* Retains ability to read from Analog Pin
* Adds ability to read RSSI from PWM channel value as is done in OpenLRSng, EazyUHF, and various other LRS.
* Handles any type of RSSI that provides RSSI values inverted - i.e. when the low value is the best signal and the high value is the worst signal.
* Has different key names from all existing RSSI parameters to provide for a clean break and easier distinguishing.
Like was done to inertial AK8963 and inertial sensor move the decision
regarding the I2C bus to the caller. We don't allow changing the address
because apparently HMC5843 doesn't support different addresses.
Changing only the bus could be more easily done but this prepares the
ground for using HMC5843 on an AuxiliarBus.
The need for a more generic abstraction is evidenced by this commit: a
"SerialBus" in AP_HAL would be a nice addition rather than letting each
driver to provide its own. However the methods are a little bit
different from what we have in AK8963. It's safer to do the simple
conversion now and later on to add the abstraction changing everybody to
use it.
read() calls accumulate() which takes the lock by itself so we must
release it like we were doing before 669ae26 ("AP_Compass: encapsulated
calibration in HMC").
Just like was done for inertial sensor, different detect() functions
might need different arguments and passing a pointer to function here is
cumbersome. For example, it forces to have a method like "detect_i2c2"
rather than allowing hal.i2c2 to be passed as parameter.
In order to allow other libraries to use the InertialSensor we need a
way to let them to get the only instance of InertialSensor. The
conventional way to do a singleton would be to let the constructor
private and force it to be instantiated from the get_instance() method.
Here however we just call panic() on the constructor if there's already
an instance alive. This allows us to let the vehicles as is. Later we
can change it so they call the get_instance() method instead.
Add an AuxiliaryBus class that can be derived for specific
implementations in inertial sensor backends. It's an abstract
implementation so other libraries can use the auxiliary bus exported. In
order for this to succeed the backend implementation must split the
initialization of the sensor from the actual sample collecting, like is
done in MPU6000.
When AP_InertialSensor::get_auxiliary_bus() is called it will execute
following steps:
a) Force the backends to be detected if it's the first time it's
being called
b) Find the backend identified by the id
c) call get_auxiliary_bus() on the backend so other libraries can
that AuxiliaryBus to initialize a slave device
Slave devices can be used by calling AuxiliaryBus::request_next_slave()
and are owned by the caller until AuxiliaryBus::register_periodic_read()
is called. From that time on the AuxiliaryBus object takes its ownership.
This way it's possible to do the necessary cleanup later without
introducing refcounts, that we don't have support to.
Between these 2 functions the caller can configure the slave device by
doing its specific initializations by calling the passthrough_*
functions. After the initial configuration and register_periodic_read()
is called only read() can be called.
Identify backend with an id, allowing other libraries to connect to
them. This is different from the _product_id member because it
identifies the sensor, not the board the sensor is in, which is
meaningless for our use case.
This allows backends to have a separate detection and initialization
logic. It doesn't change any backend yet and with the current code
there's no change in behavior either. This only allows
AP_InertialSensor::_detect_backend() to be called earlier so
AP_InertialSensor object can be used by other libraries. If it's not
called, later on AP_InertialSensor::init() will detect and start all
backends.
We were able to read only the block of registers that are part of the
data output from accelerometer/gyroscope. In order to support reading
the external sensors we need support for reading a generic block of
registers.
Now that we have a pre-arm check in place to detect bad lidar, the motion check is unnecessary and can false trigger for copters with flexible undercarriages or on uneven ground.
This param seems to have been un-implemented. This is putting it back in. Adds a meter offset to the calculated altitude form the baro sensors.
Also changes it from int8 to float
There are implementations for float, Vector2f and Vector3f for the Low
Pass Filter and the *2p filter. I tried to implement these filters
with one common template implementation. This implementation saves
some lines of code and reduced the redundancy. One could save even
more code if the currently overloaded isinf/isnan functions and checks
can be removed.
Signed-off-by: Daniel Frenzel <dgdanielf@gmail.com>
very strict check that all axis are not vibrating much at all
new param: INS_STILL_THRESH used to be a vibration threshold for different platforms
// @Description: Threshold to tolerate vibration to determine if vehicle is motionless. This depends on the frame type and if there is a constant vibration due to motors before launch or after landing. Total motionless is about 0.05. Suggested values: Planes/rover use 0.1, multirotors use 1, tradHeli uses 5
Param 1 denotes which direction the user expects the plane to
travel when changing altitude:
0 = no expectation, command completes when within 5 m of altitude.
1 = climb expected, command completes at or above altitude.
2 = descent expected, command completes at or below altitude.
This method checks for consistency between accelerometer readings and switches to the unit with the lowest vibration of the difference exceeds 0.3g
The threshold of 1.7 m/s/s corresponds to a maximum tilt error of 10 deg assuming one IMU is good, one is bad and the EKF is using the bad IMU.
Now instead of requiring the buffer to fill completely before we can
detect it is not draining, we use a time based mechanism to detect
when none of the first few bytes are transmitted after sitting in our
buffer a half second or more after flow control is enabled. This
huristic is reliable only for the first several chracters because we
believe that the radio must still have plenty of room in it's own
buffers at that time even if it is not able to transmit them to the
other radio yet. Note that the original algorithm made the same
assumption.
The new algorithm is especially helpful for cases where only keepalive
messages are transmitted before other packets can be requested by the
GCS. In this situation, the original code required almost 2 minutes
to disable flow control and allow communication with the GCS.
It was not only standardized, but actually fixed since ".." would not
move to the libraries/ directory (and hence the include location was
actually wrong).
Fredrik Hedberg
Andrew Tridgell
Tom Pittenger
Stewart Loving-Gibbard
Grant Morphett
Lucas De Marchi
Staroselskii Georgii
squilter
Paul Riseborough
Randy Mackay
fillycheezstake
Leonard Hall
ziltoid2
dgrat
Michael Day
Brad Bosch