Mirror
/
ardupilot
mirror of https://github.com/ArduPilot/ardupilot
5
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity
46,299 Commits 70 Branches 507 Tags 665 MiB
Commit Graph

25337 Commits

Author SHA1 Message Date
Andy Piper d41c92d317 AP_HAL_ChibiOS: don't overwrite fault handler data, register forced faults 2021-01-27 19:13:18 +11:00
Andy Piper 20d928a86a AP_HAL_ChibiOS: don't share DMA on OmnibusNanoV6 for Flash SPI 2021-01-27 19:04:49 +11:00
Andy Piper 873d35acd9 AP_HAL_ChibiOS: bi-directional dshot for MatekH743 2021-01-27 18:58:38 +11:00
Andy Piper 877dde4736 AP_HAL_ChibiOS: on BeastF7 share TIM3 UP/CH and give flash SPI dedicated channel 2021-01-27 18:54:43 +11:00
Andy Piper 2395018000 AP_BLHeli: don't log invalid bi-dir dshot values as they are never used 2021-01-27 18:54:10 +11:00
Andy Piper 9249b73e8b AP_HAL_ChibiOS: correctly allow mixing of bidir and non-bidir channels 2021-01-27 18:49:15 +11:00
Andy Piper 2823fa7245 AP_HAL_ChibiOS: never write bytes that have not been erased on H7 
Be more careful about flash failure conditions on H7
 2021-01-27 18:30:36 +11:00
Andy Piper 78735a946e AP_HAL_ChibiOS: allow STM32_FLASH_DISABLE_ISR for H7 2021-01-27 18:30:36 +11:00
Andrew Tridgell 155de6d2bc HAL_ChibiOS: fixed build of AP_Periph on H7 2021-01-27 18:24:03 +11:00
Andrew Tridgell 0535c4f592 AP_InertialSensor: default TMAX to 70 
if user forgets to set this then better to just timeout rather than
calibrating over a small range
 2021-01-27 09:49:35 +11:00
Andrew Tridgell 9861a02c60 HAL_ChibiOS: save INS_ACC*ID persistent parameters 
this enables full factory accelerometer calibration, so the user is
not required to run an accelcal, even if they change vehicle type
 2021-01-27 09:49:35 +11:00
Andrew Tridgell bdb364d461 AP_InertialSensor: save the accelerometer ID parameters 
this is needed for factory accel cal
 2021-01-27 09:49:35 +11:00
Andrew Tridgell 87528f47c8 AP_IOMCU: prevent internal error on bootloader flash 
when we flash the bootloader on boards with an IOMCU we expect a long
delay as the CPU stops during the flash
 2021-01-27 09:49:35 +11:00
Andrew Tridgell 6163659887 AP_HAL: prevent a single bad transfer causing an IMU to be marked unhealthy 
This is a response to this issue:
https://discuss.ardupilot.org/t/gyro-problem-after-waypoint-log-analisys

The 2nd gyro went bad with a large offset. Then the first gyro was
marked unhealthy, forcing the EKF to switch to the 2nd gyro. That
resulted in a crash.

I think the SPI bus was getting bad transfers and the register check
code happened to get a bad transfer, thereby marking the first gyro
unhealthy

This change ensures we only fail the register check if two transfers
in a row are bad. This makes it much less likely that a noisy bus will
lead to an unhealthy gyro
 2021-01-27 09:47:55 +11:00
Iampete1 ebfe593e38 AP_Scripting: add example script setting up a custom MotorMatrix 2021-01-26 11:07:36 +09:00
Iampete1 5c397d4674 AP_Scripting: add MotorMatrix bindings 2021-01-26 11:07:36 +09:00
Iampete1 fca6f7027b AP_Motors: allow Matrix config from scripting 2021-01-26 11:07:36 +09:00
Peter Hall d0e1e85b9e AP_Motors: add get_frame_mav_type 2021-01-26 11:07:36 +09:00
Randy Mackay f6cb0819ef AP_NavEKF3: pre_arm_check may skip position checks 2021-01-26 10:46:49 +11:00
Randy Mackay 8ecac27777 AP_NavEKF_Source; pre_arm_check may skip position checks 2021-01-26 10:46:49 +11:00
Randy Mackay 62932f884f AP_AHRS: pre_arm_check may skip position checks 2021-01-26 10:46:49 +11:00
Andrew Tridgell 1716fcf995 GCS_MAVLink: fixed valgrind errors with AP_Param::ParamToken 2021-01-26 10:43:09 +11:00
Andrew Tridgell ac35867c17 AP_Param: fixed valgrind errors with AP_Param::ParamToken 2021-01-26 10:43:09 +11:00
Andrew Tridgell 12b93e2922 AP_OSD: fixed valgrind errors with AP_Param::ParamToken 2021-01-26 10:43:09 +11:00
Andrew Tridgell 6c684538d3 AP_Param: greatly speed up param download with disabled parameters 
allows fast skip over disabled subgroups. This removes a long delay
with param download on a MatekF405-STD where the final parameters
associated with the OSD took 80ms to fetch, causing a long loop delay
 2021-01-26 10:43:09 +11:00
Peter Barker d426d8e1f8 AP_GPS: use ground_course in preference to ground_course_cd 2021-01-26 10:22:28 +11:00
Peter Barker 358069df24 AP_AHRS: use ground_course in preference to ground_course_cd 2021-01-26 10:22:28 +11:00
