Randy Mackay
276b2dcf5e
Copter: move lost copter check to separate function
...
Also run from scheduler instead of from arm/disarm stick checks
Run at 10hz instead of 1hz
soundalarm_counter to uint8
Disable if equivalent aux switch is setup
Remove SEVERITY_LOW message because the GCSs never print these anyway
2015-04-29 00:05:03 +09:00
Julien Dubois
b7a6e3bf2c
Copter: fix update_thr_average to run at 100hz
...
Committed by Randy on Julien's behalf
2015-04-28 22:44:59 +09:00
Tom Pittenger
66c7090f00
Copter: fix compile warnings by converting .f to .0f
2015-04-24 14:24:52 +09:00
Randy Mackay
37e8d1a338
Copter: PosController alt limit from fence and EKF
2015-04-24 10:58:03 +09:00
Paul Riseborough
133b8f5ad7
Copter: Allow EKF to pull data from range finder object
2015-04-24 10:56:53 +09:00
Niels Joubert
704e75d140
ArduCopter: Remove kruft from old RTK driver
2015-04-24 08:01:32 +10:00
Randy Mackay
bfd24801ea
Copter: minor format fix
2015-04-21 21:47:19 +09:00
Arthur Benemann
7cf883a61c
Copter: increase the telemetry receive function rate to 400Hz
...
gimbal loop runs at 100Hz so to respond in time the gcs_check_input must run at a faster rate, the process are asyncronus
2015-04-21 21:45:31 +09:00
Randy Mackay
a27f383612
Copter: remove duplicate IMU/ATT logging
...
Previously IMU and ATT data could be logged at both a high rate
and a low rate. This patch makes it skip the low rate logging
if the high rate is enabled
2015-04-20 13:49:09 +09:00
Randy Mackay
dfb720bab6
Copter: rename FULL_IMU logging to IMU_FAST
...
This naming is consistent with the earlier ATTITUDE_FAST option and
clarifies that it's the rate that's increased rather than the content.
2015-04-20 13:49:04 +09:00
Randy Mackay
2dbff9c544
Copter: remove scheduler table for 100hz CPUs
...
We only support high performance CPUs capable of 400hz
2015-04-20 13:49:01 +09:00
Peter Barker
5a45de5e00
Copter: IMU full-rate logging LOG_BITMASK flag
2015-04-20 13:48:58 +09:00
Randy Mackay
1c6c03b0eb
Copter: firmware back to V3.3-dev
2015-04-18 11:51:53 +09:00
Jonathan Challinger
9a025024b5
Copter: use LowPassFilterVector3f for land detector accel filter
2015-04-17 10:46:56 +09:00
Jonathan Challinger
eafbd94d51
Copter: run land detector at 400hz
2015-04-17 10:46:53 +09:00
Leonard Hall
93d5c39248
Copter: add filter for the land detector
...
Individual access filtering will be replaced with a single 3-axis low pass
filter in the near future
2015-04-16 21:00:48 +09:00
Jonathan Challinger
e5a6023827
Copter: pass inertial_nav to fence
2015-04-14 16:10:03 +09:00
Randy Mackay
5a4039d99c
Copter: version to APM:Copter 3.3-rc1
2015-04-12 09:21:44 +09:00
Randy Mackay
b0c777259f
Copter: update home constantly while disarmed
2015-04-09 10:57:06 +09:00
Randy Mackay
2bec00e1c5
Copter: set ahrs home from ekf location
2015-04-09 10:57:02 +09:00
Randy Mackay
74b98b89d0
Copter: remove dcm check
2015-03-27 00:04:37 -07:00
Randy Mackay
522ef8f91f
Copter: rename MOT df msg to MOTB
...
This will slightly reduce confusion with the MOT message from AC3.1.5
that eventually became RCOUT
2015-03-18 21:25:45 +09:00
Randy Mackay
b679fd0be0
Copter: log RATE with ATT
2015-03-18 21:25:42 +09:00
Randy Mackay
e6c3f4f97b
Copter: move aux switch enum to defines.h
2015-03-17 21:18:49 +09:00
Robert Lefebvre
97cd3614eb
Copter: Change Aux Switch function list to enum.
