Randy Mackay
3a49797e1e
Copter: version to 3.5.4-rc1
2017-11-08 11:01:25 +09:00
Randy Mackay
c9558124cf
Copter: 3.5.4-rc1 release notes
2017-11-08 11:01:24 +09:00
bnsgeyer
63f2a0eaf2
AP_Motors: Tradheli- fixes servo_test function for Dual Heli frame
2017-11-08 11:01:23 +09:00
Andrew Tridgell
45e71fc2e7
AP_Motors: fixed scaling of servo outputs
...
thanks to bnsgeyer for noicing this in issue #6977
this will break existing dual-heli setups, but there are so few people
flying them so far that I think it is a worthwhile change
2017-11-08 10:11:30 +09:00
Peter Barker
8717f1f27e
DataFlash: protect write fd with semaphore
...
If the sensor threads are using WriteBlock they may pass the _write_fd
== -1 check but then have that set to -1 by the main thread
This is a backport of 3af5be76aa
2017-11-07 16:16:22 +09:00
Francisco Ferreira
594edc1929
AP_Rangefinder: search buses 0 and 1 for Maxbotix I2C driver
2017-11-07 13:57:35 +09:00
Francisco Ferreira
edd8fb5293
AP_HAL: stop defining a default Lightware I2C bus
...
When a specific bus isn't defined we now search I2C buses 0 and 1
2017-11-07 13:57:35 +09:00
Francisco Ferreira
633b17f7e5
AP_Rangefinder: look in buses 0/1 when Lightware I2C bus isn't defined
2017-11-07 13:57:35 +09:00
ChristopherOlson
3296bcb10a
AP_Motors:TradHeli - DDFP Tail
...
change to prevent DDFP Tail from starting without motor interlock raised and armed state = true
Change Type: bug fix - resolves issue #6287
2017-11-07 13:52:45 +09:00
ChristopherOlson
979a52469f
Copter:TradHeli - Default ACCEL_Z_P
...
change default ACCEL_Z_P to 0.3 for traditional helicopters to prevent collective pitch oscillation in altitude controlled flight modes
Change Type: enhancement - partially resolves issue #2974
merged with Copter master #7127
2017-11-07 13:41:14 +09:00
Andrew Tridgell
5c94463667
PX4NuttX: submodule update
...
fixed flash write for stm32 errata
2017-11-07 13:38:29 +09:00
Lucas De Marchi
209a2463a0
PX4Firmware: update submodule with fixes to upload script
2017-11-07 13:37:57 +09:00
Andrew Tridgell
1c9d34b96e
AP_SerialManager: enable debug console use for other protocols
...
this allows SERIAL5_PROTOCOL to be set on FMUv2 and FMUv3 for use by
other protocols
2017-11-07 11:57:40 +09:00
Andrew Tridgell
1f7a06ebd5
HAL_PX4: allow uart5 to be used for non-nsh on FMUv2/FMUv3
2017-11-07 11:57:39 +09:00
Kevin Lopez Alvarez
86d3de31a1
HAL_PX4: Adjust SPI params for ppro
...
Add SPI prescalers for 180 MHz and decrease LIS3MDL SPI speed
2017-11-07 11:57:38 +09:00
Kevin Lopez Alvarez
580295900f
AP_Compass: LIS3MDL correct orientation
2017-11-07 11:57:37 +09:00
Kevin Lopez Alvarez
6c93749558
travis: Add ppro target
2017-11-07 11:57:37 +09:00
Kevin Lopez Alvarez
aa61a6231b
AP_Compass: Remove comments and use correct board number
2017-11-07 11:57:36 +09:00
Kevin Lopez Alvarez
cf4e805470
AP_BoardConfig: Remove comments and use correct board number
2017-11-07 11:57:35 +09:00
Kevin Lopez Alvarez
5db5c752fe
mk: Add bootloader for FMUv4pro
2017-11-07 11:57:34 +09:00
Kevin Lopez Alvarez
eb9c3ee972
AP_InertialSensor: add ppro support
2017-11-07 11:57:34 +09:00
Kevin Lopez Alvarez
2f1553d5e2
HAL_PX4: add ppro support
2017-11-07 11:57:33 +09:00
Kevin Lopez Alvarez
80d4a87975
AP_Compass: add ppro support
...
