected that does not have the correct yaw. This can occur if the primary lane becomes unhealthy before the external failsafe monitor has time to react.
AP_NavEKF3: Fix EKF_MAG_CAL = 6 behaviours
Fix bug causing the yaw alignment to be performed at startup before the GSF had a valid estimate.
Fix bug causing emergency yaw message to be output for a normal reset.
Fix vulnerability to reported negative yaw variance.
Remove duplicate timer checks.
AP_NavEKF3: Update EK3_MAG_CAL documentation
AP_NavEKF3: Relax yaw gyro bias convergence check when not using mag
AP_NavEKF3: Reduce yaw drift in hover with no yaw sensor
Uses the GSF yaw estimate if available which is better than the EKF's own yaw when no yaw sensor is available.
when GPS primary switches we were using a position which had not been
corrected for antenna offset. This was used for calculating the reset
for sensor change.
This fixes that (trivial fix) and also fixes a similar issue on
position reset
when on the ground without a position source we would disable the
innovation gate for the barometer. This meant that a single (or small
number of) really bad baro readings would be fused into the EKF,
causing it to destabilise
Fixes#11903
this forces the EKF origin to the GPS alt on a height datum reset if
we have GPS lock. If we don't do this then the reported AMSL alt will
drift over time away from the GPS alt when we reset while on the
ground
All Kalman gain calculations now explicity set gains for deactivated states to zero.
Previous use of loops to set gains to zero have been replaced with more efficient memset operations.
Fix rounding error bug preventing state from updating after initial convergence.
Decouple GPS reference height from published EKf origin height.
Add bitmask parameter to control update and publishing of GPS reference height.
If the GPS receiver selection changes and we are using GPS for height, the vertical position will be reset to the new GPS height measurement.
correct output observer history when doing a GPS height reset
Enables the horizontal speed at which we switch from range finder to alternate to be adjusted.
Does not switch from range finder to alternate based on speed when speed estimate is invalid.
AP_NavEKF3: Implement same maths as PX4/ecl EKF
Replace attitude vector states with quaternions
Remove gyro scale factor states
Add XY accel delta velocity bias estimation
Initial tuning
Add GPS body frame offset compensation
AP_NavEKF3: Fix bugs and consolidate aiding switch logic
Switching in and out of aiding modes was being performed in more than one place and was using two variables.
The reversion out of GPS mode due to prolonged loss of GPS was not working.
This consolidates the logic and ensures that PV_AidingMode is only changed by the setAidingMode function.
AP_NavEKF3: prevent multiple fusion mode changes per filter update
AP_NavEKF3: Update tuning defaults
AP_NavEKF3: Fix bug causing switching in and out of aiding
If the GPS receiver was disconnected and no data received, then then the gpsGoodToAlign check did not get a chance to run and becasue it was previously true the EKF would switch back into aiding.
This prevents this by ensuring that gpsGoodToAlign defaults to false when the check is not being performed.
An additional check has also been dded to ensure that there is GPS data to fuse before we declare ready to use GPS.
AP_NavEKF3: Fix bug preventing planes recovering from bad magnetometers
This bug created a race condition whereby if the EKF had to reset the yaw to the GPS ground course to recover from a bad magnetometer, the new heading could be over-written by the bad magnetic heading when the plane reached the height for the scheduled reset.
AP_NavEKF3: Improve switch-over to backup magnetometer
When switching over to a back up magnetometer, ensure that the earth field estimate are reset. Otherwise mag earth field estimates due to the previous failed mag could cause data from the new mag to be rejected.
AP_NavEKF3: enable automatic use of range finder height
AP_NavEKF3: Fix bug in handling of invalid range data
AP_NavEKF3: Fix height drift on ground using range finder without GPSAP_NavEKF3:
AP_NavEKF3: Handle yaw jumps due to core switches
AP_NavEKF3: Enable simultaneous GPS and optical flow use
AP_NavEKF3: fix console status reporting
AP_NavEKF3: send messages to mavlink instead of console
This allows the GCS to better handle the display of messages to the user.
AP_NavEKF3: replace deprecated function call
AP_NavEKF3: Compensate for sensor body frame offsets
AP_NavEKF3: Fix bug in median filter code
AP_NavEKF3: save some memory in the position offsets in EKF3
We don't need to copy that vector3f for every sample. A uint8_t does the job
AP_NavEKF3: Add fusion of range beacon data
AP_NavEKF3: Bring up to date with EKF2
AP_NavEKF3: Misc range beacon updates
AP_NavEKF3: Add mising accessors
AP_NavEKF3: remove duplicate include
AP_NavEKF3: Prevent NaN's when accessing range beacon debug data
AP_NavEKF3: Update range beacon naming
AP_NavEKF3: updates
AP_NavEKF3: miscellaneous changes
AP_NavEKF3: misc updates
AP_NavEKF3: misc range beacons updates
AP_NavEKF3: add missing rover default param
Andrew Tridgell
Randy Mackay
chobits
Peter Barker
Paul Riseborough
Dr.-Ing. Amilcar do Carmo Lucas
priseborough
Paul Riseborough
Daniel Magree
Michael du Breuil
Arjun Vinod
Tom Pittenger
murata
Jonathan Challinger