mirror of https://github.com/ArduPilot/ardupilot
hwdef: add hwdef for SDMODELH7V1
This commit is contained in:
Peter Barker
Peter Barker
parent
aa9feac747
commit
4ef85b14d0
|
|
@ -0,0 +1,183 @@
|
|||
## SDMODEL SDH7 V1
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
above image and some content courtesy of SDMODEL
|
||||
|
||||
## Specifications¶
|
||||
|
||||
Processor
|
||||
STM32H743 32-bit processor
|
||||
AT7456E OSD
|
||||
128 MByte flash for logging
|
||||
|
||||
Sensors
|
||||
BMI270 IMU (accel and gyro only, no compass)
|
||||
BMP280 barometer
|
||||
|
||||
Power
|
||||
2S - 8S Lipo input voltage with voltage monitoring
|
||||
9V, 1.5A BEC for powering Video Transmitter
|
||||
|
||||
Interfaces
|
||||
9x PWM outputs (9th pwm output is for NeoPixel LED string via the LED pad)
|
||||
1x RC input
|
||||
6x UARTs/serial for GPS and other peripherals
|
||||
1x I2C port for external compass
|
||||
USB-C port
|
||||
Switchable VTX power
|
||||
All UARTS support hardware inversion. SBUS, SmartPort, and other inverted protocols work on any UART without "uninvert hack"
|
||||
External current monitor input
|
||||
|
||||
## Pinout
|
||||
|
||||
PADS
|
||||
|
||||
========= ===================
|
||||
Pin Function
|
||||
========= ===================
|
||||
VTX 9v 9V for HD System or other VTX, by default ON/OFF is controlled by RELAY2. See Relay Switch Can be controlled by RELAY2
|
||||
SDA, SCL I2C connection (for peripherals)
|
||||
5V 5v output (1.5A max)
|
||||
3v3 3.3v output (0.25A max)
|
||||
Vi Video input from FPV camera
|
||||
Vo Video output to video transmitter
|
||||
CAM To camera OSD control
|
||||
G or GND Ground
|
||||
RSI Analog RSSI (0-3.3v) input from receiver
|
||||
R3, T3 UART3 RX and TX
|
||||
R4, T4 UART4 RX and TX
|
||||
R6, T6 UART6 RX and TX (UART6 RX is also located in the SH plug)
|
||||
LED WS2182 addressable LED signal wire
|
||||
Z- Piezo buzzer negative leg
|
||||
========= ===================
|
||||
|
||||
Connectors
|
||||
|
||||
ESC PORT1 (JST-SH-8P-1)
|
||||
========= ===================
|
||||
Pin Function
|
||||
========= ===================
|
||||
B+ Battery positive voltage (2S-8S)
|
||||
R7 UART7 RX
|
||||
GND Ground
|
||||
CURRENT CURRENT
|
||||
M1 Motor signal output 1
|
||||
M2 Motor signal output 2
|
||||
M3 Motor signal output 3
|
||||
M4 Motor signal output 4
|
||||
========= ===================
|
||||
|
||||
ESC PORT2 (JST-SH-8P-2)
|
||||
========= ===================
|
||||
Pin Function
|
||||
========= ===================
|
||||
B+ Battery positive voltage (2S-8S)
|
||||
R7 UART7 RX
|
||||
GND Ground
|
||||
CURRENT CURRENT
|
||||
M5 Motor signal output 5
|
||||
M6 Motor signal output 6
|
||||
M7 Motor signal output 7
|
||||
M8 Motor signal output 8
|
||||
========= ===================
|
||||
|
||||
DJI Connector JST-SH-6P-3
|
||||
========= ===================
|
||||
Pin Function
|
||||
========= ===================
|
||||
Vtx+ 9V for HD System or other VTX, by default ON/OFF is controlled by RELAY2. See Relay Switch
|
||||
G Ground
|
||||
T1 UART1 TX
|
||||
R1 UART1 RX
|
||||
G Ground
|
||||
R6 UART6 RX
|
||||
========= ===================
|
||||
|
||||
## UART Mapping¶
|
||||
|
||||
The UARTs are marked Rn and Tn in the above pinouts. The Rn pin is the receive pin for UARTn. The Tn pin is the transmit pin for UARTn.
|
||||
|
||||
- SERIAL0 -> USB
|
||||
- SERIAL1 -> UART1 (Telem1) DMA-enabled
|
||||
- SERIAL2 -> not available externally, internally connected to currently unsupported BT-LE module
|
||||
- SERIAL3 -> UART3 (SmartAudio VTX protocol by default)
|
||||
- SERIAL4 -> UART4 (GPS) DMA-enabled
|
||||
- SERIAL5 -> not available
|
||||
- SERIAL6 -> UART6 (Setup for serial RX Protocol SBUS by default) DMA-enabled
|
||||
- SERIAL7 -> UART7 (RX7 only available, normally used for ESC telemetry protocol by default)
|
||||
|
||||
The SERIAL7 port (UART7) is normally for ESC telemetry, and has an R7 pin on both of the ESC connectors.
