Randy Mackay
0812e16008
Copter: explicitly define flight modes enum
...
Thanks to Luis Vale for spotting this
2015-05-02 13:24:33 +09:00
Robert Lefebvre
41a6cc64ff
Copter: Log Emergency Stop and Motor Interlock status
2015-05-01 14:30:43 +09:00
Robert Lefebvre
d8a0952b5a
Copter: Explicitly define aux_switch enum.
2015-05-01 14:30:42 +09:00
Robert Lefebvre
da2854403e
Copter: Explicitly define tuning_func enum value
2015-05-01 14:30:42 +09:00
Robert Lefebvre
fab8604f16
Copter: Change Auto Yaw #define table into Enum.
2015-05-01 14:30:39 +09:00
Robert Lefebvre
32b4e70cb7
Copter: Deprecate Aux Switch Multi-Mode
2015-05-01 14:30:38 +09:00
Robert Lefebvre
22a7fba289
Copter: Change autopilot modes into Enum
2015-05-01 14:30:37 +09:00
Robert Lefebvre
39d23519b1
Copter: Change CH6_Tuning #defines into Enum
2015-05-01 14:30:36 +09:00
Robert Lefebvre
2010410c44
Copter: Add numbers to Aux Switch Enum comments
2015-05-01 14:30:28 +09:00
Robert Lefebvre
7349827eb1
Copter: Add Aux Switch E-Stop Function
2015-05-01 14:30:26 +09:00
Robert Lefebvre
e4c5915330
Copter: initial creation of motor_interlock
2015-05-01 14:30:21 +09:00
Jonathan Challinger
73d961cebc
Copter: mavlink initiated takeoff in alt-hold modes
...
adds PILOT_TKOFF_ALT for target altitude above home in cm for pilot initiated takeoff
2015-05-01 12:56:18 +09:00
Andrew Chapman
4311cd4e7a
Copter: add logging for CH6 parameter tuning
...
Logs CH6 tuning values to a new PTUN log struct, specific to
APM::Copter at this point
2015-04-28 14:14:01 +09:00
Andrew Tridgell
cb2427ef9e
Copter: removed special cases for DCM gain changes on arm/disarm
...
copter no longer uses DCM, so it doesn't need these special cases
2015-04-28 14:07:39 +10:00
Robert Lefebvre
1aa696bc10
Copter: Implement Stop Mode
2015-04-26 16:11:47 +09:00
Randy Mackay
dfb720bab6
Copter: rename FULL_IMU logging to IMU_FAST
...
This naming is consistent with the earlier ATTITUDE_FAST option and
clarifies that it's the rate that's increased rather than the content.
2015-04-20 13:49:04 +09:00
Peter Barker
5a45de5e00
Copter: IMU full-rate logging LOG_BITMASK flag
2015-04-20 13:48:58 +09:00
Jaime Machuca
3c00b0a0a8
Copter: ch7/ch8 for lost copter sound
2015-04-13 17:44:39 +09:00
Randy Mackay
11576a0f1e
Copter: fix bitmask for use with SET_POSITION_TARGET
...
Thanks to vooon for spotting this
2015-04-11 11:57:41 +09:00
Randy Mackay
74b98b89d0
Copter: remove dcm check
2015-03-27 00:04:37 -07:00
Randy Mackay
522ef8f91f
Copter: rename MOT df msg to MOTB
...
This will slightly reduce confusion with the MOT message from AC3.1.5
that eventually became RCOUT
2015-03-18 21:25:45 +09:00
Randy Mackay
b679fd0be0
Copter: log RATE with ATT
2015-03-18 21:25:42 +09:00
Randy Mackay
e6c3f4f97b
Copter: move aux switch enum to defines.h
2015-03-17 21:18:49 +09:00
Robert Lefebvre
97cd3614eb
Copter: Change Aux Switch function list to enum.
2015-03-17 21:18:46 +09:00
Robert Lefebvre
a5af151a91
Copter: Initial expansion of Aux Switch to Ch7-12
2015-03-17 21:18:41 +09:00
Randy Mackay
fbfc94cf69
Copter: remove GPS glitch and failsafe
...
