Mirror
/
ardupilot
mirror of https://github.com/ArduPilot/ardupilot
5
0
Fork 0
Code Issues Packages Projects Releases Wiki Activity

hwdef: Back Port updated hwdefs for mRo boards

This commit is contained in:
pkocmoud 2021-02-16 16:29:46 -06:00 committed by Andrew Tridgell
parent 4ed19f5f0b
commit 46001d6915
14 changed files with 1174 additions and 93 deletions
Show Stats Download Patch File Download Diff File Expand all files Collapse all files

64
libraries/AP_HAL_ChibiOS/hwdef/mRoControlZeroClassic/hwdef-bl.dat Normal file
View File

@ -0,0 +1,64 @@
###########################################################################################################################################################
# hw definition file for processing by chibios_hwdef.py
# STM32H743ZIT6
# mRo Control Zero Classic flight controller
# 12x PWM / IO - DMA capable and switchable 3.3v (default) / 5v Logic
# A Dual CAN based flight controller
# 3x IMUs (BMI088 6DOF, ICM20602 6DOF, ICM20948 9DOF)
# Baro, FRAM (256kb), SDCARD Socket, JTAG
# 5x UARTs (2x with hardware flow control), 2x CAN, 1x SPI, 2x I2C
# Onboard 3 color LED and buzzer
# Identical case and connector layout to the original 3DR / mRo Pixhawk
# M10048B - Initial Release
###########################################################################################################################################################
# MCU class and specific type
MCU STM32H7xx STM32H743xx
# USB setup
USB_STRING_MANUFACTURER "mRo"
# crystal frequency
OSCILLATOR_HZ 24000000
# board ID for firmware load
APJ_BOARD_ID 1022
FLASH_SIZE_KB 2048
# bootloader is installed at zero offset
FLASH_RESERVE_START_KB 0
# the location where the bootloader will put the firmware
FLASH_BOOTLOADER_LOAD_KB 128
PB4 LED_BOOTLOADER OUTPUT
# define all 3 to make LED output White.
PB1 LED_ACTIVITY OUTPUT
PB3 LED_ACTIVITY2 OUTPUT
# PB11 LED_ACTIVITY3 OUTPUT
define HAL_LED_ON 0
# order of UARTs (and USB)
SERIAL_ORDER OTG1
PA11 OTG_FS_DM OTG1
PA12 OTG_FS_DP OTG1
PA13 JTMS-SWDIO SWD
PA14 JTCK-SWCLK SWD
define HAL_USE_EMPTY_STORAGE 1
define HAL_STORAGE_SIZE 16384
# Add CS pins to ensure they are high in bootloader
PD7 BARO_CS CS
PD10 FRAM_CS CS SPEED_VERYLOW
PE15 ICM_20948_CS CS
PF0 BMI088_ACCEL_CS CS
PF10 BMI088_GYRO_CS CS
PG3 ICM_20602_CS CS
PG9 EXT_SPI_CS CS
#PG10 EXT_SPI_CS CS

299
libraries/AP_HAL_ChibiOS/hwdef/mRoControlZeroClassic/hwdef.dat Normal file
View File

