mirror of https://github.com/ArduPilot/ardupilot
AP_HAL_ChibiOS: iFlight Blitz H7 Pro
This commit is contained in:
Andy Piper
Andrew Tridgell
parent
1ff8549cc3
commit
a707fde4bf
|
|
@ -0,0 +1,113 @@
|
||||||
|
# iFlight BLITZ H7 Pro Flight Controller
|
||||||
|
|
||||||
|
The Blitz H7 Pro is a flight controller produced by [iFlight](https://shop.iflight-rc.com/).
|
||||||
|
|
||||||
|
## Features
|
||||||
|
|
||||||
|
- MCU - STM32H743 32-bit processor running at 480 MHz
|
||||||
|
- Gyro: ICM42688
|
||||||
|
- 32Gb SDCard for logging
|
||||||
|
- BEC output: 5V 2.5A, switch controlled 12v 2A
|
||||||
|
- Barometer: DPS310
|
||||||
|
- OSD: AT7456E
|
||||||
|
- 7x UARTs
|
||||||
|
- 13x PWM Outputs (12 Motor Output, 1 LED)
|
||||||
|
- Battery input voltage: 2S-8S
|
||||||
|
- 2x I2C for external compass, airspeed, etc.
|
||||||
|
- CAN port
|
||||||
|
|
||||||
|
## Pinout
|
||||||
|
|
||||||
|
|
||||||
|
|
||||||
|
back side pinout image pending from iFlight
|
||||||
|
|
||||||
|
The expansion connector provides access to the following pins:
|
||||||
|
- CAN+/CAN-
|
||||||
|
- M9 through M12
|
||||||
|
- TX7/RX7
|
||||||
|
- SCL2/SDA2
|
||||||
|
- RSSI
|
||||||
|
- 5V/12V/GND
|
||||||
|
|
||||||
|
## UART Mapping
|
||||||
|
|
||||||
|
The UARTs are marked Rn and Tn in the above pinouts. The Rn pin is the
|
||||||
|
receive pin for UARTn. The Tn pin is the transmit pin for UARTn.
|
||||||
|
|Name|Pin|Function|
|
||||||
|
|:-|:-|:-|
|
||||||
|
|SERIAL0|COMPUTER|USB|
|
||||||
|
|SERIAL1|RX1/TX1|UART1 (DJI connector, DMA-enabled)|
|
||||||
|
|SERIAL2|TX2/RX2|UART2 (RX, DMA-enabled)|
|
||||||
|
|SERIAL3|TX3/RX3|UART3 (DMA-enabled)|
|
||||||
|
|SERIAL4|TX4/RX4|UART4 (GPS, DMA-enabled)|
|
||||||
|
|SERIAL5|RX5|UART5 (ESC Telemetry)|
|
||||||
|
|SERIAL6|TX6/RX6|UART6|
|
||||||
|
|SERIAL7|TX7/RX7|UART7|
|
||||||
|
|
||||||
|
## RC Input
|
||||||
|
|
||||||
|
RC input is configured on the (UART2_RX/UART2_TX) pins which forms part of the DJI connector. It supports all serial RC protocols.
|
||||||
|
|
||||||
|
## OSD Support
|
||||||
|
|
||||||
|
The BLITZ H7 Pro supports OSD using OSD_TYPE 1 (MAX7456 driver).
|
||||||
|
|
||||||
|
## PWM Output
|
||||||
|
|
||||||
|
The BLITZ H7 Pro has 13 PWM outputs. The pads for motor output M1-M4 are in one ESC connector and M5-M8 in the second ESC connector. The remaining outputs are on the pads on the daughterboard. The first 8 outputs support bi-directional DShot and DShot, as well as all PWM types. Outputs 9-10 support DShot, as well as all PWM types and outputs 11-12 only support PWM.