disable lis3mdl for now
2017-11-07 11:57:32 +09:00
Kevin Lopez Alvarez
26973fec54
waf: Initial waf support for ppro
2017-11-07 11:57:30 +09:00
Kevin Lopez Alvarez
1ce9917fd0
Tools: initial FMUv4pro support
2017-11-07 11:57:24 +09:00
Kevin Lopez Alvarez
6943e33c09
mk: initial FMUv4pro support
2017-11-07 11:21:17 +09:00
Kevin Lopez Alvarez
dea4b78387
AP_HAL_PX4: initial FMUv4pro support
2017-11-07 11:13:37 +09:00
Kevin Lopez Alvarez
905b34f84b
AP_HAL: initial FMUv4pro support
2017-11-07 11:13:33 +09:00
Kevin Lopez Alvarez
5dcb9544ae
AP_BoardConfig: initial FMUv4pro support
2017-11-07 11:13:30 +09:00
Kevin Lopez Alvarez
3f360c6ef4
AP_BattMonitor: initial FMUv4pro support
2017-11-07 11:13:27 +09:00
Kevin Lopez Alvarez
f82dc7f12a
AP_Baro: initial FMUv4pro support
2017-11-07 11:13:24 +09:00
bnsgeyer
3b2c933306
Copter: heli: Update swashplate behavior
...
change swashplate behavior on ground in Acro, Stabilize, and AltHold
flight modes. See discussion here:
https://discuss.ardupilot.org/t/tradheli-swashplate-behavior-while-on-the-ground-and-potential-fix-to-issue-5396/22463/18
2017-11-06 17:02:25 +09:00
bnsgeyer
aec4045f91
AC_AttitudeControl: reset target attitude
...
added method to reset current vehicle attitude to support swash
behaviors in Trad Heli
2017-11-06 17:02:25 +09:00
Andrew Tridgell
2e11bef518
AP_Compass: merged compass changes from plane3.8
2017-11-06 16:56:02 +09:00
Andrew Tridgell
51e9091ca3
AP_Math: added rand_vec3f()
2017-11-06 16:55:59 +09:00
Lucas De Marchi
1d6b88ee68
AP_HAL_Linux: UARTDevice: never be the controlling terminal
...
If we are the controlling terminal for a tty device we will receive a
SIGHUP when the device disappears. Currently what happens is that we
simply stop the whole process. We don't want to fall off the sky due
to a bad device. This can happen for any reason, but it's more likely
if the UART is behind a USB connection.
2017-11-04 16:24:01 +09:00
Randy Mackay
78d1c55685
AP_Arming: check ahrs and gps differ by less than 10m
2017-11-04 16:02:43 +09:00
Randy Mackay
075564af2c
Copter: support SET_GPS_GLOBAL_ORIGIN
...
also remove setting of origin from DO_SET_HOME command
initialise ekf_origin location when consuming SET_GPS_GLOBAL_ORIGIN
set_ekf_origin performs sanity check on location
2017-11-04 15:53:18 +09:00
Randy Mackay
9a45940c25
GCS_MAVLink: add send_ekf_origin
2017-11-04 15:53:11 +09:00
bnsgeyer
d66a980be3
AP_Motors: TradHeli - fixed servo test function
2017-11-04 15:09:15 +09:00
Andrew Tridgell
29a8127fed
HAL_PX4: fixed a race condition on i2c init
...
we could call init on two devices with the same name, which caused
init_ok to be false. This could cause the SMBus battery to fail to
initialise
Thanks to Michael duBreuil for finding this!
2017-11-04 15:07:41 +09:00
Andrew Tridgell
61da180881
Copter: fixed motor runup check for heli
...
for all auto-throttle modes we should not allow a mode change to the
mode if the motor runup is not complete.
This moves the code to the set_mode() so it applies to all modes
fixes issue #6956
2017-11-04 15:06:04 +09:00
Andrew Tridgell
02f6f3b87b
Copter: fixed collective input with H_SV_MAN=1 for heli
...
when H_SV_MAN=1 we do direct pass-thru so the user can test swash
range. The problem is that it uses norm_input() for throttle, which
depends on RC3_TRIM. Nowhere else in heli or copter do we depend on
RC3_TRIM, so the user gets a misleading idea of behaviour when testing
their swash.
2017-11-04 15:05:58 +09:00
Lucas De Marchi
e37a084864
AP_HAL: change aerofc baud to 921600
...
(cherry picked from commit 2c72fc94ba
2017-10-19 15:16:55 -07:00
Lucas De Marchi
37144bde3c
PX4Firmware: aerofc-v1: add support to baud of 921600
2017-10-19 15:16:55 -07:00
Lucas De Marchi
6fe09cd3b8
PX4NuttX: add fix to stm32 flash
2017-10-19 15:16:55 -07:00
Randy Mackay
1a85c237cb
Copter: version to 3.5.3
2017-09-21 10:33:40 +09:00
Randy Mackay
9eb1db3dd2
Copter: 3.5.3 release notes
2017-09-21 10:33:05 +09:00
Randy Mackay
528d4d83d7
Copter: version to 3.5.3-rc1
2017-09-12 14:38:59 +09:00
Randy Mackay
ac108b31fa
Copter: 3.5.3-rc1 release notes
2017-09-12 14:38:31 +09:00
