This warning happens because of the difference of datatypes between
32 and 64 bits processors.
%% libraries/AP_HAL_Linux/RCInput_UDP.o
/home/zehortigoza/dev/ardupilot/libraries/AP_HAL_Linux/RCInput_UDP.cpp: In member function 'virtual void Linux::LinuxRCInput_UDP::_timer_tick()':
/home/zehortigoza/dev/ardupilot/libraries/AP_HAL_Linux/RCInput_UDP.cpp:42:72: warning: format '%llu' expects argument of type 'long long unsigned int', but argument 3 has type 'uint64_t {aka long unsigned int}' [-Wformat=]
hal.console->printf("no rc cmds received for %llu\n", delay);
As AVR2560 is not supported anymore and do integer operations is
usually faster than float-point the _calculate() implementation was
done using only integer operations and as more close to what
datasheet says.
offset parameter units are milligauss
User settable parameters should have a User category defined. Those that should never be set by a user should not have this.
The function rotate_field() can change the values axes and the function
correct_field() applies offsets (which are already in milligauss). Thus any
sensitivity adjustment must be done for two reasons:
(1) The offsets must be applied to the values already in milligauss;
(2) The factory sensitivity adjustment values are per axis, if any rotation
that switches axes is applied, that'll mess with the adjustment.
Experiments showed that before this patch the length of the mag field reported
quite different from the expected. After this patch, the same experiments
showed reasonable values.
This is part of the transition to make all mag field values be used in
milligauss. Additionally the value of _gain_multiple is adapted to the new way
we're using it and corrected accordingly to the datasheets.
The use of _gain_multiple is not necessary because the values of
expected_{x,yz} and _mag_{x,y,z} are both in sensor raw unit (i.e., lsbs).
That wasn't fixed before in order not to make APM users to recalibrate their
compasses.
The failure to initialise the magnetometer bias states to zero can result in a large jump in yaw gyro bias and heading when a heading reset is performed.
Fixes a potential error where changes to timing and arrival rate of magnetometer and baro data could block the fusion of synthetic position and velocity measurements, allowing unrestrained tilt errors during operation without GPS or optical flow.
Fusion of synthetic position or velocity measurements is now timed to coincide with fusion of barometer observations.
If a new barometer observation has not arrived after 200 msec then the synthetic position or velocity is fused anyway so that fusion of synthetic position or velocity observations cannot occur any slower than 5 Hz
Previous check default only checked the number of satellites and horizontal position accuracy.
Updated default value also checks HDoP and speed accuracy.
Fixes the issue of three unused variables, two of which were used in a
commented Debug() call.
To keep the convenient debug message (and the variable names for the
data bytes), this patch uncomment the debug call but wrap the variables
and the debug call around an ifdef for the local symbol
gsof_DEBUGGING. So by turning it on, the debug will already be in place.
The Debug() call was modified to actually compile and include the third
variable in the output.
It uses a heating resistor controlled by a pwm.
By changing the duty cycle of the pwm, we can control the temperature.
A simple PI algorithm is used in order to get to the correct temperature
fast enough and without too much overshoot
It is implemented as a member of the Util class in order not to make to much
modification to the current codebase
Read temperature as part of the normal burst. This is not very costly since it
is part of the burst read in i2c and already read in spi.
It is meant to be used for imu heating.
The filter is set to 1Hz on temperature because of the inherent inertia of
heating systems.
Surround calls to rcout->write() with rcout->cork() and rcout->push().
If the RCOutput implementation allows the writes are grouped and only
sent together to the underlying hardware.
Fix warning and use htole16 instead of trying to implement it.
The current code does nothing on little endian platforms.
Moreover, the status variable was unused.
MPU6000 data sheet indicates that variation on gyro ZRO across temperature range from -40 to +85 is +-20 deg/sec.
The limits on the gyro bias states have been increased to allow for this.
To enable the EKF to accommodate such large gyro bias values in yaw without the yaw error wrapping, leading to continual heading drift, an unwrap function has been applied to the compass heading error.
