use regulated time for frequency noise to avoid spurious harmonics
SITL sensors must be true separate instances
don't compile in FFT structures if DSP disabled
FFT windows can be dynamically allocated
add harmonic notch dynamic tracking mode
unwind gyro window allocation in the case of failure
allow access to harmonic notch harmonics
this we ensures we get new data for all active IMUs on each loop,
rather than sometimes returning with some IMUs not having data.
This matters as not having a sample on an IMU for a single loop can
cause an EKF IMU failover, which will degrade the learned bias
variances
The issue is usually only seen under high load, such as requesting a
loop rate beyond what the hardware is capable of
https://github.com/ArduPilot/ardupilot/issues/11346
Allocate a notch filter per-IMU.
Update the notch filters in the backend at the sensor sample rate.
Allow raw logging of post-filtered gyro and accel values.
AP_InertialSensor: add parameters for push-to-log interval and count
AP_InertialSensor: rename BAT_RAW to BAT_OPT
This becomes a bitmask of options for the BatchSampler
AP_InertialSensor: rename 'fast sample' to 'sensorrate sample'
AP_InertialSensor: const sensor-rate filter method
AP_InertialSampler: remove hard-coding of sample rate multiplier
AP_InertialSensor: use parameter to enable/disable sensor-rate logging
AP_InertialSensor: use a parameter to control sensor-rate logging
AP_InertialSensor: allow backends to override sensor data multiplier
e.g. some accelerometers are sensitive over wider ranges than the default 16G
AP_Inertialsensor: correct sample rate multiplier
this allows for only a specified subset of IMUs to be probed, so you
can disable IMUs that aren't needed.
The back corresponds to bits in the order the IMUs are normally probed
on the board
See discussion here:
https://github.com/ArduPilot/ardupilot/issues/7331
we were getting some uninitialised variables. While it only showed up in
AP_SbusOut, it means we can't be sure it won't happen on other objects,
so safest to remove the approach
Thanks to assistance from Lucas, Peter and Francisco
FIFO sensors produce data at a well known rate, but samples come in
bunches, so we can't use the system clock to calculate deltaT.
non-FIFO sensors produce data when we sample them, but that rate is
less regular due to timing jitter.
For FIFO sensors this changes makes us use a learned sample rate,
which allows for different clock speeds on sensor and system board.
For non-FIFO sensors we use the system clock to measure deltaT
the overall effect is a fix for sensors that produce samples at other
than the claimed datasheet rate.
this allows enable/disable of fast sampling per IMU, making
experimentation easier.
It also fixes the fast sampling to always average over 8 samples, and
fixes the 9250 to use the correct accumulator when not doing fast
sampling
This allows each sensor to be uniquely identified in the system by using
either the index inside the backend or for those that use the Device
interface, to use the bus type, location, and device id.
We leave 16-bit for each sensor to be able to change its own
identification in future, which allows them to be changed in an
incompatible manner forcing a re-calibration.
When we are initializing the gyro and then saving the calibration we are
also saving the calibration values for the accelerometers. Right now
this is non-problematic, but we want to check that the ID of the
accelerometer corresponds to the ID of the sensor detected. If we also
save accel calibrations we would actually override the ID of the
accelerometer.
Rename the method to _save_gyro_calibration() and save only on gyro
values.
We only leave the parameter there for backward-compatibility. However
product id on the inertial sensor is not much useful since it's only
kept for the first instance.
A better implementation per-gyro and per-accel is needed in order to
avoid problems with sensors taking the offsets configured for another
sensor.
RC_Channel: To nullptr from NULL.
AC_Fence: To nullptr from NULL.
AC_Avoidance: To nullptr from NULL.
AC_PrecLand: To nullptr from NULL.
DataFlash: To nullptr from NULL.
SITL: To nullptr from NULL.
GCS_MAVLink: To nullptr from NULL.
DataFlash: To nullptr from NULL.
AP_Compass: To nullptr from NULL.
Global: To nullptr from NULL.
Global: To nullptr from NULL.
Michael du Breuil
Andy Piper
Andrew Tridgell
Siddharth Purohit
Tom Pittenger
Peter Barker
Jacob Walser
Lucas De Marchi
murata
priseborough
Mathieu OTHACEHE