|
||||||
|
|
||||||
|
The PWM are in in five groups:
|
||||||
|
|
||||||
|
- PWM 1-2 in group1
|
||||||
|
- PWM 3-6 in group2
|
||||||
|
- PWM 7-10 in group3
|
||||||
|
- PWM 11-12 in group4
|
||||||
|
- PWM 13 in group5
|
||||||
|
.. note:: for users migrating from BetaflightX quads, the first four outputs M1-M4 have been configured for use with existing motor wiring using these default parameters:
|
||||||
|
|
||||||
|
- :ref:`FRAME_CLASS<FRAME_CLASS>` = 1 (Quad)
|
||||||
|
- :ref:`FRAME_TYPE<FRAME_TYPE>` = 12 (BetaFlightX)
|
||||||
|
|
||||||
|
|
||||||
|
Channels within the same group need to use the same output rate. If
|
||||||
|
any channel in a group uses DShot then all channels in the group need
|
||||||
|
to use DShot.
|
||||||
|
|
||||||
|
Video Power Control
|
||||||
|
================
|
||||||
|
|
||||||
|
The 12V video power can be turned off/on using GPIO 81 which is already assigned by default to RELAY2. This relay can be controlled either from the GCS or using a transmitter channel (See :ref:`common-auxiliary-functions`)
|
||||||
|
RSSI
|
||||||
|
====
|
||||||
|
|
||||||
|
Analog RSSI pin is "4"
|
||||||
|
|
||||||
|
## Battery Monitoring
|
||||||
|
|
||||||
|
The board has a builtin voltage sensor and a current sensor input tied to its 4 in 1 ESC current sensor. The voltage sensor can handle up to 6S
|
||||||
|
LiPo batteries.
|
||||||
|
|
||||||
|
The correct battery setting parameters are:
|
||||||
|
|
||||||
|
- BATT_MONITOR 4
|
||||||
|
- BATT_VOLT_PIN 10
|
||||||
|
- BATT_VOLT_MULT 11
|
||||||
|
- BATT_CURR_PIN 11
|
||||||
|
- BATT_CURR_MULT 50
|
||||||
|
|
||||||
|
These are set by default in the firmware and shouldn't need to be adjusted
|
||||||
|
|
||||||
|
## Compass
|
||||||
|
|
||||||
|
The BLITZ H7 Pro does not have a builtin compass, but you can attach an external compass to I2C pins.
|
||||||
|
|
||||||
|
## Loading Firmware
|
||||||
|
|
||||||
|
Initial firmware load can be done with DFU by plugging in USB with the
|
||||||
|
bootloader button pressed. Then you should load the "with_bl.hex"
|
||||||
|
firmware, using your favourite DFU loading tool.
|
||||||
|
|
||||||
|
Once the initial firmware is loaded you can update the firmware using
|
||||||
|
any ArduPilot ground station software. Updates should be done with the
|
||||||
|
*.apj firmware files.
|
||||||
Binary file not shown.