WillyZehnder 2e2ec79992 RC_Channel: reserve AUX_FUNC for MISSION_RELATIVE 2021-01-26 10:14:11 +11:00
Andrew Tridgell 2843cfa42d AP_InertialSensor: use mavlink statustext for cal info 2021-01-25 16:24:50 +11:00
Andrew Tridgell b542f947f7 AP_InertialSensor: don't mark accels as calibrating during trim 
we need the accels with offsets applied when doing accel trim
 2021-01-25 16:24:50 +11:00
Andrew Tridgell e908a996af AP_InertialSensor: support SIM_ACC_TRIM 
and cleanup vector maths
 2021-01-25 16:24:50 +11:00
Andrew Tridgell 7292b4f260 SITL: added SIM_ACC_TRIM_{X,Y,Z} for simulating IMU trim 
this will enable an autotest for AHRS trim
 2021-01-25 16:24:50 +11:00
Andrew Tridgell ddc4d08e8f AP_NavEKF3: make drag fusion optional 2021-01-24 11:56:52 +11:00
Andrew Tridgell 1ccda938cb AP_NavEKF3: make external navigation optional 2021-01-24 11:56:52 +11:00
Andrew Tridgell 8da511f039 AP_NavEKF3: make body odomotry build depend on vehicle type 
saves about 11k of flash
 2021-01-24 11:56:52 +11:00
E Thomas 2ee052b36e AP_GPS: Made GPS_DISABLE prevent last_fix_time_ms updates 2021-01-23 17:25:00 +11:00
Peter Barker ade1c487d8 AP_Logger: remove default reason argument for Write_Mode 
All callers now supply this
 2021-01-22 17:27:26 +11:00
Leonard Hall 25fff17e48 AC_AttitudeControl: constify some local variables 2021-01-22 14:22:18 +09:00
Peter Barker 3582b69e9c AP_NavEKF3: remove getFilterTimeouts access methods 2021-01-22 13:04:36 +11:00
Peter Barker 445a461f12 AP_NavEKF2: remove getFilterTimeouts access methods 2021-01-22 13:04:36 +11:00
Peter Barker 401cccca19 AP_NavEKF2: correct description on NKF3.SVT 2021-01-21 21:26:17 +11:00
Peter Barker b3bacdd33c AP_NavEKF3: remove internal-only getTiltError method 2021-01-21 21:26:17 +11:00
Peter Barker dddb285209 AP_NavEKF2: remove internal-only getTiltError method 2021-01-21 21:26:17 +11:00
Peter Barker 5ad0ac6727 AP_NavEKF3: remove unused getAccelNED method 2021-01-21 21:26:17 +11:00
Peter Barker 6b60bae068 AP_NavEKF2: remove unused getAccelNED method 2021-01-21 21:26:17 +11:00
Peter Barker e32ca819fc GCS_MAVLink: mark results as unused 2021-01-21 20:41:17 +11:00
Peter Barker 60d0b0f07c AP_AHRS: add WARN_IF_UNUSED to some getters 2021-01-21 20:41:17 +11:00
Andrew Tridgell 6c8a57c2d7 AP_InertialSensor: review fixes 2021-01-21 13:09:21 +11:00
Andrew Tridgell 3ff71c7814 AP_InertialSensor: changes from review feedback 2021-01-21 13:09:21 +11:00
Andrew Tridgell b12a663f7a AP_InertialSensor: apply accel scaling 2021-01-21 13:09:21 +11:00
Andrew Tridgell 9febcc0f98 SITL: added accel scaling parameters 2021-01-21 13:09:21 +11:00
Andrew Tridgell 73ddde3629 AP_InertialSensor: changes for new SITL IMU params 2021-01-21 13:09:21 +11:00
Andrew Tridgell b5089580a9 SITL: cleanup IMU parameters 
allow for biases per IMU
 2021-01-21 13:09:21 +11:00
Andrew Tridgell 5e60fac37e AP_InertialSensor: remove unused variable 2021-01-21 13:09:21 +11:00
Andrew Tridgell 285b53fe07 AP_InertialSensor: use vector polyfit 
this reduces memory usage
 2021-01-21 13:09:21 +11:00
Andrew Tridgell a1fb0592a9 AP_Math: specialise polyfit for vectors 
this is needed to get the precision good enough for wide temperature
ranges when summing the resulting polygon coefficients
 2021-01-21 13:09:21 +11:00
Andrew Tridgell c8aaceb6ac AP_LeakDetector: remove warning message on all non-sub builds 
pointless pragma
 2021-01-21 13:09:21 +11:00
Andrew Tridgell d0d480e858 AP_Compass: fixed matrix inverse for new name 2021-01-21 13:09:21 +11:00
Andrew Tridgell 8278a8a00b AP_AccelCal: rename from review feedback 2021-01-21 13:09:21 +11:00
Andrew Tridgell 2e2ccb40b2 AP_AccelCal: fixed inverse matrix call for new name 2021-01-21 13:09:21 +11:00
Andrew Tridgell 999268cbba AP_Math: fixup matrix algorithms to be in cpp file 
this fixes an issue where optimize O2 was forced on any file that
included AP_Math.h. It also fixes the test suite for matrix_alg, and
fixes the type handling to be consistent
 2021-01-21 13:09:21 +11:00
bugobliterator 3b3e2c01f8 AP_Math: templatize matrix_alg methods 2021-01-21 13:09:21 +11:00
Andrew Tridgell ffe20f7958 AP_InertialSensor: use a fixed reference temperature of 35C 
this allows us to timeout the calibration when the temperature stops
rising as the polynomial no longer depends on the maximum temperature
 2021-01-21 13:09:21 +11:00
Andrew Tridgell dc58b0b950 AP_InertialSensor: changes from review feedback 
thanks Sid!
