Identify backend with an id, allowing other libraries to connect to
them. This is different from the _product_id member because it
identifies the sensor, not the board the sensor is in, which is
meaningless for our use case.
This allows backends to have a separate detection and initialization
logic. It doesn't change any backend yet and with the current code
there's no change in behavior either. This only allows
AP_InertialSensor::_detect_backend() to be called earlier so
AP_InertialSensor object can be used by other libraries. If it's not
called, later on AP_InertialSensor::init() will detect and start all
backends.
We were able to read only the block of registers that are part of the
data output from accelerometer/gyroscope. In order to support reading
the external sensors we need support for reading a generic block of
registers.
Now that we have a pre-arm check in place to detect bad lidar, the motion check is unnecessary and can false trigger for copters with flexible undercarriages or on uneven ground.
This param seems to have been un-implemented. This is putting it back in. Adds a meter offset to the calculated altitude form the baro sensors.
Also changes it from int8 to float
There are implementations for float, Vector2f and Vector3f for the Low
Pass Filter and the *2p filter. I tried to implement these filters
with one common template implementation. This implementation saves
some lines of code and reduced the redundancy. One could save even
more code if the currently overloaded isinf/isnan functions and checks
can be removed.
Signed-off-by: Daniel Frenzel <dgdanielf@gmail.com>
very strict check that all axis are not vibrating much at all
new param: INS_STILL_THRESH used to be a vibration threshold for different platforms
// @Description: Threshold to tolerate vibration to determine if vehicle is motionless. This depends on the frame type and if there is a constant vibration due to motors before launch or after landing. Total motionless is about 0.05. Suggested values: Planes/rover use 0.1, multirotors use 1, tradHeli uses 5
Param 1 denotes which direction the user expects the plane to
travel when changing altitude:
0 = no expectation, command completes when within 5 m of altitude.
1 = climb expected, command completes at or above altitude.
2 = descent expected, command completes at or below altitude.
This method checks for consistency between accelerometer readings and switches to the unit with the lowest vibration of the difference exceeds 0.3g
The threshold of 1.7 m/s/s corresponds to a maximum tilt error of 10 deg assuming one IMU is good, one is bad and the EKF is using the bad IMU.
Now instead of requiring the buffer to fill completely before we can
detect it is not draining, we use a time based mechanism to detect
when none of the first few bytes are transmitted after sitting in our
buffer a half second or more after flow control is enabled. This
huristic is reliable only for the first several chracters because we
believe that the radio must still have plenty of room in it's own
buffers at that time even if it is not able to transmit them to the
other radio yet. Note that the original algorithm made the same
assumption.
The new algorithm is especially helpful for cases where only keepalive
messages are transmitted before other packets can be requested by the
GCS. In this situation, the original code required almost 2 minutes
to disable flow control and allow communication with the GCS.
It was not only standardized, but actually fixed since ".." would not
move to the libraries/ directory (and hence the include location was
actually wrong).
This is really just calculating the hamming weight of the GNSS_MODE bitmask, but I don't know if the APM compiler could handle the GCC intrinsic that could calculate it faster, and this is done so rarely there isn't a significant penalty to using the for loop.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
This commit changes the way libraries headers are included in source files:
- If the header is in the same directory the source belongs to, so the
notation '#include ""' is used with the path relative to the directory
containing the source.
- If the header is outside the directory containing the source, then we use
the notation '#include <>' with the path relative to libraries folder.
Some of the advantages of such approach:
- Only one search path for libraries headers.
- OSs like Windows may have a better lookup time.
Lucas De Marchi
squilter
Paul Riseborough
Randy Mackay
Tom Pittenger
fillycheezstake
Leonard Hall
ziltoid2
dgrat
Andrew Tridgell
Michael Day
Brad Bosch
Fredrik Hedberg
Michael du Breuil
Gustavo Jose de Sousa