|
After Width: | Height: | Size: 541 KiB |
|
|
@ -0,0 +1,3 @@
|
||||||
|
# setup for LEDs on chan9
|
||||||
|
SERVO13_FUNCTION 120
|
||||||
|
NTF_LED_TYPES 257
|
||||||
|
|
@ -0,0 +1,45 @@
|
||||||
|
|
||||||
|
# hw definition file for processing by chibios_hwdef.py
|
||||||
|
# for IFLIGHT_BLITZ_H7_PRO hardware.
|
||||||
|
# thanks to betaflight for pin information
|
||||||
|
|
||||||
|
# MCU class and specific type
|
||||||
|
MCU STM32H7xx STM32H743xx
|
||||||
|
|
||||||
|
# board ID for firmware load
|
||||||
|
APJ_BOARD_ID AP_HW_BlitzH7Pro
|
||||||
|
|
||||||
|
# crystal frequency, setup to use external oscillator
|
||||||
|
OSCILLATOR_HZ 8000000
|
||||||
|
|
||||||
|
FLASH_SIZE_KB 2048
|
||||||
|
|
||||||
|
# bootloader starts at zero offset
|
||||||
|
FLASH_RESERVE_START_KB 0
|
||||||
|
|
||||||
|
# the location where the bootloader will put the firmware
|
||||||
|
FLASH_BOOTLOADER_LOAD_KB 384
|
||||||
|
|
||||||
|
# order of UARTs (and USB)
|
||||||
|
SERIAL_ORDER OTG1
|
||||||
|
|
||||||
|
# PA10 IO-debug-console
|
||||||
|
PA11 OTG_FS_DM OTG1
|
||||||
|
PA12 OTG_FS_DP OTG1
|
||||||
|
|
||||||
|
PA13 JTMS-SWDIO SWD
|
||||||
|
PA14 JTCK-SWCLK SWD
|
||||||
|
|
||||||
|
# default to all pins low to avoid ESD issues
|
||||||
|
DEFAULTGPIO OUTPUT LOW PULLDOWN
|
||||||
|
|
||||||
|
|
||||||
|
# Chip select pins
|
||||||
|
PB12 OSD1_CS CS
|
||||||
|
PC15 GYRO1_CS CS
|
||||||
|
PE11 GYRO2_CS CS
|
||||||
|
|
||||||
|
PA8 LED_BOOTLOADER OUTPUT LOW
|
||||||
|
define HAL_LED_ON 0
|
||||||
|
|
||||||
|
PD10 VTX_PWR OUTPUT GPIO(81) HIGH
|
||||||
|
|
@ -0,0 +1,184 @@
|
||||||
|
|
||||||
|
# hw definition file for processing by chibios_hwdef.py
|
||||||
|
# for IFLIGHT_BLITZ_H7_PRO hardware.
|
||||||
|
# thanks to betaflight for pin information
|
||||||
|
|
||||||
|
# MCU class and specific type
|
||||||
|
MCU STM32H7xx STM32H743xx
|
||||||
|
|
||||||
|
# board ID for firmware load
|
||||||
|
APJ_BOARD_ID AP_HW_BlitzH7Pro
|
||||||
|
|
||||||
|
# crystal frequency, setup to use external oscillator
|
||||||
|
OSCILLATOR_HZ 8000000
|
||||||
|
|
||||||
|
MCU_CLOCKRATE_MHZ 480
|
||||||
|
|
||||||
|
FLASH_SIZE_KB 2048
|
||||||
|
|
||||||
|
FLASH_RESERVE_START_KB 384
|
||||||
|
|
||||||
|
define HAL_STORAGE_SIZE 16384
|
||||||
|
define STORAGE_FLASH_PAGE 1
|
||||||
|
|
||||||
|
# ChibiOS system timer
|
||||||
|
STM32_ST_USE_TIMER 12
|
||||||
|
define CH_CFG_ST_RESOLUTION 16
|
||||||
|
|
||||||
|
# SPI devices
|
||||||
|
|
||||||
|
# SPI1
|
||||||
|
PA5 SPI1_SCK SPI1
|
||||||
|
PA6 SPI1_MISO SPI1
|
||||||
|