 2021-01-21 13:09:21 +11:00
Andrew Tridgell 9561f24c0e AP_Filesystem: added @SYS/persistent.parm 2021-01-21 13:09:21 +11:00
Andrew Tridgell 5ed19c764e HAL_ChibiOS: expose load_persistent_params for @SYS 2021-01-21 13:09:21 +11:00
Andrew Tridgell 1680e6e7d6 AP_HAL: expose load_persistent_params() in hal.util 2021-01-21 13:09:21 +11:00
Andrew Tridgell c9a83c8127 AP_InertialSensor: added INS_TCAL_OPTIONS 
make persistent params optional, and allow save of accelcal
 2021-01-21 13:09:21 +11:00
Andrew Tridgell 5c823debc0 HAL_ChibiOS: support saving persistent parameters to bootloader sector 
when we flash the bootloader we can save key peristent parameters to
the end of the bootloader sector, allowing them to persistent across
changes of firmware type

This allows for factory temperature calibration
 2021-01-21 13:09:21 +11:00
Andrew Tridgell 504f500fae AP_Common: added get_writeable_string to ExpandingString 2021-01-21 13:09:21 +11:00
Andrew Tridgell 1ddc21c9bb AP_InertialSensor: support saving tempcal params persistently 2021-01-21 13:09:21 +11:00
Andrew Tridgell 8caea96ab1 AP_InertialSensor: start auto-learning at boot 
This makes it easier to setup the params. The ENABLE=2 value only
takes effect at boot
 2021-01-21 13:09:21 +11:00
Andrew Tridgell 7cb7ad3636 AP_InertialSensor: fixed build error 2021-01-21 13:09:21 +11:00
Andrew Tridgell 2e9f61fe49 AP_InertialSensor: fixed IMU index display in msgs 
start at 1 for users
 2021-01-21 13:09:21 +11:00
Andrew Tridgell d5b511f4a0 AP_InertialSensor: fixed start timer for temperature in SITL 
when we are doing an autotest we want the temperature to start
climbing when we first set SIM_IMUT_FIXED=0
 2021-01-21 13:09:21 +11:00
Andrew Tridgell 30e55d8dfc AP_InertialSensor: cope with user changing TMAX while calibrating 2021-01-21 13:09:21 +11:00
Andrew Tridgell 68526262b7 AP_Arming: don't allow arming during IMU temp cal 2021-01-21 13:09:21 +11:00
Andrew Tridgell e2e97c67ce AP_InertialSensor: catch user attempt to change TMAX during cal 2021-01-21 13:09:21 +11:00
Andrew Tridgell 73e53369e8 AP_Notify: added notify events for temperature calibration 2021-01-21 13:09:21 +11:00
Andrew Tridgell 3fb720354d AP_InertialSensor: added notify events for temperature calibration 2021-01-21 13:09:21 +11:00
Andrew Tridgell cc3579ea5d AP_InertialSensor: change TCAL sampling to be even in temperature 2021-01-21 13:09:21 +11:00
Andrew Tridgell cf47c19c0d Filter: fixed low pass 2p filter to auto-init 
this prevents the init to zero for temperature filters
 2021-01-21 13:09:21 +11:00
Andrew Tridgell 4495414d05 Filter: added reset with value to LowPassFilter2p 2021-01-21 13:09:21 +11:00
Andrew Tridgell fc0f8b990a AP_InertialSensor: added online learning of temp cal 
use INS_TCAL1_ENABLE=2 to start learning
 2021-01-21 13:09:21 +11:00
Andrew Tridgell 64d9f43d94 AP_Math: added polygon fitting code 2021-01-21 13:09:21 +11:00
Andrew Tridgell 720f9a1de0 AP_Math: cleanup maths functions 
use class template instantiation, and cleanup const in matrix code
 2021-01-21 13:09:21 +11:00
Andrew Tridgell 6f6f89e5aa AP_InertialSensor: enable temperature sensor on LSM9DS0 
this allows for temperature calibration of the LSM303D in CubeBlack
and Pixhawk1
 2021-01-21 13:09:21 +11:00
Andrew Tridgell 0c156e324b AP_Compass: enable temperature on lsm303d 2021-01-21 13:09:21 +11:00
Andrew Tridgell c0ba7c29ca SITL: use TCal class for temp adjustment in SITL 2021-01-21 13:09:21 +11:00
Andrew Tridgell 4bdf506d10 AP_InertialSensor: apply 1e-5 scale factor 
this keeps the params in a reasonable range for parameter editors
 2021-01-21 13:09:21 +11:00
Andrew Tridgell 0f6f6bac6b AP_InertialSensor: expose TCal class for use in SITL 2021-01-21 13:09:21 +11:00
Andrew Tridgell 7921e042f1 AP_InertialSensor: added IMU temperature calibration support 
this adds parameters that can be setup by an external script for
compensating for temperature variation in gyros and accels using a 3rd
order polynomial
 2021-01-21 13:09:21 +11:00
Andrew Tridgell 580cd143b8 AP_AccelCal: added active() method 2021-01-21 13:09:21 +11:00
Siddharth Purohit f53d80374b SITL: fix build for macos systems 2021-01-21 13:09:21 +11:00
Peter Barker e58d2ecf2f GCS_MAVLink: add mavlink command option to create a 250ms long loop 2021-01-21 11:35:57 +11:00
Andrew Tridgell d81c2ee407 HAL_ChibiOS: allow for some embedded parameters on AP_Periph builds 2021-01-21 06:19:46 +11:00
murata fd91cb03b4 SITL: Change the Kelvin value to a defined name 2021-01-20 20:27:19 +11:00
bugobliterator 8b90eb23e0 AP_HAL_ChibiOS: distcc doesn't like lst generation commands 2021-01-20 19:21:14 +11:00
Randy Mackay 031be010ac AC_AttitudeControl: tailsitter sets target rates more efficiently 2021-01-20 18:21:12 +11:00
Leonard Hall 4e2c7880c5 AC_Avoidance: use AP_Math control functions 2021-01-20 18:19:40 +11:00
Leonard Hall e2308e9414 AC_Loiter: use AP_Math control tools common functions 2021-01-20 18:19:40 +11:00
Randy Mackay 6320338771 AC_PosControl: use AP_Math control functions 2021-01-20 18:19:40 +11:00
Leonard Hall 1129a3fd59 AC_AttitudeControl: use AP_Math control functions 2021-01-20 18:19:40 +11:00