@ -0,0 +1,299 @@
###########################################################################################################################################################
# hw definition file for processing by chibios_hwdef.py
# STM32H743ZIT6
# mRo Control Zero Classic flight controller
# 12x PWM / IO - DMA capable and switchable 3.3v (default) / 5v Logic
# A Dual CAN based flight controller
# 3x IMUs (BMI088 6DOF, ICM20602 6DOF, ICM20948 9DOF)
# Baro, FRAM (256kb), SDCARD Socket, JTAG
# 5x UARTs (2x with hardware flow control), 2x CAN, 1x SPI, 2x I2C
# Onboard 3 color LED and buzzer
# Identical case and connector layout to the original 3DR / mRo Pixhawk
# M10048B - Initial Release
###########################################################################################################################################################
# MCU class and specific type
MCU STM32H7xx STM32H743xx
# USB setup
USB_STRING_MANUFACTURER "mRo"
# board ID for firmware load
APJ_BOARD_ID 1022
# crystal frequency
OSCILLATOR_HZ 24000000
FLASH_SIZE_KB 2048
# with 2M flash we can afford to optimize for speed
env OPTIMIZE -O2
# start on 2th sector (1st sector for bootloader)
FLASH_RESERVE_START_KB 128
# use FRAM for storage
define HAL_STORAGE_SIZE 16384
# Enable RAMTROM parameter storage.
define HAL_WITH_RAMTRON 1
# RC Input set for Interrupt not DMA
PC7 TIM3_CH2 TIM3 RCININT FLOAT LOW
# also USART6_RX for serial RC
# Control of Spektrum power pin
PE4 SPEKTRUM_PWR OUTPUT LOW GPIO(70)
define HAL_GPIO_SPEKTRUM_PWR 70
# Spektrum Power is Active Low
define HAL_SPEKTRUM_PWR_ENABLED 0
# Spektrum RC Input pin, used as GPIO for bind for Satellite Receivers
PG0 SPEKTRUM_RC INPUT PULLUP GPIO(71)
define HAL_GPIO_SPEKTRUM_RC 71
# Order of I2C buses
I2C_ORDER I2C1 I2C4
# Now the first I2C bus. The pin speeds are automatically setup
# correctly, but can be overridden here if needed.
PB8 I2C1_SCL I2C1
PB9 I2C1_SDA I2C1
# Now the first I2C bus. The pin speeds are automatically setup
# correctly, but can be overridden here if needed.
PF14 I2C4_SCL I2C4
PF15 I2C4_SDA I2C4
# this board has no internal I2C busses
define HAL_I2C_INTERNAL_MASK 0
# order of UARTs (and USB) and suggested usage
# USART2 Telem 1 (Flow Control)
# USART3 Telem 2 (Flow Control)
# UART4 GPS with I2C1
# UART7 GPS2 with I2C4
# UART8 FRSKY Telem
# USART1 Additional UART
# UART6 RC input (Only RX pin is connected)
SERIAL_ORDER OTG1 USART2 USART3 UART4 UART7 UART8 USART1 OTG2
# default the 2nd interface to MAVLink2 until MissionPlanner updates drivers
define HAL_OTG2_PROTOCOL SerialProtocol_MAVLink2
# Another USART, this one for telem1. This one has RTS and CTS lines.
# USART2 telem1
PD3 USART2_CTS USART2
PD4 USART2_RTS USART2
PD5 USART2_TX USART2
PD6 USART2_RX USART2
# The telem2 USART, this one for telem2. This one has RTS and CTS lines.
# USART3 telem2
PD8 USART3_TX USART3
PD9 USART3_RX USART3
PD11 USART3_CTS USART3
PD12 USART3_RTS USART3
# UART4 GPS
PA0 UART4_TX UART4
PA1 UART4_RX UART4
# UART7 GPS2
PE7 UART7_RX UART7
PE8 UART7_TX UART7
# UART8 FrSky Telemetry
PE0 UART8_RX UART8
PE1 UART8_TX UART8
# USART1 Spektrum RX
PB6 USART1_TX USART1
PB7 USART1_RX USART1
# This is the pin to enable the 3.3v sensors rail. It can be used to power
# cycle sensors to recover them in case there are problems with power on
# timing affecting sensor stability. We pull it high by default.
PE3 VDD_3V3_SENSORS_EN OUTPUT HIGH GPIO(72)
# This is the pin to enable the 1.8v sensors rail. It can be used to power
# cycle sensors to recover them in case there are problems with power on
# timing affecting sensor stability. We pull it high by default.
PC13 VDD_1V8_SENSORS_EN OUTPUT HIGH GPIO(73)
# This defines more ADC inputs.
PB0 AUX_ADC1 ADC1 SCALE(1)
PB1 AUX_ADC2 ADC1 SCALE(1)
# And the analog input for airspeed (rarely used these days).
PC5 PRESSURE_SENS ADC1 SCALE(2)
# RSSI Analog Input
PC0 RSSI_IN ADC1
# Safety Switch Input
PA10 SAFETY_IN INPUT
PE6 LED_SAFETY OUTPUT
PC4 BATT_VOLTAGE_SENS ADC1 SCALE(1)
PA3 BATT_CURRENT_SENS ADC1 SCALE(1)
# Now the VDD sense pin. This is used to sense primary board voltage.
PA4 VDD_5V_SENS ADC1 SCALE(2)
