priseborough
963cc4d60a
Copter: Add velocity gain scaler to interfaces
...
Allows nav gain to be scaled to compensate for optical flow noise
2014-12-06 18:16:50 +11:00
priseborough
9e7709fa09
Copter: Expand EKF speed limit public method to handle control limits
2014-12-06 18:16:50 +11:00
priseborough
9844dacf40
Copter: Add EKF ground speed limit to loiter speed control
...
This is required to prevent the speed controller saturating the optical flow sensor during low altitude flying.
2014-12-06 18:16:50 +11:00
priseborough
715d64dce9
Copter: Check for new optical flow updates at 200Hz
...
Supports use of higher flow read rates if required.
2014-12-06 18:16:48 +11:00
priseborough
468c83c074
Copter : Check for new optical flow readings every 10ms
...
The driver polls the sensor asynchronously every 100 msec, so we need to continually check for new data.
2014-12-06 18:16:48 +11:00
priseborough
be54f2d6ee
Copter : Don't force pre-compiler inclusion of optical flow
2014-12-06 18:16:48 +11:00
priseborough
6d5fb33d1a
Copter : enable optical flow by default
2014-12-06 18:16:47 +11:00
priseborough
45c007d216
Copter : Correct comment on required optical flow update rate
2014-12-06 18:16:47 +11:00
priseborough
a72b6b179b
Copter : Modify EKF optical flow data interface
2014-12-06 18:16:46 +11:00
priseborough
311206017c
Copter : Update EKF optical flow data interface
...
Makes it compatible with the new PX4Flow interface
2014-12-06 18:16:46 +11:00
priseborough
267ef48026
Copter : disable tilt correction of range finder data for use by EKF
...
This is a temporary fix. We need to make separate range and altitude measurements available.
2014-12-06 18:16:45 +11:00
priseborough
27f9289391
Copter : Add range finder measurements to EKF optical flow data
2014-12-06 18:16:44 +11:00
priseborough
635e593d55
Copter : temporary mods to test use of flow sensor internal gyro data
2014-12-06 18:16:44 +11:00
priseborough
34249ffa42
Copter : EKF optical flow fusion support preliminary changes
...
Assumes optflow sensor has been modified to push data at a low rate, eg 10Hz
and velocity data is angular velocity, not linear velocity
2014-12-06 18:16:44 +11:00
Randy Mackay
8b80e58861
Copter: enable OPTFLOW - do not merge to master
2014-12-06 18:16:44 +11:00
priseborough
60527a023a
Copter : Update optical flow test for new PX4Flow interface
2014-12-06 18:16:43 +11:00
priseborough
0d7555b259
Copter : Remove legacy optical flow control mode
...
This mode is not compatible with the new PX4Flow interface
2014-12-06 18:16:43 +11:00
priseborough
900519b35b
Copter : Remove legacy optical flow control mode
...
This mode is not compatible with the new PX4Flow interface
2014-12-06 18:16:43 +11:00
priseborough
23953b459e
Copter : Update logging for new PX4Flow sensor interface
2014-12-06 18:16:43 +11:00
priseborough
20e715aa13
Copter : Remove ADNS3080 flow sensor support
2014-12-06 18:16:43 +11:00
priseborough
5ef2208017
Copter: Change flow sensor read sample rate to 10Hz
2014-12-06 18:16:43 +11:00
Randy Mackay
7be78621f4
Copter: run_nav_updates at 50hz on Pixhawk, 25hz on APM2
...
Based on work by Jon Challinger (see earlier commit)
2014-12-05 14:01:16 +09:00
Jonathan Challinger
203b713f0d
Copter: run_nav_updates at 100hz on pixhawk
2014-12-05 14:01:14 +09:00
Andrew Tridgell
dcdfff66e8
Copter: setup pwm esc scaling
2014-11-26 11:14:44 +11:00
Randy Mackay
13b8159fb5
Copter: only allow one preflight calibration at a time
2014-11-21 22:00:45 +09:00
Randy Mackay
330b52194f
Copter: change to switch order in guided spline
...