Leonard Hall 1e38440c83 AP_Math: add control common functions 2021-01-20 18:19:40 +11:00
Andy Piper 2fadcf6ba0 AP_HAL_ChibiOS: handle UP/CH channel sharing on H7 correctly 2021-01-20 18:15:17 +11:00
Andy Piper 9e641a32ad AP_HAL_ChibiOS: don't share flash SPI on BeastH7 and compile with -Os 2021-01-20 18:12:57 +11:00
Andy Piper 2b885cd79f AP_HAL_ChibiOS: ensure that serial LED setup goes via an intermediate buffer 
protect serial LED buffer transfers with mutex
protect serial LED buffer size with mutex
prevent serial LED interactions before rcout is ready
allocate a serial led buffer per channel that needs it
setup clock mask when needed
 2021-01-20 18:10:18 +11:00
yaapu ecfcd98f8a AP_RCTelemetry: apply a 5s hysteresis to RF mode changes and rate reporting 2021-01-20 18:06:24 +11:00
Andy Piper 23158480c7 AP_RCTelemetry: calculate CRSF custom frame support correctly 2021-01-20 18:06:24 +11:00
Andy Piper 39219451bd AP_RCTelemetry: detect CRSF tracer RX and switch to 250Hz high speed telemetry 2021-01-20 18:06:24 +11:00
Andy Piper f6a2d20579 AP_RCProtocol: add tracer 250Hz mode 2021-01-20 18:06:24 +11:00
yaapu 79640e5d94 RC_Channel: added support for passthrough telemetry over crossfire 2021-01-20 18:06:24 +11:00
yaapu 1c3b7d5ecd GCS_MAVLink: added support for passthrough telemetry over crossfire 2021-01-20 18:06:24 +11:00
yaapu 6b26a64f77 AP_Frsky_Telem: added support for passthrough telemetry over crossfire 2021-01-20 18:06:24 +11:00
yaapu 5ef20aec27 AP_RCProtocol: added support for passthrough telemetry over crossfire 2021-01-20 18:06:24 +11:00
yaapu 4933544489 AP_RCTelemetry: added support for passthrough telemetry over crossfire 2021-01-20 18:06:24 +11:00
Andrew Tridgell 9db0862d61 HAL_Linux: use nullptr for vnav rcinput 
this makes it clearer what is going on
 2021-01-20 13:49:26 +11:00
Michael du Breuil 15fd8480f8 AP_EFI: Correct a bad conversion from Kelvin to Celsius 
(was off by 0.15 degrees)
 2021-01-20 11:10:25 +11:00
Andrew Tridgell dff6a5bff9 HAL_Empty: allow return of last value in RCOutput 
this is needed for linux boards with no native RCOutput that use SBUS
out on a serial port to ensure they can display the servo values in
the GCS
 2021-01-20 10:06:45 +11:00
Andrew Tridgell 1ce77111e5 AP_AHRS: allow override of default EKF type 2021-01-20 10:06:45 +11:00
Andrew Tridgell 009cb8f62b HAL_Linux: setup RCIN for vnav 2021-01-20 10:06:45 +11:00
Andrew Tridgell a9f8c9517c AP_HAL: added vnav linux target 2021-01-20 10:06:45 +11:00
Andrew Tridgell 103d6c54e1 AP_ExternalAHRS: added vnav linux target 2021-01-20 10:06:45 +11:00
Peter Barker 933aba66f8 AP_HAL_SITL: avoid nullptr dereference in Replay 2021-01-19 15:15:35 +11:00
Peter Barker c0ea19e5c5 SITL: add test for maxbotixi2cxl 2021-01-19 11:20:47 +11:00
Peter Barker 78b49a2c35 AP_RangeFinder: maxbotix: use i2c-address parameter 2021-01-19 11:20:47 +11:00
Iampete1 9be19b0bfa AP_Scripting: add plane spesific quadplane in_vtol_mode binding 2021-01-19 11:18:10 +11:00
Iampete1 7de14f2e2f AP_Scripting: desc: update AP_Terrain depends 2021-01-19 11:18:10 +11:00
Iampete1 2a75432fa2 AP_Scripting: Generator: support depends 2021-01-19 11:18:10 +11:00
Pierre Kancir 30a4747898 GCS_MAVLink: send sim_state msg 2021-01-19 10:40:43 +11:00
Pierre Kancir c1f1208c89 SITL: add support for SIM_STATE msg 2021-01-19 10:40:43 +11:00
Andrew Tridgell d9dbcb17c4 AP_Math: enable constrain value with line numbers on all boards 2021-01-19 10:24:39 +11:00
Andrew Tridgell 5def8a64ab SITL: avoid negative current and voltage in flightaxis 
RealFlight9 will sometimes give meaningless negative values
 2021-01-19 10:21:35 +11:00
Andrew Tridgell 53326a08ed AP_DAL: add 10k to SITL memory available 
this is needed as the SITL data structures are larger than on STM32
due to pointer size. This means we sometimes fail to replay in SITL as
we refuse to allocate an EKF core
 2021-01-18 13:01:00 +11:00
bugobliterator c02c546077 AP_HAL_ChibiOS: add support for inline comments in hwdef.dat 2021-01-18 09:37:11 +11:00
bugobliterator 41693403e2 AP_HAL_ChibiOS: retain memory of past conflicts in dma_resolver 2021-01-18 09:37:11 +11:00
Randy Mackay 0cc9fd2b5d AP_AHRS_NavEKF: get_secondary_quat and position may return EKF3 value 2021-01-16 08:24:23 +09:00
Randy Mackay 1b3ad9cd8d AP_AHRS: use ekf3 by default 2021-01-16 08:24:23 +09:00
Randy Mackay 60633f5a7f AP_NavEKF2: disable ekf2 by default 2021-01-16 08:24:23 +09:00
Randy Mackay 4492e5024c AP_NavEKF3: enable ekf3 by default 2021-01-16 08:24:23 +09:00
Andrew Tridgell ed8d86e5e6 GCS_MAVLINK: support deliberate parameter corruption 2021-01-16 06:47:10 +11:00
Andrew Tridgell 6ca68bfba3 AP_HAL: enable 32k storage on SITL 2021-01-16 06:47:10 +11:00
Andrew Tridgell f93e2f6717 HAL_ChibiOS: enable 32k FRAM on H7 boards 2021-01-16 06:47:10 +11:00
Andrew Tridgell 9e15efcbb5 AP_InertialSensor: added params restored internal error 2021-01-16 06:47:10 +11:00
Andrew Tridgell 4d58bcb321 AP_Param: support restoring from parameter backup region 
if header on primary parameter storage is corrupt then restore from
backup
 2021-01-16 06:47:10 +11:00
Andrew Tridgell 03a033c5c4 StorageManager: added support for 32k storage with param backup 