PD7 SPI1_MOSI SPI1
|
||||||
|
|
||||||
|
# SPI2
|
||||||
|
PB13 SPI2_SCK SPI2
|
||||||
|
PB14 SPI2_MISO SPI2
|
||||||
|
PB15 SPI2_MOSI SPI2
|
||||||
|
|
||||||
|
# Chip select pins
|
||||||
|
PB12 OSD1_CS CS
|
||||||
|
PC15 GYRO1_CS CS
|
||||||
|
PE11 GYRO2_CS CS
|
||||||
|
|
||||||
|
# Beeper
|
||||||
|
PA15 TIM2_CH1 TIM2 GPIO(32) ALARM
|
||||||
|
|
||||||
|
# SERIAL ports
|
||||||
|
SERIAL_ORDER OTG1 USART1 USART2 USART3 UART4 USART6 UART7 UART8 OTG2
|
||||||
|
# PA10 IO-debug-console
|
||||||
|
PA11 OTG_FS_DM OTG1
|
||||||
|
PA12 OTG_FS_DP OTG1
|
||||||
|
|
||||||
|
# USART1 - VTX
|
||||||
|
PA10 USART1_RX USART1
|
||||||
|
PA9 USART1_TX USART1
|
||||||
|
define DEFAULT_SERIAL1_PROTOCOL SerialProtocol_MSP_DisplayPort
|
||||||
|
|
||||||
|
# USART2 - RX
|
||||||
|
PD5 USART2_TX USART2
|
||||||
|
PD6 USART2_RX USART2
|
||||||
|
define DEFAULT_SERIAL2_PROTOCOL SerialProtocol_RCIN
|
||||||
|
|
||||||
|
# USART3
|
||||||
|
PD8 USART3_TX USART3
|
||||||
|
PD9 USART3_RX USART3
|
||||||
|
define DEFAULT_SERIAL3_PROTOCOL SerialProtocol_None
|
||||||
|
|
||||||
|
# UART4 - GPS
|
||||||
|
PB8 UART4_RX UART4
|
||||||
|
PB9 UART4_TX UART4
|
||||||
|
define DEFAULT_SERIAL4_PROTOCOL SerialProtocol_GPS
|
||||||
|
|
||||||
|
# USART6
|
||||||
|
PC6 USART6_TX USART6 NODMA
|
||||||
|
PC7 USART6_RX USART6 NODMA
|
||||||
|
define DEFAULT_SERIAL5_PROTOCOL SerialProtocol_ESCTelemetry
|
||||||
|
|
||||||
|
# UART7
|
||||||
|
PE7 UART7_RX UART7 NODMA
|
||||||
|
PE8 UART7_TX UART7 NODMA
|
||||||
|
# Not pinned out
|
||||||
|
PE9 UART7_RTS UART7
|
||||||
|
PE10 UART7_CTS UART7
|
||||||
|
|
||||||
|
# UART8
|
||||||
|
PE0 UART8_RX UART8 NODMA
|
||||||
|
PE1 UART8_TX UART8 NODMA
|
||||||
|
|
||||||
|
# I2C ports
|
||||||
|
I2C_ORDER I2C1 I2C2
|
||||||
|
# I2C1
|
||||||
|
PB6 I2C1_SCL I2C1
|
||||||
|
PB7 I2C1_SDA I2C1
|
||||||
|
|
||||||
|
# I2C2
|
||||||
|
PB10 I2C2_SCL I2C2
|
||||||
|
PB11 I2C2_SDA I2C2
|
||||||
|
|
||||||
|
# microSD support
|
||||||
|
PC8 SDMMC1_D0 SDMMC1
|
||||||
|
PC9 SDMMC1_D1 SDMMC1
|
||||||
|
PC10 SDMMC1_D2 SDMMC1
|
||||||
|
PC11 SDMMC1_D3 SDMMC1
|
||||||
|
PC12 SDMMC1_CK SDMMC1
|
||||||
|
PD2 SDMMC1_CMD SDMMC1
|
||||||
|
|
||||||
|
define HAL_OS_FATFS_IO 1
|
||||||
|
|
||||||
|
# CAN
|
||||||
|
PD0 CAN1_RX CAN1
|
||||||
|
PD1 CAN1_TX CAN1
|
||||||
|
PD3 GPIO_CAN1_SILENT OUTPUT PUSHPULL SPEED_LOW LOW GPIO(70)
|
||||||
|
|
||||||
|
# VTX power
|
||||||
|
PD10 VTX_PWR OUTPUT GPIO(81) HIGH
|
||||||
|
define RELAY2_PIN_DEFAULT 81
|
||||||
|
|
||||||
|
# ADC ports
|
||||||
|
|
||||||
|
# ADC1
|
||||||
|