2015-03-17 21:18:46 +09:00
Robert Lefebvre
a5af151a91
Copter: Initial expansion of Aux Switch to Ch7-12
2015-03-17 21:18:41 +09:00
Víctor Mayoral Vilches
79e152cd93
Copter: Update compass to the new interface
2015-03-13 18:46:16 +11:00
Randy Mackay
088a49abbf
Copter: remove APM1, APM2 support
2015-03-13 16:41:03 +09:00
Randy Mackay
fbfc94cf69
Copter: remove GPS glitch and failsafe
...
The EKF failsafe now captures all failures that could lead to a bad
position including GPS glitches and a bad compass meaning we do not need
this protection in the main flight code.
2015-03-13 16:40:46 +09:00
Randy Mackay
6f6847c025
Copter: use only InertialNav_EKF
...
remove calls to unsupported functions including ignore_next_error,
set_altitude, etc.
2015-03-13 16:40:37 +09:00
Randy Mackay
d7f624be39
Copter: remove baro_glitch protection
2015-03-13 16:40:27 +09:00
Leonard Hall
c537c38646
Copter: add update_throttle_low_comp
...
sets the priority of throttle vs attiude control so that attitude is
favoured (i.e. high throttle-low-comp) during dynamic flight while
throttle is favoured when vehicle may be landing.
2015-03-10 12:20:24 +09:00
Leonard Hall
d5bbe6de03
Copter: remove TRIM_THROTTLE
...
throttle_trim is replaced by throttle_average which is initialised to
the throttle_mid parameter value at startup
2015-03-06 14:02:19 +09:00
Leonard Hall
c78480e14f
Copter: rename loiter_pos to pos_xy
...
Also renamed throttle_rate to vel_z, throttle_accel to accel_z
2015-03-06 14:02:17 +09:00
Leonard Hall
e232867661
Copter: move LOITER_RATE to 2-axis PI controller
...
Also rename LOITER_RATE to VEL_XY for parameters, definitions, variables
2015-03-06 14:02:15 +09:00
Leonard Hall
8ba195a3a2
Copter: add Mot and Rate dataflash logging
2015-03-06 14:02:07 +09:00
Randy Mackay
bae424fa88
Copter: pass in loop_rate to motors constructor
2015-03-03 15:48:37 +09:00
Andrew Tridgell
7c975808f8
Copter: provide terrain height to rangefinder
...
used for power saving
2015-02-23 14:15:14 +11:00
Andrew Tridgell
191d803968
Copter: make PERF info message into a STATUSTEXT message
...
this makes it appear properly in tlogs. Also show both min and max
loop times
2015-02-16 10:02:53 +11:00
Randy Mackay
77d8f88e45
Copter: fence, rtl, land use alt-above-home
2015-02-12 15:08:00 +09:00
Randy Mackay
e081b9d1c7
Copter: home is set becomes three state
2015-02-12 15:00:50 +09:00
Randy Mackay
f4c392c64d
Copter: pre_arm_checks returns success or failure
...
This makes the pre-arm check function consist with the other arming
check functions
2015-02-02 22:31:11 +09:00
Randy Mackay
64af4ff923
Copter: rename set_servos_4 to motors_output
2015-02-02 22:31:08 +09:00
Robert Lefebvre
8e8ec09740
Copter: update pos_control alt_max from fence at 1hz
2015-01-30 14:13:49 +09:00
Randy Mackay
f91fb9a4e8
Copter: rename frsky_telemetry_send function
2015-01-29 14:05:14 +11:00
Randy Mackay
34503de18e
Copter: integrate SerialManager
...
Remove serial0, serial1 baud and protocol parameters
Pass serial_manager to GCS, GPS, mount, FrSky_telem objects during init
call SerialManager init_console on startup
use SerialManager's set_block_writes_all
2015-01-29 14:05:14 +11:00
Randy Mackay
c51ba8cd03
Copter: integrate mount frontend-backend restructure
...
initialise mount on startup
use Mount::has_pan_control method
Remove calls to unimplemented mount.configure_cmd
Remove call to update_mount_type which will be handled from within mount
lib
2015-01-29 13:57:18 +11:00
Randy Mackay
58ac9de94b
Copter: update home position when disarmed
...
This resolves the issue in which the vehicle's position jumped back to
it's home location when disarmed and using the EKF. This also makes
copter consistent with plane.
2015-01-22 14:39:50 +09:00
Randy Mackay
e94693e8ac
Copter: remove unused throttle integrator
2015-01-21 14:38:06 +09:00
Robert Lefebvre
b8822a42b6
Copter: Change Compass logging to new DataFlash method that handles instances.
2015-01-21 14:37:52 +09:00