when HAL_STORAGE_SIZE == 32768 then add:

 - 1280 more bytes for params
 - double waypoint space
 - add a parameter backup area
 2021-01-16 06:47:10 +11:00
pkocmoud 7b61a4d8c2 HAL_ChibiOS: support F7 with no crystal 2021-01-15 15:48:01 +11:00
Andy Piper 099d6aa72e AP_NavEKF3: add filter reset when vehicle is idle for too long 2021-01-15 15:47:20 +11:00
Andy Piper cb5be4fcc1 AP_HAL_ChibiOS: don't share IMU DMA on MatekH743 to avoid SPI DMA contention 2021-01-15 14:32:39 +11:00
chobitsfan 26a3a02c81 AP_NavEKF3: use posxy_source in all places 2021-01-14 16:49:12 +09:00
李孟晓 40dbb316c1 AP_BattMonitor: ignore SoC option for UAVCAN devices 2021-01-13 18:30:53 +11:00
Andrew Tridgell eeb728237f AP_Compass: removed error on BMM150 
it may be probed at multiple addresses, don't throw lots of errors
 2021-01-13 18:10:25 +11:00
Andy Piper e781572d53 AP_HAL_ChibiOS: support iFlight BeastF7 
reduce DMA contention on BeastH7 and correct sharing
add README's for BeastF7 and BeastH7
 2021-01-13 18:09:33 +11:00
Andy Piper fdbf2d369a AP_HAL_ChibiOS: do not take bi-dir path when in serial DMA 2021-01-13 18:03:41 +11:00
yaapu 89802ed6fc AP_MSP:Tools: use BATTERY_STATE.voltage_cv for cell voltage calculation to replicate actual DJI Goggles behaviour 
This becomes apparent when pack voltage is above DJI's hard limit of 25.5v
with this fix the cell voltage is correct even for 12s packs just like on real hardware
 2021-01-13 17:59:15 +11:00
yaapu b84baf06d3 AP_OpticalFlow: fix MAVLink opflow driver, only apply yaw to flowRate as body rate comes from AHRS 2021-01-13 17:56:27 +11:00
yaapu 5b2d430a2a AP_OpticalFlow: fix CXOF opflow driver, only apply yaw to flowRate as body rate comes from AHRS 2021-01-13 17:56:27 +11:00
Andrew Tridgell 8728148db6 AP_Notify: don't do startup tone on AP_Periph devices 2021-01-13 15:18:40 +11:00
Igor Campos 174700b7ad AP_Mount: Implement roll control on Solo gimbal 2021-01-13 08:39:03 +11:00
Tatsuya Yamaguchi 985642af32 AP_Avoidance: update the description of AVD_F_ALT_MIN to specify MSL 2021-01-12 21:59:44 +09:00
chobits e73d28fe19 AP_NavEKF3: remove redundant extnav code 2021-01-12 21:56:36 +09:00
Josh Henderson 8e705a5eed AP_Logger: move BAT & BCL logging functions to AP_BattMonitor 2021-01-12 17:43:55 +11:00
Josh Henderson e91953fa3b AP_BattMonitor: move log BAT & BCL into AP_BattMonitor 2021-01-12 17:43:55 +11:00
Josh Henderson dfa8e55622 AP_BattMonitor: add has_temperature method to Backend 2021-01-12 17:43:55 +11:00
Peter Barker b92b343d4e SITL: add simulator for ICM40609 2021-01-12 17:43:36 +11:00
Peter Barker 239b09fb34 AP_InertialSensor: add simulator for ICM40609 2021-01-12 17:43:36 +11:00
Peter Barker 3d577d94e8 GCS_MAVLink: add do_disarm_checks boolean to disarm call 
this creates symmetry between arming and disarming, at least as far as
the top-level arm() and disarm() calls are concerned.
 2021-01-12 08:48:44 +09:00
Peter Barker b229c552e6 AP_Arming: add do_disarm_checks boolean to disarm call 
this creates symmetry between arming and disarming, at least as far as
the top-level arm() and disarm() calls are concerned.
 2021-01-12 08:48:44 +09:00
Peter Barker 0052500d67 GCS_MAVLink: split out a handle_command_component_arm_disarm 2021-01-12 08:48:44 +09:00
Brad Bosch a2192eda5e GCS_MAVLink: use RADIO_STATUS message txbuf field 
this avoids overrunning radio buffer in queued_param_send()
 2021-01-12 10:46:15 +11:00
bugobliterator 4346264113 AP_HAL_ChibiOS: ensure UP and CH timer channels share DMA for H7 2021-01-12 10:45:03 +11:00
Peter Barker 96981baadf AP_CanManager: use milliseconds for timeout 
The use of PRIu64 was breaking people's builds
 2021-01-12 10:38:54 +11:00
Peter Barker 9099a9b622 AP_AHRS: correct names for active EKF type 2021-01-12 10:23:08 +11:00
Josh Henderson 0ebbf0f74e AP_Logger: move AP_AHRS functions out 2021-01-12 10:13:22 +11:00
Josh Henderson 62ff9a4d4b AP_AHRS: move logging functions to AHRS 2021-01-12 10:13:22 +11:00
Josh Henderson 8ce5113c74 AC_AutoTune: privatize AHRS logging 2021-01-12 10:13:22 +11:00
Andy Piper e9ea360a99 AP_HAL_ChibiOS: don't timeout after 11 bits on serial irqs 2021-01-12 09:58:58 +11:00
Andrew Tridgell 957842f7eb AP_InertialSensor: added support for v3 Invensense sensors 
starting with ICM-40609, ICM-42688 and ICM-42605
 2021-01-11 14:43:35 +11:00
Andrew Tridgell 14433c3ae3 HAL_ChibiOS: enable ICM-40609 on mRoNexus 2021-01-11 14:43:35 +11:00
yaapu 0f49058fbd AP_MSP: fix for missing ACK on unsupported MSP messages 
MSP requires all messages to be acknowledged even if unsupported
 2021-01-11 08:54:15 +11:00
Andrew Tridgell 882d9c4e23 GCS_MAVLink: adjust stack sizes 2021-01-10 08:28:55 +11:00
Andrew Tridgell dc57454ac5 AP_Logger: adjust stack sizes 2021-01-10 08:28:55 +11:00
Andrew Tridgell afbdd69165 AP_HAL_ChibiOS: adjust stack sizes 2021-01-10 08:28:55 +11:00
Andy Piper 8fb403c569 AP_HAL_ChibiOS: make sure BDMA channels are not adjacent 2021-01-10 08:11:37 +11:00
Andy Piper 186c28c275 AP_BLHeli: correct bi-dir mask enablement 2021-01-09 09:47:40 +11:00
Peter Barker 416dd98140 AP_Logger: check HAL_LOGGING_DATAFLASH only for definition 
As the hwdefs only define the symbol, don't set it to a value...
