HAL_ChibiOS: added hwdef.dat for f103-periph

libraries/AP_HAL_ChibiOS/hwdef/f103-periph/hwdef-bl.dat

@@ -0,0 +1,99 @@
+# hw definition file for processing by chibios_pins.py
+
+# MCU class and specific type
+MCU STM32F103 STM32F103xB
+
+FLASH_RESERVE_START_KB 0
+FLASH_BOOTLOADER_LOAD_KB 25
+
+# board ID for firmware load
+APJ_BOARD_ID 3
+
+# crystal frequency
+OSCILLATOR_HZ 8000000
+
+define STM32_SW                            STM32_SW_PLL
+define STM32_PLLSRC                        STM32_PLLSRC_HSE
+define STM32_PLLXTPRE                      STM32_PLLXTPRE_DIV1
+define STM32_PLLMUL_VALUE                  9
+define STM32_PPRE1                         STM32_PPRE1_DIV2
+define STM32_PPRE2                         STM32_PPRE2_DIV2
+define STM32_ADCPRE                        STM32_ADCPRE_DIV4
+
+define CH_CFG_ST_FREQUENCY 1000
+
+# assume 128k flash part
+FLASH_SIZE_KB 128
+
+STDOUT_SERIAL SD1
+STDOUT_BAUDRATE 57600
+
+# board voltage
+STM32_VDD 330U
+
+# order of UARTs
+UART_ORDER USART1
+define HAL_USE_UART FALSE
+
+PA4 LED_BOOTLOADER OUTPUT LOW
+define HAL_LED_ON 1
+
+# USART1
+PA9  USART1_TX USART1 SPEED_HIGH
+PA10 USART1_RX USART1 SPEED_HIGH
+
+# USART2
+PA2 USART2_TX USART2 SPEED_HIGH
+PA3 USART2_RX USART2 SPEED_HIGH
+
+define HAL_USE_SERIAL TRUE
+
+define STM32_SERIAL_USE_USART1 TRUE
+define STM32_SERIAL_USE_USART2 TRUE
+define STM32_SERIAL_USE_USART3 FALSE
+
+define HAL_NO_GPIO_IRQ
+define CH_CFG_ST_TIMEDELTA 0
+#define CH_CFG_USE_DYNAMIC FALSE
+define SERIAL_BUFFERS_SIZE 32
+define HAL_USE_EMPTY_IO TRUE
+define PORT_INT_REQUIRED_STACK 64
+
+# avoid timer and RCIN threads to save memory
+define HAL_NO_TIMER_THREAD
+define HAL_NO_RCIN_THREAD
+
+#defined to turn off undef warnings
+define __FPU_PRESENT 0
+
+define HAL_USE_RTC FALSE
+define DISABLE_SERIAL_ESC_COMM TRUE
+define NO_DATAFLASH TRUE
+
+define DMA_RESERVE_SIZE 0
+
+define PERIPH_FW TRUE
+MAIN_STACK 0x800
+PROCESS_STACK 0x800
+define HAL_DISABLE_LOOP_DELAY
+
+define HAL_USE_EMPTY_STORAGE 1
+define HAL_STORAGE_SIZE 16384
+
+# enable CAN support
+PA11 CAN_RX CAN
+PA12 CAN_TX CAN
+define HAL_USE_CAN TRUE
+define STM32_CAN_USE_CAN1 TRUE
+
+# make bl baudrate match debug baudrate for easier debugging
+define BOOTLOADER_BAUDRATE 57600
+
+# use a small bootloader timeout
+define HAL_BOOTLOADER_TIMEOUT 1000
+
+# use PB6 (normally I2C1_SCL) as "hold in bootloader" pin
+# this has a hw pullup, so if we set it as input floating
+# and look for it low then we know user has pulled it down and
+# want to stay in the bootloader
+PB6 STAY_IN_BOOTLOADER INPUT FLOATING

