Fix rounding error bug preventing state from updating after initial convergence.
Decouple GPS reference height from published EKf origin height.
Add bitmask parameter to control update and publishing of GPS reference height.
If the GPS receiver selection changes and we are using GPS for height, the
vertical position will be reset to the new GPS height measurement.
correct output observer history when doing a GPS height reset
The EK2_RNG_USE_HGT parameter sets the height (expressed as a percentage of the maximum range of the range finder as set by the RNGFND_MAX_CM parameter) below which the range finder will be used as the primary height source when the vehicle is moving slowly.
When using a height reference other than GPS, the height datum can drift due to air pressure changes if using baro, or due to terrain height changes if using range finder as the primary height source. To ensure that a consistent height datum is available when switching between altitude sources, the WGS-84 height estimate of the EKF's local positi norigin is updated using a
single state Bayes estimator,
If rngfinder or gps height data is lost whilst being used, there will be a fall-back to baro data.
Switching in and out of aiding modes was being performed in more than one place and was using two variables.
The reversion out of GPS mode due to prolonged loss of GPS was not working.
This consolidates the logic and ensures that PV_AidingMode is only changed by the setAidingMode function.
Splits in-flight yaw alignment completed status into separate yaw and magnetic field flags.
Reduce the number of places where decisions to perform a yaw and field reset are made.
Don't perform a reset unless there is is data in the buffer
Don't use 3-axis fusion if the field states still need to be reset.
When starting 3-axis fusion request a reset if not previously performed.
Ensure magnetometer and GPs heading resets are alwasy perfomred with data at teh correct time horizon.
This removes a legacy design concept that is no longer required in this filter implementation. Planes will not be armed without EKF aiding and the proposed copter throw mode also requires EKF aiding to be operating.
The other problem with interrupting fusion during the launch is it doesn't reduce the corrections, it just delays them as wen the launch completes, the EKF inertial position estimate is still moving still moved and the corrections are therefore just delayed by the short launch interval.
Thank you to OXINARF for picking up the inconsistency with the previous logic
Change to user adjustable fusion of constant position (as per legacy EKF) instead of constant velocity.
Enable user to specify use of 3-axis magnetometer fusion when operating without aiding.
Don't allow gyro scale factor learning without external aiding data as it can be unreliable
Eliminate the use of horizontal position states during non-aiding operation to make it easier to tune.
Explicitly set the horizontal position associated Kalman gains to zero and the coresponding covariance entries to zero after avery fusion operation.
Make the horizontal velocity observation noise used during non-aiding operation adjustable.
Use a fixed value of velocity noise during initial alignment so that the flight peformance can be tuned without affecting the initial alignment.
The non-GPS mode was not being activated for small height gains - eg indoor flight.
The incorrect innovation consistency check was being applied to the synthetic velocity observations.
The problem with using min() and max() is that they conflict with some
C++ headers. Name the macros in uppercase instead. We may go case by
case later converting them to be typesafe.
Changes generated with:
git ls-files '*.cpp' '*.h' -z | xargs -0 sed -i 's/\([^_[:alnum:]]\)max(/\1MAX(/g'
git ls-files '*.cpp' '*.h' -z | xargs -0 sed -i 's/\([^_[:alnum:]]\)min(/\1MIN(/g'
GPS height has been added as a measurement option along with range finder and baro
Selection of the height measurement source has been moved into a separate function
Each height source is assigned its own measurement noise
If GPS or baro alt is not able to be used, it reverts to baro
When baro is not being used, an offset is continually calculated which enables a switch to baro without a height step.
Down-sample the IMU and output observer state data to 100Hz for storage in the buffer.
This reduces storage requirements for Copter by 75% or 6KB
It does not affect memory required by plane which already uses short buffers due to its 50Hz execution rate.
This means that the EKF filter operations operate at a maximum rate of 100Hz.
The output observer continues to operate at 400Hz and coning and sculling corrections are applied during the down-sampling so there is no loss of accuracy.
Apply filtering to baro innovation check and and don't apply innovation checks once aiding has commenced because GPS and baro disturbances on the ground and during launch could generate a false positive
Extended GPS loss can result in the earth field states becoming rotated and making it difficult for the EKF to recover its heading when GPS is regained.
During prolonged GPS outages, the position covariance can become large enough to cause the reset function to continually activate. This is fixed by ensuring that position covariances are always reset when the position is reset.
The innovation variance was being used incorrectly instead of the state variance to trigger the glitch reset.
This sets the fusion of the synthetic position and velocity to occur at the same time as the barometer
This makes filter tuning more consistent between GPS and non-GPS useage
priseborough
Jonathan Challinger
Randy Mackay
Francisco Ferreira
Dr.-Ing. Amilcar Do Carmo Lucas
Andrew Tridgell
Mathieu OTHACEHE
Ricardo de Almeida Gonzaga
Lucas De Marchi
Siddharth Bharat Purohit
Paul Riseborough