No functional change
2014-11-19 12:06:30 -08:00
Arthur Benemann
db89bd6f03
Copter: correct frame/location of guided spline
2014-11-19 11:59:13 -08:00
Randy Mackay
84f82dd129
Copter: correct get_pilot_desired_throttle calc
...
Also minor format and commenting addition
2014-11-17 18:16:14 -08:00
Jonathan Challinger
3a529b2cef
Copter: utilize get_control_mid for throttle calculations
2014-11-17 18:16:11 -08:00
Andrew Tridgell
b6c06ab691
Copter: fix build with new mavlink repo
2014-11-18 11:20:04 +11:00
Randy Mackay
c6e70179d2
Copter: move MOUNT_STATUS lower in GCS_MAVLink
...
No functional change
2014-11-17 15:59:41 -08:00
Arthur Benemann
6bee8969a1
Copter: append MOUNT_STATUS message to STREAM_EXTRA3 messages
...
The msg is now periodically sent to the GCS, instead of only on request.STREAM_EXTRA3
2014-11-17 15:59:26 -08:00
Jonathan Challinger
387f3276cb
Copter: handle SET_POSITION_TARGET mavlink messages
2014-11-17 14:38:55 -08:00
Jonathan Challinger
1b1327dc93
Copter: add Guided_Spline mode
2014-11-17 14:38:48 -08:00
Jonathan Challinger
e7939cca01
Copter: change function definitions in guided to static
2014-11-17 14:38:43 -08:00
Jonathan Challinger
c7a38c4350
Copter: use force_descend option on auto landings
2014-11-13 18:40:42 -08:00
Craig Elder
f7d0a930c2
Copter: Updated GCS_FAILSAFE Parameter Description
2014-11-13 13:10:06 -08:00
Arthur Benemann
f24f5a6a32
Copter: remove call to camera.configure and control
...
The do_take_picture() function must be called for logging to occur.
configure_msg is empty at the moment so the call to this is remove
2014-11-11 10:31:49 -08:00
Randy Mackay
ed099a73a3
Copter: minor rename of ACRO circular limits variable
2014-11-10 18:36:17 -08:00
Randy Mackay
83051c306d
Copter: minor rename of a circular limits variable
2014-11-10 18:36:15 -08:00
Jolyon Saunders
a9205e1032
Copter: Add circular limits to ACRO
2014-11-10 18:36:13 -08:00
Jolyon Saunders
d46c659d0f
Copter: Add circular limits pilot's roll/pitch inputs
2014-11-10 18:36:10 -08:00
Randy Mackay
b2badee172
Copter: reset baro glitch after baro init
2014-11-09 13:34:17 -08:00
Randy Mackay
9e12b01569
Copter: CPU failsafe set motors to min before logging error
...
This ensures that if the logging stalls the motors will have already
been reduced to zero
2014-11-08 11:37:23 +09:00
Jonathan Challinger
80ba40d149
Copter: CPU failsafe logs an error
2014-11-08 11:27:16 +09:00
Jonathan Challinger
e37337b744
Copter: remove gyro cal prearm check
2014-11-07 14:02:26 +09:00
Randy Mackay
9f2af783db
Copter: update AC3.2 ReleaseNotes
2014-11-07 14:00:00 +09:00
Randy Mackay
1b64dd2280
Copter: clarify pv_location_to_vector param name
...
Also update function description
2014-11-06 11:53:57 +09:00
Clay McClure
a897c14255
Copter: ensure lat, lon, alt all zero is handled
...
Use default position when waypoint lat/lon are zero,
and default altitude when waypoint alt is zero, for
both spline and straight-line waypoints.
Fixes #1145 .
2014-11-06 11:53:32 +09:00
Randy Mackay
07975ed564
Copter: minor reformat of control_autotune
2014-11-05 21:08:39 +09:00