PC0 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
||||||
|
define HAL_BATT_VOLT_PIN 10
|
||||||
|
define HAL_BATT_VOLT_SCALE 11.0
|
||||||
|
PC1 BATT_CURRENT_SENS ADC1 SCALE(1)
|
||||||
|
define HAL_BATT_CURR_PIN 11
|
||||||
|
define HAL_BATT_CURR_SCALE 50.0
|
||||||
|
PC5 RSSI_ADC ADC1
|
||||||
|
define BOARD_RSSI_ANA_PIN 8
|
||||||
|
define HAL_BATT_MONITOR_DEFAULT 4
|
||||||
|
PC4 PRESSURE_SENS ADC1 SCALE(2)
|
||||||
|
define HAL_DEFAULT_AIRSPEED_PIN 4
|
||||||
|
|
||||||
|
# MOTORS
|
||||||
|
PB0 TIM3_CH3 TIM3 PWM(1) GPIO(50) BIDIR # M1
|
||||||
|
PB1 TIM3_CH4 TIM3 PWM(2) GPIO(51) # M2
|
||||||
|
PA0 TIM5_CH1 TIM5 PWM(3) GPIO(52) BIDIR # M3
|
||||||
|
PA1 TIM5_CH2 TIM5 PWM(4) GPIO(53) # M4
|
||||||
|
PA2 TIM5_CH3 TIM5 PWM(5) GPIO(54) BIDIR # M5
|
||||||
|
PA3 TIM5_CH4 TIM5 PWM(6) GPIO(55) # M6
|
||||||
|
PD12 TIM4_CH1 TIM4 PWM(7) GPIO(56) BIDIR # M7
|
||||||
|
PD13 TIM4_CH2 TIM4 PWM(8) GPIO(57) # M8
|
||||||
|
# Motor outputs on daughterboard
|
||||||
|
PD14 TIM4_CH3 TIM4 PWM(9) GPIO(58) # M9
|
||||||
|
PD15 TIM4_CH4 TIM4 PWM(10) GPIO(59) # M10
|
||||||
|
PE5 TIM15_CH1 TIM15 PWM(11) GPIO(60) NODMA # M11
|
||||||
|
PE6 TIM15_CH2 TIM15 PWM(12) GPIO(61) NODMA # M12
|
||||||
|
|
||||||
|
# LEDs
|
||||||
|
PA8 TIM1_CH1 TIM1 PWM(13) GPIO(62) # M9
|
||||||
|
|
||||||
|
PE3 LED0 OUTPUT LOW GPIO(90)
|
||||||
|
define HAL_GPIO_A_LED_PIN 90
|
||||||
|
|
||||||
|
PE4 LED1 OUTPUT LOW GPIO(91)
|
||||||
|
define HAL_GPIO_B_LED_PIN 91
|
||||||
|
|
||||||
|
# OSD setup
|
||||||
|
SPIDEV osd SPI2 DEVID1 OSD1_CS MODE0 10*MHZ 10*MHZ
|
||||||
|
|
||||||
|
define OSD_ENABLED 1
|
||||||
|
define HAL_OSD_TYPE_DEFAULT 1
|
||||||
|
ROMFS_WILDCARD libraries/AP_OSD/fonts/font*.bin
|
||||||
|
|
||||||
|
# Barometer setup
|
||||||
|
BARO DPS310 I2C:1:0x76
|
||||||
|
|
||||||
|
# IMU setup
|
||||||
|
SPIDEV imu1 SPI1 DEVID1 GYRO1_CS MODE3 1*MHZ 16*MHZ
|
||||||
|
|
||||||
|
IMU Invensensev3 SPI:imu1 ROTATION_ROLL_180
|
||||||
|
|
||||||
|
DMA_NOSHARE TIM3_UP TIM5_UP TIM4_UP SPI1*
|
||||||
|
DMA_PRIORITY TIM3_UP TIM5_UP TIM4_UP SPI1*
|
||||||
|
|
||||||
|
# no built-in compass, but probe the i2c bus for all possible
|
||||||
|
# external compass types
|
||||||
|
define ALLOW_ARM_NO_COMPASS
|
||||||
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
||||||
|
define HAL_I2C_INTERNAL_MASK 0
|
||||||
|
define HAL_COMPASS_AUTO_ROT_DEFAULT 2
|
||||||
|
define HAL_DEFAULT_INS_FAST_SAMPLE 1
|
||||||
|
# Motor order implies Betaflight/X for standard ESCs
|
||||||
|
define HAL_FRAME_TYPE_DEFAULT 12
|
||||||
Loading…
Reference in New Issue