# Now setup the default battery pins driver analog pins and default
# scaling for the power brick.
define HAL_BATT_VOLT_PIN 4
define HAL_BATT_CURR_PIN 15
define HAL_BATT_VOLT_SCALE 10.1
define HAL_BATT_CURR_SCALE 17.0
#SPI1 ICM_20602 / ICM_20948
PA5 SPI1_SCK SPI1
PA6 SPI1_MISO SPI1
PA7 SPI1_MOSI SPI1
#SPI2 FRAM / DPS310
PB10 SPI2_SCK SPI2
PB14 SPI2_MISO SPI2
PB15 SPI2_MOSI SPI2
#SPI5 BMI088
PF7 SPI5_SCK SPI5
PF8 SPI5_MISO SPI5
PF9 SPI5_MOSI SPI5
#SPI6 EXTERNAL
PG13 SPI6_SCK SPI6
PG12 SPI6_MISO SPI6
PG14 SPI6_MOSI SPI6
# This is the pin that senses USB being connected. It is an input pin
# setup as OPENDRAIN.
PA9 VBUS INPUT OPENDRAIN
# Pins that USB is connected to.
PA11 OTG_FS_DM OTG1
PA12 OTG_FS_DP OTG1
# These are the pins for SWD debugging with a STlinkv2 or black-magic probe.
PA13 JTMS-SWDIO SWD
PA14 JTCK-SWCLK SWD
# PWM output for buzzer
# PF6 TIM16_CH1 TIM16 GPIO(74) ALARM
# Now setup the pins for the microSD card, if available.
PC8 SDMMC1_D0 SDMMC1
PC9 SDMMC1_D1 SDMMC1
PC10 SDMMC1_D2 SDMMC1
PC11 SDMMC1_D3 SDMMC1
PC12 SDMMC1_CK SDMMC1
PD2 SDMMC1_CMD SDMMC1
# More CS pins for more sensors. The labels for all CS pins need to
# match the SPI device table later in this file.
PD7 BARO_CS CS
PD10 FRAM_CS CS SPEED_VERYLOW
PE15 ICM_20948_CS CS
PF0 BMI088_ACCEL_CS CS
PF10 BMI088_GYRO_CS CS
PG3 ICM_20602_CS CS
PG9 EXT_SPI_CS CS
PG10 EXT2_SPI_CS CS
# the first CAN bus
PD0 CAN1_RX CAN1
PD1 CAN1_TX CAN1
PF11 GPIO_CAN1_SILENT OUTPUT PUSHPULL SPEED_LOW LOW GPIO(75)
# the second CAN bus
PB12 CAN2_RX CAN2
PB13 CAN2_TX CAN2
PF12 GPIO_CAN2_SILENT OUTPUT PUSHPULL SPEED_LOW LOW GPIO(76)
# Now we start defining some PWM pins. We also map these pins to GPIO
# values, so users can set BRD_PWM_COUNT to choose how many of the PWM
# outputs on the primary MCU are setup as PWM and how many as
# GPIOs. To match HAL_PX4 we number the GPIOs for the PWM outputs
# starting at 50.
PE14 TIM1_CH4 TIM1 PWM(1) GPIO(50)
PE13 TIM1_CH3 TIM1 PWM(2) GPIO(51)
PE11 TIM1_CH2 TIM1 PWM(3) GPIO(52)
PE9 TIM1_CH1 TIM1 PWM(4) GPIO(53)
PD13 TIM4_CH2 TIM4 PWM(5) GPIO(54)
PD14 TIM4_CH3 TIM4 PWM(6) GPIO(55)
PA2 TIM2_CH3 TIM2 PWM(7) GPIO(56)
PA15 TIM2_CH1 TIM2 PWM(8) GPIO(57)
PB11 TIM2_CH4 TIM2 PWM(9) GPIO(58)
PE5 TIM15_CH1 TIM15 PWM(10) GPIO(59)
PC6 TIM8_CH1 TIM8 PWM(11) GPIO(60)
PD15 TIM4_CH4 TIM4 PWM(12) GPIO(61)
define BOARD_PWM_COUNT_DEFAULT 12
# This is the invensense data-ready pin. We don't use it in the
# default driver.
PG2 MPU_DRDY INPUT
# Pin for PWM Voltage Selection, 0 means 3.3v, 1 means 5v
PG6 PWM_VOLT_SEL OUTPUT LOW GPIO(77)
define HAL_GPIO_PWM_VOLT_PIN 77
define HAL_GPIO_PWM_VOLT_3v3 0
# Power flag pins: these tell the MCU the status of the various power
# supplies that are available. The pin names need to exactly match the
# names used in AnalogIn.cpp.
PC1 VDD_BRICK_nVALID INPUT PULLUP
SPIDEV bmi088_g SPI5 DEVID1 BMI088_GYRO_CS MODE3 10*MHZ 10*MHZ
SPIDEV bmi088_a SPI5 DEVID2 BMI088_ACCEL_CS MODE3 10*MHZ 10*MHZ
SPIDEV icm20608 SPI1 DEVID2 ICM_20602_CS MODE3 2*MHZ 8*MHZ
SPIDEV icm20948 SPI1 DEVID1 ICM_20948_CS MODE3 2*MHZ 4*MHZ
SPIDEV dps280 SPI2 DEVID3 BARO_CS MODE3 5*MHZ 5*MHZ
SPIDEV ramtron SPI2 DEVID10 FRAM_CS MODE3 8*MHZ 8*MHZ
# Now some defines for logging and terrain data files.
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"
# allow to have have a dedicated safety switch pin
define HAL_HAVE_SAFETY_SWITCH 1
# Enable FAT filesystem support (needs a microSD defined via SDMMC).
define HAL_OS_FATFS_IO 1
# Control Zero has a TriColor LED, Red, Green, Blue
define HAL_HAVE_PIXRACER_LED
define HAL_GPIO_LED_ON 0
define HAL_GPIO_LED_OFF 1
# LED setup for PixracerLED driver
PB4 LED_R OUTPUT HIGH GPIO(0)
PB5 LED_G OUTPUT HIGH GPIO(1)
PB3 LED_B OUTPUT HIGH GPIO(2)
define HAL_GPIO_A_LED_PIN 0
define HAL_GPIO_B_LED_PIN 1
define HAL_GPIO_C_LED_PIN 2
# 3 IMUs
IMU BMI088 SPI:bmi088_a SPI:bmi088_g ROTATION_NONE
IMU Invensense SPI:icm20608 ROTATION_ROLL_180_YAW_90
IMU Invensensev2 SPI:icm20948 ROTATION_ROLL_180_YAW_90
# 1 baro
BARO DPS280 SPI:dps280
# 1 compass
COMPASS AK09916:probe_ICM20948 0 ROTATION_ROLL_180
define HAL_PROBE_EXTERNAL_I2C_COMPASSES

