moved ground start to first arming
added ground start flag
moved throttle_integrator to 50hz loop
CAMERA_STABILIZER deprecated - now always on
renamed current logging bit mask to match APM
added MA filter to PID - D term
Adjusted PIDs based on continued testing and new PID filter
added MASK_LOG_SET_DEFAULTS to match APM
moved some stuff out of ground start into system start where it belonged
Added slower Yaw gains for DCM when the copter is in the air
changed camera output to be none scaled PWM
fixed bug where ground_temperature was unfiltered
shortened Baro startup time
fixed issue with Nav_WP integrator not being reset
RTL no longer yaws towards home
Circle mode for flying a 10m circle around the point where it was engaged. - Not tested at all! Consider Circle mode as alpha.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2966 f9c3cf11-9bcb-44bc-f272-b75c42450872
this saves a little bit of code by moving the calculation of the
default log bitmask to compile time from runtime
(merge from APM)
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2887 f9c3cf11-9bcb-44bc-f272-b75c42450872
Added camera reversing parameters in AP_Var
Added RTL Throttle Hold set/check
Added dynamic speed control to slow down as you reach waypoints and RTL Home
upped Yaw Dead zone slightly.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2841 f9c3cf11-9bcb-44bc-f272-b75c42450872
Before: -> After
Stabilize P –> Stabilize P (Use NG values, or 8.3 x the older AC2 value)
Stabilize I –> Stabilize I (Stays same value)
Stabilize D –> Rate P (Stays same value)
–> Rate I (new)
Added a new value – an I term for rate. The old stabilization routines did not use this term. Please refer to the config.h file to read more about the new PIDs.
Added framework for using DCM corrected Accelerometer rates. Code is commented out for now.
Added set home at Arming.
Crosstrack is now a full PID loop, rather than just a P gain for more control.
Throttle now slews when switching out of Alt hold or Auto modes for less jarring transitions
Sonar and Baro PIDs are now combined into a throttle PID Yaw control is completely re-written.
Added Octa_Quad support - Max
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2836 f9c3cf11-9bcb-44bc-f272-b75c42450872
Slighted tuned down D term in Loiter PIDs after testing, tuned up P slightly
fixed alt hold bug cause when gaining 3D lock in alt hold.
Mavlink now reports correct throttle scaling value in mavlink
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2745 f9c3cf11-9bcb-44bc-f272-b75c42450872
Includes updated motor tests. These need to be verified.
Nav loiter D was added (.03) - verify this helps.
Nav_lat is now filtered for Rate control. This is to keep jerky pitching to a minimum.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2448 f9c3cf11-9bcb-44bc-f272-b75c42450872
updated motor setup test to be sequencial pulses of the motors in CW order.
Fixed Mission scripting logic
fixed Free yaw error in neutral throttle
fixed D term issue with Baro hold - was too high
incremented firmware revision, removed frame var
removed setup show from startup
removed unused EEPROM functions
fixed broken demo mission
fixed non working loiter with delay
git-svn-id: https://arducopter.googlecode.com/svn/trunk@2275 f9c3cf11-9bcb-44bc-f272-b75c42450872
The trunk is unstable, so please be careful. I've made a lot of changes based on the Sparkfun challange. Most include how we handle things like altitude, but the mission scripting has also been updated as well.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@1920 f9c3cf11-9bcb-44bc-f272-b75c42450872
turned off altitude interpolation for now.
removed the "Dampener" setting in config. Using less confusing kD instead.
removed throttle_cruise reset in events.pde for RTL - would cause a crash.
added I term for pitch/roll for when flying greater than 20°
git-svn-id: https://arducopter.googlecode.com/svn/trunk@1868 f9c3cf11-9bcb-44bc-f272-b75c42450872
Updated the motor spin up issue - this is the I've not set my radio up properly issue.
updated 200ms motor spin up issue with the Libraries - for those who have ESC's that don't do sanity checks.
git-svn-id: https://arducopter.googlecode.com/svn/trunk@1816 f9c3cf11-9bcb-44bc-f272-b75c42450872
jasonshort
tridge60@gmail.com
rmackay9@yahoo.com
mich146@hotmail.com
DrZiplok