libraries/AP_HAL_ChibiOS/hwdef/f103-periph/hwdef.dat

@@ -0,0 +1,133 @@
+# hw definition file for processing by chibios_pins.py
+
+# MCU class and specific type
+MCU STM32F103 STM32F103xB
+
+# bootloader starts firmware at 25k
+FLASH_RESERVE_START_KB 25
+
+# store parameters in pages 23 and 24
+define STORAGE_FLASH_PAGE 23
+define HAL_STORAGE_SIZE 800
+
+# board ID for firmware load
+APJ_BOARD_ID 3
+
+# crystal frequency
+OSCILLATOR_HZ 8000000
+
+define CH_CFG_ST_FREQUENCY 1000
+
+# assume the 128k flash part for now
+FLASH_SIZE_KB 128
+
+# board voltage
+STM32_VDD 330U
+
+# order of UARTs
+UART_ORDER USART2 USART1
+
+# a LED to flash
+PA4 LED OUTPUT LOW
+
+# USART1, connected to GPS
+PA9  USART1_TX USART1 SPEED_HIGH NODMA
+PA10 USART1_RX USART1 SPEED_HIGH NODMA
+
+# USART2 for debug
+PA2 USART2_TX USART2 SPEED_HIGH NODMA
+PA3 USART2_RX USART2 SPEED_HIGH NODMA
+
+define HAL_UART_NODMA
+
+# only one I2C bus in normal config
+PB6 I2C1_SCL I2C1
+PB7 I2C1_SDA I2C1
+
+PB0 MAG_CS CS
+
+# spi bus for compass
+PA5 SPI1_SCK SPI1
+PA6 SPI1_MISO SPI1
+PA7 SPI1_MOSI SPI1
+
+SPIDEV rm3100 SPI1 DEVID1 MAG_CS MODE0 1*MHZ 1*MHZ
+
+# analog input
+# PA5 VIN5 ADC1
+define HAL_USE_ADC TRUE
+define STM32_ADC_USE_ADC1 TRUE
+define HAL_DISABLE_ADC_DRIVER TRUE
+
+define HAL_NO_GPIO_IRQ
+define CH_CFG_ST_TIMEDELTA 0
+#define CH_CFG_USE_DYNAMIC FALSE
+define SERIAL_BUFFERS_SIZE 512
+define PORT_INT_REQUIRED_STACK 64
+
+# avoid timer and RCIN threads to save memory
+define HAL_NO_TIMER_THREAD
+define HAL_NO_RCIN_THREAD
+
+#defined to turn off undef warnings
+define __FPU_PRESENT 0
+
+define HAL_USE_RTC FALSE
+define DISABLE_SERIAL_ESC_COMM TRUE
+define NO_DATAFLASH TRUE
+
+define DMA_RESERVE_SIZE 0
+
+define PERIPH_FW TRUE
+
+# MAIN_STACK is stack of initial thread
+MAIN_STACK 0x100
+
+# PROCESS_STACK controls stack for main thread
+PROCESS_STACK 0x600
+define HAL_DISABLE_LOOP_DELAY
+
+# enable CAN support
+PA11 CAN_RX CAN
+PA12 CAN_TX CAN
+define HAL_USE_CAN TRUE
+define STM32_CAN_USE_CAN1 TRUE
+
+define HAL_USE_I2C TRUE
+define STM32_I2C_USE_I2C1 TRUE
+
+define HAL_NO_ROMFS_SUPPORT
+
+define HAL_UART_MIN_TX_SIZE 256
+define HAL_UART_MIN_RX_SIZE 128
+
+define CH_DBG_ENABLE_STACK_CHECK TRUE
+
+define HAL_UART_STACK_SIZE 256
+define STORAGE_THD_WA_SIZE 512
+
+define HAL_NO_GCS
+define HAL_NO_LOGGING
+define HAL_NO_MONITOR_THREAD
+
+define HAL_MINIMIZE_FEATURES 0
+
+define HAL_BUILD_AP_PERIPH
+
+# only one I2C bus
+I2C_ORDER I2C1
+
+define HAL_COMPASS_DEFAULT HAL_COMPASS_RM3100_SPI
+
+define HAL_I2C_CLEAR_ON_TIMEOUT 0
+
+define HAL_DEVICE_THREAD_STACK 768
+
+define AP_PARAM_MAX_EMBEDDED_PARAM 0
+
+define HAL_PROBE_EXTERNAL_I2C_COMPASSES
+define HAL_I2C_INTERNAL_MASK 0
+
+# disable dual GPS and GPS blending to save flash space
+define GPS_MAX_RECEIVERS 1
+define GPS_MAX_INSTANCES 1