Jason Short
1a6549fef7
removed GPS ground speed calc - was causing some funny business during the transition.
2012-07-03 17:16:14 -07:00
Jason Short
c62706ad06
Toy Mode: Yaw performance update.
2012-07-03 17:14:54 -07:00
Jason Short
8a08a74cc6
Config.h : shortening the landing time to 10s
2012-07-02 17:52:38 -07:00
Jason Short
16b25a26c2
Toy Mode: removed virtual WP, copter now just goes into auto_loiter when not holding the sticks.
2012-07-02 17:52:38 -07:00
Andrew Tridgell
060cbe2030
AP_Mount: removed unused enum
2012-07-03 10:39:34 +10:00
Andrew Tridgell
99b11e4f19
Mount: enable mount control via eeprom parameters
...
this enables MNT_* parameter control of the camera mount code. It also
fixes the conversion of calculated angles between degrees and
integers, and fixes stabilised mount control when yaw control is not
available.
2012-07-03 10:21:01 +10:00
Andrew Tridgell
82e09ce53a
SITL: don't enable wind until we are off the ground
...
this makes it possible to test with much larger wind speeds, without
the sim crashing due to the wind flipping us over on the runway
2012-07-03 10:19:20 +10:00
Andrew Tridgell
057eb5e6f6
Baro: average over all pressure/temperature samples on MS5611
...
this allows us to use the MS5611 barometer at its full 100Hz sample
rate (80Hz for pressure, 20Hz for temperature). The pressure and
temperature values are averaged between reads without adding any
latency. Previously the driver would throw away values between
readings
This also fixes a race condition in reading from the SPI bus that
could lead to bad values from the barometer
2012-07-02 13:44:53 +10:00
Andrew Tridgell
f70cd71791
Baro: fixed build of MS5611 test code
2012-07-02 13:44:53 +10:00
Jason Short
e0b3309500
Yaw mode:
...
Improved hybrid Yaw mode:
- uses rate controller rather than as fast as possible
- waits 1.5 seconds before entering hold
- bounce free
2012-07-01 13:40:12 -07:00
Jason Short
9a30270879
System.pde - RTL
...
removed Approach mode, fixed RTL to loiter until desired altitude is reached
2012-07-01 13:40:12 -07:00
Jason Short
e35fb9ecd7
Parameters
...
removed unused parameters for retro loiter
2012-07-01 13:40:12 -07:00
Jason Short
3cf16c1424
GCS_Mavlink.pde
...
removed Approach define
2012-07-01 13:40:11 -07:00
Jason Short
ab564b8a86
defines.h
...
removed Approach mode enumeration
2012-07-01 13:40:11 -07:00
Jason Short
3646d69faf
read_control_switch
...
Removed Prev_WP reference. unneeded.
2012-07-01 13:40:11 -07:00
Jason Short
8ab1acfb92
Config.h
...
Removed Approach delay redundancy - using land timer instead
Removed Retro loiter mode param
2012-07-01 13:40:11 -07:00
Jason Short
2ad08fdd98
RTL: Commands.pde
...
When we are out of commands we land or Loiter at the RTL_Approach_altitude.
2012-07-01 13:40:11 -07:00
Jason Short
d58ceb2b09
RTL: Commands.pde
...
Removed do_approach function - now redundant
2012-07-01 13:40:11 -07:00
Jason Short
c5617eeeac
Arducopter.pde_RTL:
...
added a new RTL function that goes into Loiter, first, checks if we have reached RTL_Altitude, then enters WP mode to come home.
Removes Approach mode. Uses Auto_Approach value to decide if we should land or descend to a certain altitude
2012-07-01 13:40:11 -07:00
Jason Short
2450c25544
Arducopter: enabled RTL_altitude, renamed function to be more accurate
2012-07-01 13:40:11 -07:00
Jason Short
2e8eee9306
Added code for self centering throttle - disabled by default.
2012-07-01 13:40:11 -07:00
Michael Oborne
b2d73d8f68
fixup sitl attribute group for planner. - causing invalid advanced/standard views
2012-07-01 21:43:32 +08:00
Michael Oborne
46f004bcca
APM Planner 1.1.95
...
fix config panel value change detection
add loiter_ to AC config screen
Add praram name to Friendly param, and exception ignoring.
fix param file note line
intergrate andrews gimbal config.
fix any possible log appending issues
remove old cli planner on connect
modify speech to not crash on windows mono
2012-07-01 17:51:22 +08:00
Andrew Tridgell
d1cb8c9a60
ArduBoat: removed use of analogRead()
2012-07-01 15:09:39 +10:00
Andrew Tridgell
769011e947
AnalogSource: added some example code
2012-07-01 15:01:05 +10:00
Andrew Tridgell
1fdcc3e8f0
SITL: added support for new analog source
...