The EKF failsafe now captures all failures that could lead to a bad
position including GPS glitches and a bad compass meaning we do not need
this protection in the main flight code.
2015-03-13 16:40:46 +09:00
Randy Mackay
0476558049
Copter: remove USE_EKF from ch7/ch8 switch
2015-03-13 16:40:20 +09:00
Leonard Hall
c78480e14f
Copter: rename loiter_pos to pos_xy
...
Also renamed throttle_rate to vel_z, throttle_accel to accel_z
2015-03-06 14:02:17 +09:00
Leonard Hall
e232867661
Copter: move LOITER_RATE to 2-axis PI controller
...
Also rename LOITER_RATE to VEL_XY for parameters, definitions, variables
2015-03-06 14:02:15 +09:00
Leonard Hall
1ec5eedd23
Copter: ch6 tuning of yaw rate filter
2015-03-06 14:02:13 +09:00
Leonard Hall
8ba195a3a2
Copter: add Mot and Rate dataflash logging
2015-03-06 14:02:07 +09:00
Leonard Hall
3e8563dd8b
Copter: ch6 tuning definition for yaw min headroom
2015-03-03 15:48:17 +09:00
Andrew Tridgell
74ef1b8d2f
Copter: removed HomeState from defines.h
...
now in AP_Common.h
2015-02-21 10:14:32 +11:00
Randy Mackay
e081b9d1c7
Copter: home is set becomes three state
2015-02-12 15:00:50 +09:00
Randy Mackay
34503de18e
Copter: integrate SerialManager
...
Remove serial0, serial1 baud and protocol parameters
Pass serial_manager to GCS, GPS, mount, FrSky_telem objects during init
call SerialManager init_console on startup
use SerialManager's set_block_writes_all
2015-01-29 14:05:14 +11:00
Robert Lefebvre
4b86a4aeec
Arducopter: Change mode logging to use common-vehicle DataFlash library.
2015-01-21 14:37:20 +09:00
Robert Lefebvre
422970a1b1
Arducopter: Change compass logging to use common-vehicle DataFlash library.
2015-01-21 14:37:16 +09:00
Robert Lefebvre
1b152cf2bf
ArduCopter: Change Current logging to use common-vehicle logging in DataFlash library.
2015-01-21 14:37:04 +09:00
Robert Lefebvre
c9d5b6aa7f
Arducopter: Change Attitude logging to use common-vehicle logging in DataFlash library.
2015-01-21 14:36:59 +09:00
Randy Mackay
80f59694d0
Copter: remove deprecated Guided-Spline
...
Guided-Spline has been replaced by Guided-PosVel
2015-01-07 14:03:50 +09:00
Jonathan Challinger
bc29008233
Copter: add guided_posvel
2015-01-07 14:02:21 +09:00
Robert Lefebvre
e10e020062
Copter: Add Landing Gear functionality to main code
2015-01-07 11:58:16 +09:00
Randy Mackay
67fdfffc2a
Copter: remove OF_Loiter PIDs and tuning
2014-12-08 14:58:18 +09:00
Jonathan Challinger
387f3276cb
Copter: handle SET_POSITION_TARGET mavlink messages
2014-11-17 14:38:55 -08:00
Jonathan Challinger
1b1327dc93
Copter: add Guided_Spline mode
2014-11-17 14:38:48 -08:00
Jonathan Challinger
80ba40d149
Copter: CPU failsafe logs an error
2014-11-08 11:27:16 +09:00
Jonathan Challinger
d7d8330303
Copter: loiter copter without accepting user input at end of auto mission
2014-10-20 10:46:14 +09:00
Andrew Tridgell
c3d839456b
Copter: support logging while disarmed
2014-10-17 16:29:59 +09:00
Randy Mackay
b9977a1115
Copter: add land_complete_maybe flag
2014-09-19 16:43:15 +09:00
Randy Mackay
3fa3cb6d65
Copter: remove EPM neutral from ch7/ch8 switch
...
The EPM library returns the pwm output sent to the EPM to the neutral
position automatically meaning an explicit ch7/ch8 setting is not
required
2014-09-17 21:13:45 +09:00
