When registering accel and gyro we use the upper 16bits of the id to
store the driver version. When changing the driver behavior in
non-compatible ways, changing this version will trigger a request for
calibration.
This allows each sensor to be uniquely identified in the system by using
either the index inside the backend or for those that use the Device
interface, to use the bus type, location, and device id.
We leave 16-bit for each sensor to be able to change its own
identification in future, which allows them to be changed in an
incompatible manner forcing a re-calibration.
We only leave the parameter there for backward-compatibility. However
product id on the inertial sensor is not much useful since it's only
kept for the first instance.
A better implementation per-gyro and per-accel is needed in order to
avoid problems with sensors taking the offsets configured for another
sensor.
We should return the number of bytes written/read, not 0 on success.
This number may be useful in some cases so return it.
While at it fix a simple wrong space in the header.
Data-ready pin wasn't being used before due to a bug in the Kernel with
concurrent accesses to GPIO in Intel Baytrail platforms. That has been fixed in
Kernel version 4.2.
The PSTR is already define as a NOP for all supported platforms. It's
only needed for AVR so here we remove all the uses throughout the
codebase.
This was automated with a simple python script so it also converts
places which spans to multiple lines, removing the matching parentheses.
AVR-specific places were not changed.
In order to avoid confusion between sample rate from sensor and sample rate
from the frontend class (AP_InertialSensor), use "raw sample rate" to refer to
the former.
The changes in the code were basically done with the following commands:
git grep -wl _accel_sample_rates | xargs sed -i "s,\<_accel_sample_rates\>,_accel_raw_sample_rates,g"
git grep -wl _set_accel_sample_rate | xargs sed -i "s,\<_set_accel_sample_rate\>,_set_accel_raw_sample_rate,g"
git grep -wl _accel_sample_rate | xargs sed -i "s,\<_accel_sample_rate\>,_accel_raw_sample_rate,g"
git grep -wl _gyro_sample_rates | xargs sed -i "s,\<_gyro_sample_rates\>,_gyro_raw_sample_rates,g"
git grep -wl _set_gyro_sample_rate | xargs sed -i "s,\<_set_gyro_sample_rate\>,_set_gyro_raw_sample_rate,g"
git grep -wl _gyro_sample_rate | xargs sed -i "s,\<_gyro_sample_rate\>,_gyro_raw_sample_rate,g"
And also with minor changes on indentation and comments.
The code with ifdef for !FAST_SAMPLING is bit rotting and the example
for AP_InertialSensor is currently broken for this case. Instead of
adding more ifdefs, remove the legacy implementation for !FAST_SAMPLING
since we don't support it anymore.
Reported by Grant:
/home/grant/3dr/ardupilot/libraries/AP_InertialSensor/AP_InertialSensor_MPU6000.cpp:
In member function 'void AP_InertialSensor_MPU6000::_accumulate(uint8_t*,
uint8_t)':
/home/grant/3dr/ardupilot/libraries/AP_InertialSensor/AP_InertialSensor_MPU6000.cpp:776:20:
error: no match for 'operator+=' (operand types are 'Vector3l {aka
Vector3<long int>}' and 'Vector3f {aka Vector3<float>}')
_accel_sum += accel;
/home/grant/3dr/ardupilot/libraries/AP_InertialSensor/AP_InertialSensor_MPU6000.cpp:777:19:
error: no match for 'operator+=' (operand types are 'Vector3l {aka
Vector3<long int>}' and 'Vector3f {aka Vector3<float>}')
_gyro_sum += gyro;
Read temperature as part of the normal burst. This is not very costly since it
is part of the burst read in i2c and already read in spi.
It is meant to be used for imu heating.
The filter is set to 1Hz on temperature because of the inherent inertia of
heating systems.
In 294298e ("AP_InertialSensor: use method for downcast") I was too eager
to use "auto" and ended up using the implicit copy constructor instead
of actually getting a reference to the object.