7
libraries/AP_HAL_ChibiOS/hwdef/mRoControlZeroF7/defaults.parm Normal file
View File

@ -0,0 +1,7 @@
#Default Parameters for the mRo Control Zero F7
CAN_P1_DRIVER 1
CAN_SLCAN_CPORT 1
SERIAL6_PROTOCOL 22

24
libraries/AP_HAL_ChibiOS/hwdef/mRoControlZeroF7/hwdef-bl.dat
View File

@ -1,5 +1,18 @@
# hw definition file for processing by chibios_hwdef.py
# for F777 bootloader
###########################################################################################################################################################
# mRo Control Zero F7 Flight Controller
# STM32F777IIK6
# 8x PWM / IO - DMA capable, buffered and level shiftable - 3.3v (default) / 5v Logic
# Front and Rear Connectors: 30pin Molex PicoClasp
# 3x IMUs (BMI088 6DOF, ICM20602 6DOF, ICM20948 9DOF)
# DPS310 Baro, FRAM (256Bb), SDCARD Socket, TC2030 JTAG
# 5x UARTs (2x with hardware flow control), 2x CAN, 1x SPI, 1x I2C
# Onboard 3 color LED and buzzer
# Uncased Weight and Dimensions:
# Weight: 5.3g (.19oz)
# Width: 20mm (.79in)
# Length: 32mm (1.26in)
# M10058 - Initial Release
###########################################################################################################################################################
# MCU class and specific type
MCU STM32F7xx STM32F777xx
@ -30,13 +43,8 @@ PB3 LED_ACTIVITY2 OUTPUT
define HAL_LED_ON 0
# order of UARTs (and USB)
SERIAL_ORDER OTG1 UART7
# UART7 maps to uartF in the HAL (serial5 in SERIALn_ parameters).
PE7 UART7_RX UART7
PE8 UART7_TX UART7
SERIAL_ORDER OTG1
PA11 OTG_FS_DM OTG1
PA12 OTG_FS_DP OTG1