|
||||
|
||||
Any UART may be re-tasked by changing its protocol parameter.
|
||||
|
||||
## Copter Default Frame Type¶
|
||||
|
||||
For Copter firmware the FRAME_TYPE is already defaulted to type "12" (BetaFlight X) allowing existing BetaFlight configurations with ESCs attached to have the correct motor ordering without changes to the FRAME_TYPE and FRAME_CLASS parameters or ESC wiring.
|
||||
|
||||
## RC Input¶
|
||||
|
||||
RC input is configured on the R6 (UART6_RX) pin. It supports all RC protocols except PPM. See Radio Control Systems for details for a specific RC system. SERIAL6_PROTOCOL is set to "23", by default, to enable this.
|
||||
|
||||
- SBUS/DSM/SRXL connects to the R6 pin.
|
||||
- FPort requires connection to T6 and SERIAL6_OPTIONS be set to "7".
|
||||
- CRSF also requires a T6 connection, in addition to R6, and automatically provides telemetry. Set SERIAL6_OPTIONS to "0".
|
||||
- SRXL2 requires a connecton to T6 and automatically provides telemetry. Set SERIAL6_OPTIONS to "4".
|
||||
|
||||
Any UART can be used for RC system connections in ArduPilot also, and is compatible with all protocols except PPM. See Radio Control Systems for details.
|
||||
FrSky Telemetry¶
|
||||
|
||||
FrSky Telemetry is supported using the Tx pin of any UART. You need to set the following parameters to enable support for FrSky S.PORT (example shows SERIAL2).
|
||||
|
||||
- SERIAL2_PROTOCOL 10
|
||||
- SERIAL2_OPTIONS 7
|
||||
|
||||
## OSD Support¶
|
||||
|
||||
The SDH7V1 supports OSD using OSD_TYPE 1 (MAX7456 driver). The defaults are also setup to allow DJI Goggle OSD support on UART1.
|
||||
PWM Output¶
|
||||
|
||||
The KakuteH7 supports up to 8 PWM outputs. Outputs are available via two JST-SH connectors. All 8 outputs support DShot and bi-directional DShot, as well as all PWM types.
|
||||
|
||||
The PWM is in 3 groups:
|
||||
|
||||
- PWM 1, 2 in group1
|
||||
- PWM 3, 4 in group2
|
||||
- PWM 5, 6 in group3
|
||||
- PWM 7, 8 in group4
|
||||
- PWM 9 (LED) in group5
|
||||
|
||||
Channels within the same group need to use the same output rate, whether PWM or Dshot. If any channel in a group uses DShot then all channels in the group need to use DShot.
|
||||
|
||||
## LED Output¶
|
||||
|
||||
The LED output is configured by default to support NeoPixel LED strings.
|
||||
Battery Monitoring¶
|
||||
|
||||
The board has a built-in voltage sensor via the B+ pin, but no internal current sensor. An external current sensor can be connected to the CUR pin.
|
||||
|
||||
The correct battery setting parameters are:
|
||||
|
||||
- BATT_MONITOR 4
|
||||
- BATT_VOLT_PIN 10
|
||||
- BATT_CURR_PIN 11
|
||||
- BATT_VOLT_MULT 10.1
|
||||
- BATT_AMP_PERVLT varies depending on external current sensor
|
||||
|
||||
## Compass¶
|
||||
|
||||
The SDMODEL SDH7V1 does not have a built-in compass, however you can attach an external compass using I2C on the SDA and SCL pads.
|
||||
Firmware¶
|
||||
|
||||
## Loading Firmware¶
|
||||
|
||||
Initial firmware load can be done with DFU by plugging in USB with the bootloader button pressed. Then you should load the "with_bl.hex" firmware, using your favourite DFU loading tool.
|
||||
|
||||
Once the initial firmware is loaded you can update the firmware using any ArduPilot ground station software. Later updates should be done with the *.apj firmware files.
|
||||
|
||||
## Connection Diagram
|
||||
|
||||
|
||||
|
||||
Binary file not shown.
|
After Width: | Height: | Size: 1.1 MiB |
Binary file not shown.
|
After Width: | Height: | Size: 130 KiB |
Binary file not shown.
|
After Width: | Height: | Size: 1.2 MiB |
|
|
@ -0,0 +1 @@
|
|||
@include ../KakuteH7v2/defaults.parm
|
||||
|
|
@ -0,0 +1,4 @@
|
|||
include ../KakuteH7v2/hwdef-bl.dat
|
||||
|
||||
# board ID for firmware load
|
||||
APJ_BOARD_ID 1111
|
||||
|
|
@ -0,0 +1,4 @@
|
|||
include ../KakuteH7v2/hwdef.dat
|
||||
|
||||
# board ID for firmware load
|
||||
APJ_BOARD_ID 1111
|
||||
Loading…
Reference in New Issue