 2021-01-08 12:48:55 +11:00
Peter Barker 7d42f473fc AP_Logger: allow each backend to be compiled out 2021-01-08 12:48:55 +11:00
yaapu 480c9f10df AP_OpticalFlow: fix for msp opflow sensor alignement 2021-01-08 09:29:23 +09:00
Michael Oborne d2720da4a2 AP_GPS: support yaw for UAVCAN GPS 2021-01-07 15:56:28 +11:00
Michael Oborne 5ef3e1bec3 UAVCAN: add dsdl for gps heading 2021-01-07 15:56:28 +11:00
Peter Barker e8d24a1f68 AP_Logger: initialise logger instance variables in header 2021-01-07 10:42:13 +11:00
Peter Barker 80e8688888 AP_Logger: remove perf counters 2021-01-07 09:20:00 +11:00
Andy Piper b3946a667c AP_Logger: omnibusF4pro needs more stack for logging and logging needs to take precedence over ftp 2021-01-07 07:43:52 +11:00
chobits b0fa5fadcd AP_Logger: fix BCN multiplier 2021-01-06 21:48:32 +11:00
Peter Barker c590aa061f RC_Channel: return uint32_t for number of ms overrides should live 2021-01-06 18:33:15 +11:00
Peter Barker ef0b860a48 AP_Logger: remove Prep and NeedPrep functions 
These were only being called directly after Init(), so just tacked them
onto the end of those functions.

The checks in NeedPrep turned out to be mostly redundant.
 2021-01-06 18:25:21 +11:00
Josh Henderson 1c49a0b44d AP_Logger: only log Battery Status for active monitors 2021-01-06 18:23:15 +11:00
Peter Barker 496267115c AP_RangeFinder: MAVLink: use larger of min ranges / smaller of max ranges 2021-01-06 15:33:41 +11:00
Peter Barker 81ab322daa SITL: correct max_distance in simulated mavlink rangefinder 2021-01-06 15:33:41 +11:00
Peter Barker cba5f142a7 AP_RangeFinder: correct MAVLink backend's out-of-range checks 2021-01-06 15:33:41 +11:00
Peter Barker 223e775a3c AP_RangeFinder_MAVLink: only set sensor type if we accept a reading 2021-01-06 15:33:41 +11:00
Peter Barker 40eb9a8b99 AP_RangeFinder: do not start the mavlink rangefinder as healthy 
Also takes the opportunity to clean things up a little
 2021-01-06 15:33:41 +11:00
Gone4Dirt c96ca2483e AP_Generator: Make sensor unhealthy msg consistent with other sensors 2021-01-06 09:59:34 +11:00
Andrew Tridgell 59fa794818 AP_NavEKF3: constrain vertical error 
this prevents a floating point exception with external AHRS
 2021-01-05 21:13:12 +11:00
Andrew Tridgell 1e75bb971e AP_NavEKF2: constrain vertical error 
this prevents a floating point exception with external AHRS
 2021-01-05 21:13:12 +11:00
Andrew Tridgell ce561ab249 AP_Logger: log active EKF type as ATT.AEKF 2021-01-05 21:13:12 +11:00
Andrew Tridgell b73131cdbc AP_AHRS: review fixes 2021-01-05 21:13:12 +11:00
Andrew Tridgell 4e33b74d69 AP_AHRS: call external AHRS update 2021-01-05 21:13:12 +11:00
Andrew Tridgell b5b9b57c9e AP_AHRS: added external AHRS mavlink status 2021-01-05 21:13:12 +11:00
Andrew Tridgell 75ad1a7d31 AP_AHRS: send a text msg when active EKF changes 2021-01-05 21:13:12 +11:00
Andrew Tridgell 9dbd2d3eba AP_AHRS: expose active EKF type for logging 2021-01-05 21:13:12 +11:00
Andrew Tridgell 7cc71dc573 HAL_SITL: support VectorNav simulation 2021-01-05 21:13:12 +11:00
Andrew Tridgell f57971eafe SITL: added VectorNav simulator 2021-01-05 21:13:12 +11:00
Andrew Tridgell e284c5694d AP_AHRS: added AHRS_EKF_TYPE=11 for external AHRS 2021-01-05 21:13:12 +11:00
Andrew Tridgell b74e5c0e2f AP_InertialSensor: added ExternalAHRS backend 2021-01-05 21:13:12 +11:00
Andrew Tridgell 4f176c25de AP_InertialSensor: relax IMU wait time for low loop rates 
allow for waiting for all IMUs for up to 1/3 of the loop time
 2021-01-05 21:13:12 +11:00
Andrew Tridgell bf51478dd1 AP_GPS: added ExternalAHRS backend 2021-01-05 21:13:12 +11:00
Andrew Tridgell a068e95a48 AP_Compass: added ExternalAHRS driver 2021-01-05 21:13:12 +11:00