removed analogRead() to prevent people using it
2012-07-01 15:01:05 +10:00
Andrew Tridgell
82ede937e7
AnalogSource: convert analogRead() calls to the new API
...
this should give us much better analog values, plus save a bunch of
CPU time
2012-07-01 15:01:05 +10:00
Andrew Tridgell
c8befe4536
AnalogSource: make the Arduino AnalogSource interrupt driven
...
this fixes several problems with reading analog sources:
- we were getting poor values because we didn't wait long enough for
an analog source to settle
- we wasted a lot of CPU cycles waiting for conversions
- we were not taking averages over many samples, which we did with
the old AP_ADC driver on the APM1
2012-07-01 15:01:05 +10:00
rmackay9
78fa903e17
ArduCopter: updated STABILIZE_ROLL_I to 0.01 (was 0.1) as instructed by Marco
2012-06-30 19:26:14 +09:00
Jason Short
4d6ccccef5
Circle_WP distance check fix
2012-06-29 21:20:28 -07:00
Jason Short
59d16f5fe0
Commands.pde: increased bad WP distance check
2012-06-29 21:20:28 -07:00
Jason Short
eea788b63f
navigation.pde : Added a drag/velocity prediction filter for improved I term wind correction.
2012-06-29 21:20:28 -07:00
Jason Short
031830b5fe
System.pde: Toy mode details for set_mode()
2012-06-29 21:20:28 -07:00
Jason Short
c276fe8fa0
GCS_Mavlink: added notes to #if malink10
2012-06-29 21:20:28 -07:00
Jason Short
0011190880
defines.h: Toy Mode defines for flight modes
2012-06-29 21:20:28 -07:00
Jason Short
4450d80ea3
Config.h: Optimizing Nav gains
2012-06-29 21:20:28 -07:00
Jason Short
3ce867508b
Attitude.pde: Toy mode logic
2012-06-29 21:20:27 -07:00
Jason Short
668135ea8b
Arducopter.pde: Added Toy mode refinements
2012-06-29 21:20:27 -07:00
Jason Short
49401bffae
Params: Added toy_yate_rate
2012-06-29 21:20:27 -07:00
Jason Short
5e4d28baf0
Added Toy mode to navigation
2012-06-29 21:20:27 -07:00
Jason Short
e036bee424
Aeducopter.pde: Toy mode updates
2012-06-29 21:20:27 -07:00
Adam M Rivera
61baa666c4
commands_process.pde: Bug fix 427. By default, the copter would land after an AUTO mission. Updated to check for valid approach altitude at end of mission.
2012-06-29 21:41:56 -05:00
Andrew Tridgell
136c03c3c0
AHRS: include the P terms in get_gyro()
...
this makes it more useful for navigation controllers
2012-06-29 21:54:09 +10:00
Andrew Tridgell
acc6adf6e9
MPU6k: removed an unused variable
2012-06-29 21:54:09 +10:00
Andrew Tridgell
55092c25a6
SITL: enable the SIM_* parameters in ArduCopter and ArduPlane
2012-06-29 15:10:52 +10:00
Andrew Tridgell
ed691fc465
SITL: added SITL class for controlling simulation
...
this holds mavlink settable parameters for controlling sensor noise
levels
2012-06-29 15:10:51 +10:00
Andrew Tridgell
16c55c64d4
AHRS: don't add the P terms in _omega
...
this can lead feedback via the _P_gain()
2012-06-29 15:10:51 +10:00
Adam M Rivera
dadc7d5a7d
ArduCopter: Loiter Timer should have been set when the approach altitude was set. Previously, land had to be enabled before auto approach would work.
2012-06-28 20:34:53 -05:00
Andrew Tridgell
37fc6c46b9
AHRS: disable barometer for vertical acceleration
...
this seems to have been the cause of the 'flips' seen by Marco and
others. Testing by Craig and Alan shows that the flips are gone when
the barometric acceleration is removed.
It looks like a 5 point average filter is not enough to keep the
vertical acceleteration noise low. With high noise in the z axes, the
x and y axes are scaled back when the ge vector is normalised.
2012-06-28 11:12:49 +10:00
Andrew Tridgell
58c4d458dc
AHRS: re-instate new DCM drift correction code
...
This reverts commit 078489638d47fbaffde7c51249e36b5a8fc4ef9d.
2012-06-28 11:09:22 +10:00