Andrew Tridgell 75c789fc57 AP_Baro: added ExternalAHRS backend 2021-01-05 21:13:12 +11:00
Andrew Tridgell 66297bd061 AP_Vehicle: added ExternalAHRS param tree and object 
using EAHRS param prefix
 2021-01-05 21:13:12 +11:00
Andrew Tridgell 0f08236e7c AP_SerialManager: added serial AHRS type 2021-01-05 21:13:12 +11:00
Andrew Tridgell ae4d152d51 AP_SerialManager: added find_portnum() API 
used for allocating device IDs
 2021-01-05 21:13:12 +11:00
Andrew Tridgell 1b60be96d1 AP_ExternalAHRS: added support for external AHRS systems 
First supported is VectorNav VN-300 on serial
 2021-01-05 21:13:12 +11:00
Arsh 3d5addeee0 AP_HAL:examples:AnalogIn: Added comments in the AnalogIn example 2021-01-05 20:43:04 +11:00
Randy Mackay 3a075850f6 AC_Autorotation: minor comment fix 2021-01-05 17:19:43 +09:00
Peter Barker b6833eee9b SITL: correct SMBus block reads 2021-01-05 14:45:20 +11:00
Peter Barker 8be50910e4 SITL: add support for simulated TSYS01 temperature sensor 2021-01-05 12:01:51 +11:00
Peter Barker ecd21fbc4c AP_TemperatureSensor: add support for simulated TSYS01 temperature sensor 2021-01-05 12:01:51 +11:00
murata d7533843d5 AC_AttitudeControl: Set the gravitational acceleration value to the defined value 2021-01-05 09:11:14 +09:00
murata 219dc2e7da AP_InertialSensor: Set the gravitational acceleration value to the defined value 2021-01-05 09:11:14 +09:00
murata 2eee8e389d AP_L1_Control: Set the gravitational acceleration value to the defined value 2021-01-05 09:11:14 +09:00
TsuyoshiKawamura 441be7e04b AP_Scripting: add rangefinder status_orient 2021-01-05 11:03:42 +11:00
Randy Mackay 647c568ab9 AP_NavEKF3: out-of-date comments removed 
GPS, Static and ExtNav yaw buffers have been separated
 2021-01-05 10:58:06 +11:00
Randy Mackay 27c998ad94 AP_NavEKF3: rename source and yawFusionMethod from EXTERNAL to GPS 2021-01-05 10:58:06 +11:00
Randy Mackay 77af6df730 AP_NavEKF: rename EXTERNAL to GPS 2021-01-05 10:58:06 +11:00
Randy Mackay c14b4a8b6c AP_NavEKF3: add support for GSF as yaw source 2021-01-05 10:58:06 +11:00
Randy Mackay 0fb168d6ab AP_NavEKF: source supports GSF yaw 2021-01-05 10:58:06 +11:00
Randy Mackay 5891c6ace8 AP_NavEKF3: separate GPS yaw from ExtNav yaw 2021-01-05 10:58:06 +11:00
Randy Mackay 6850b48ea1 AP_NavEKF3: add comments for yaw sensor variables 2021-01-05 10:58:06 +11:00
Randy Mackay fca8eb0778 AP_NavEKF_Source: add ExtNav yaw source 2021-01-05 10:58:06 +11:00
Peter Hall 1f7d796845 AP_Scripting: add fast param bindings and example 2021-01-05 10:55:36 +11:00
Peter Hall 9dae370356 AP_Scripting: add param accesss helper 2021-01-05 10:55:36 +11:00
Andrew Tridgell 16753a51f4 HAL_Linux: use ExpandingString 2021-01-05 10:52:00 +11:00
Andrew Tridgell 42bc9adfb7 HAL_ChibiOS: use ExpandingString for @SYS buffers 2021-01-05 10:52:00 +11:00
Andrew Tridgell 6da0212ce4 AP_Scheduler: use ExpandingString class 2021-01-05 10:52:00 +11:00
Andrew Tridgell c21b6b4a16 AP_HAL_SITL: use ExpandingString class 2021-01-05 10:52:00 +11:00
Andrew Tridgell 96cbde0ee6 AP_HAL: use ExpandingString class 2021-01-05 10:52:00 +11:00
Andrew Tridgell c924a9917e AP_Filesystem: use ExpandingString class 2021-01-05 10:52:00 +11:00
Andrew Tridgell 0c6b4a1045 AP_CANManager: use ExpandingString class 2021-01-05 10:52:00 +11:00
Andrew Tridgell 6c1891fcb3 AP_Common: added ExpandingString class 
useful for @SYS output construction
 2021-01-05 10:52:00 +11:00
Peter Hall 1a14c8a05b AC_PID: populate pid_info limit feild 2021-01-05 10:27:28 +11:00
Peter Hall b2e1d88da8 AP_Logger: add limit flag to PID logs 2021-01-05 10:27:28 +11:00
Andrew Tridgell 69d3264e55 StorageManager: allow for CANDNA storage on F405 boards 
this allows for boards using the log structure storage with 15360
bytes of storage have a CANDNA area.

This fixes CAN support on F405 boards
 2021-01-05 10:25:17 +11:00
Peter Barker 8f8283e0f0 AP_Motors: rc_map_mask -> motor_mask_to_srv_channel_mask 
the naming of this function precedes our rc/srv-channel split
 2021-01-05 10:19:32 +11:00
Peter Barker d24e569b20 GCS_MAVLink: add option to panic the autopilot 2021-01-05 10:04:25 +11:00
Peter Barker ca6c133042 AP_HAL_ChibiOS: do not reuse va_list after it has been ended 2021-01-05 10:04:25 +11:00
Andrew Tridgell a74d087fd8 SRV_Channel: prevent FPE with SERVOn_MIN==SERVOn_MAX 2021-01-05 08:23:28 +11:00
Josh Henderson 4a7f663cad AP_Logger: README add multiplier descriptions 
Add clarity to the multipliers and descriptions
 2021-01-04 20:45:38 +11:00
Andy Piper 27d7c73c8e AP_RCProtocol: rc_protocols_mask must be set before bootstrap occurs 2021-01-04 20:04:19 +11:00
Josh Henderson ceb2c87970 SITL: align default i2c device bus for BattMonitor 2021-01-04 18:30:09 +11:00
Peter Barker c81df7b5ad AP_Math: add tests for circle-segment-intersection 2021-01-04 13:58:42 +11:00
Peter Barker f534963413 AP_Math: consolidate error checking 2021-01-04 13:58:42 +11:00
murata 4ffc559ccc AP_Math: judge isnan judgment before operation 2021-01-04 13:58:42 +11:00
Peter Barker 8977f3a859 SITL: correct I2C message handling 2021-01-04 12:49:20 +11:00
Peter Barker 23d393e108 SITL: add I2C 8Bit-register methods 2021-01-04 12:49:20 +11:00
Peter Barker 3c16f164df AP_HAL_SITL: correct I2C callback interval 2021-01-04 11:26:12 +11:00
Andrew Tridgell 324ff178d8 HAL_ChibiOS: fixed CUAV_GPS defaults.parm 2021-01-03 16:24:12 -08:00
Tom Pittenger 113f792ad1 AP_HAL_ChibiOS: update periph targets who have buzzer/LEDs with notify 2021-01-03 16:24:12 -08:00
Tom Pittenger 7dde981de6 AP_Notify: add public accessor and param defaults 2021-01-03 16:24:12 -08:00
Andrew Tridgell 6f4bfed82d HAL_ChibiOS: fixed build with alarm and no PWM channels 
this fixes a build error due to conditional always being false when
NUM_GROUPS==0 by using a C++ iterator. It also makes the code neater
 2021-01-04 09:04:06 +11:00
Peter Barker 8e34388a20 SITL: move simulated maxsonari2c to bus 0 
.... where the driver expects it by default
 2021-01-03 20:36:54 +11:00
Peter Barker e5fd661caf SITL: correct I2C multi-bus support 2021-01-03 20:36:54 +11:00
Peter Barker 21ffa4d259 SITL: add sanity check for duplicate bus/addr I2C devices 2021-01-03 20:36:54 +11:00
Peter Barker 995f5d1dad SITL: increase quad scanner range to 18m 
Matches the value we send for Rover, which is useful until we can
reflect on the simulation to discover its maximum range
 2021-01-03 18:54:54 +11:00
Rishabh 2f5f55f680 SITL: Added quadcopter morse example with laser scanner 2021-01-03 18:54:54 +11:00
Peter Barker b1239dcd06 SITL: correct OBSTACLE_DISTANCE message output from SIM_Morse 2021-01-03 17:49:44 +11:00
Andy Piper 40090dcce9 AP_UAVCAN: compile fix for debug/assertions 2021-01-03 08:57:13 +11:00
Andy Piper 176c648156 AP_Terrain: compile fix for gcc 9 2021-01-03 08:57:13 +11:00
Andy Piper 779c2a9e5f AP_Logger: move logger IO to a separate thread 2021-01-02 22:30:08 +11:00
Andrew Tridgell 09603e29ce AP_Compass: fixed external handling for BMM150 2021-01-02 10:31:15 +11:00
Andrew Tridgell 3d4a8829f3 AP_Compass: added BMM150 as available external mag 2021-01-02 10:31:15 +11:00
Andrew Tridgell e747edbcf2 AP_NavEKF3: fixed init order for scheduler 
this can impact replay of EKF2
 2021-01-02 10:30:26 +11:00
Andrew Tridgell b36bfe4206 AP_NavEKF2: fixed init order for scheduler 
this can impact replay of EKF2
 2021-01-02 10:30:26 +11:00
Hwurzburg ce361e51bf HAL_ChibiOS: Reinstate HAL_MINIMIZE_FEATURES for 1MB F7 boards 2021-01-02 08:57:47 +11:00
Andrew Tridgell 6ed4eca57f AP_CANManager: fixed use of CANSensor on multiple ports 
we should not increment _num_drivers if we don't have a driver yet
 2021-01-02 06:25:20 +11:00
Andrew Tridgell 418367c266 HAL_SITL: allow --home to specify a location from locations.txt 
this will make it easy to use a named location in MissionPlanner SITL
 2021-01-01 17:30:32 +11:00
Andrew Tridgell a4517032c5 AP_UAVCAN: log all UAVCAN devices in CAND log message 2021-01-01 17:30:14 +11:00
Andrew Tridgell 0ae9b28198 AP_Logger: added get_log_start_count() 
used by UAVCAN to know if it should log CAN devices on log rotation
 2021-01-01 17:30:14 +11:00
Andrew Tridgell 4fdf315760 AP_Logger: use null terminated strings 
this prevents logging garbage for strings that are shorter than the
length specifier (eg. 'Z'). This assumes we will not want to log
binary data as strings
 2021-01-01 17:30:14 +11:00
Andrew Tridgell 66c05bef76 AP_RangeFinder: added USD1 CAN driver 
also known as uLanding CAN
 2021-01-01 17:29:54 +11:00
Andrew Tridgell 943918d511 AP_Arming: added USD1 CAN 2021-01-01 17:29:54 +11:00
Andrew Tridgell b7fa1a4b98 AP_CANManager: added USD1 CAN driver type 2021-01-01 17:29:54 +11:00
Michael du Breuil 60af6633cf AP_EFI: Add NWPMU CAN driver 2021-01-01 17:29:54 +11:00
Andrew Tridgell fb84baf8a5 AP_Arming: added EFI_NWPMU 2021-01-01 17:29:54 +11:00
Andrew Tridgell db798ace05 AP_CANManager: added EFI_NWPMU 2021-01-01 17:29:54 +11:00
Andrew Tridgell 32c3a2feef AP_CANManager: added CANSensor class 
this makes creation of custom CAN protocol handlers much easier
 2021-01-01 17:29:54 +11:00
Andrew Tridgell e260c7ad59 HAL_ChibiOS: update f303-MatekGPS to allow disable of MSP 
and use DMA for MSP
 2021-01-01 15:40:13 +11:00
David B. Bitton 8dbe0a71ba AP_HAL_ChibiOS: add support for Toshiba LED 2020-12-31 11:02:10 -08:00
Tom Pittenger 8e6278f269 AP_ADSB: add Sagetech XP driver 2020-12-30 17:56:38 -08:00
Tom Pittenger ffd3d1da1d AP_SerialManager: add support for ADSB protocol 2020-12-30 17:56:38 -08:00