109
libraries/AP_HAL_ChibiOS/hwdef/mRoControlZeroF7/hwdef.dat
View File

@ -1,8 +1,29 @@
# hw definition file for processing by chibios_hwdef.py
###########################################################################################################################################################
# mRo Control Zero F7 Flight Controller
# STM32F777IIK6
# 8x PWM / IO - DMA capable, buffered and level shiftable - 3.3v (default) / 5v Logic
# Front and Rear Connectors: 30pin Molex PicoClasp
# 3x IMUs (BMI088 6DOF, ICM20602 6DOF, ICM20948 9DOF)
# DPS310 Baro, FRAM (256Bb), SDCARD Socket, TC2030 JTAG
# 5x UARTs (2x with hardware flow control), 2x CAN, 1x SPI, 1x I2C
# Onboard 3 color LED and buzzer
# Uncased Weight and Dimensions:
# Weight: 5.3g (.19oz)
# Width: 20mm (.79in)
# Length: 32mm (1.26in)
# M10058 - Initial Release
###########################################################################################################################################################
# MCU class and specific type
MCU STM32F7xx STM32F777xx
# ChibiOS system timer
# this is the STM32 timer that ChibiOS will use for the low level
# driver. This must be a 32 bit timer, so Timers 2 or 5 on the STM32F777.
# See hal_st_lld.c in ChibiOS for details
STM32_ST_USE_TIMER 5
# board ID for firmware load
APJ_BOARD_ID 141
@ -17,23 +38,18 @@ env OPTIMIZE -O2
# start on 4th sector (1st sector for bootloader, 2 for extra storage)
FLASH_RESERVE_START_KB 96
# use FRAM for storage
define HAL_STORAGE_SIZE 16384
define HAL_WITH_RAMTRON 1
# fallback storage in case FRAM is not populated
define STORAGE_FLASH_PAGE 1
# this is the STM32 timer that ChibiOS will use for the low level
# driver. This must be a 32 bit timer, so Timers 2 or 5 on the STM32F777.
# See hal_st_lld.c in ChibiOS for details
# ChibiOS system timer
STM32_ST_USE_TIMER 5
define HAL_STORAGE_SIZE 32768
# USB setup
USB_STRING_MANUFACTURER "mRo"
# RC Input set for Interrupt not DMA
PC7 TIM3_CH2 TIM3 RCININT FLOAT LOW # also USART6_RX for serial RC
# RC Input set for Interrupt not DMA also USART6_RX for serial RC
PC7 TIM3_CH2 TIM3 RCININT FLOAT LOW
# Control of Spektrum power pin
PE4 SPEKTRUM_PWR OUTPUT LOW GPIO(70)
@ -52,21 +68,15 @@ I2C_ORDER I2C1
# this board only has a single I2C bus so make it external
define HAL_I2C_INTERNAL_MASK 0
# OEM Only
# I2C_ORDER I2C1, I2C2, I2C3
# order of UARTs (and USB)
# UART4 GPS
# USART2 FC
# USART3 FC
# USART2 Telem 1 (Flow Control)
# USART3 Telem 2 (Flow Control)
# UART8 FRSKY Telem
# USART6 FC
# UART7 DEBUG
# USART6 RC input (Only RX pin is connected)
# UART7 Additional UART
SERIAL_ORDER OTG1 USART2 USART3 UART4 UART8 USART6 UART7 OTG2
# default the 2nd interface to MAVLink2 until MissionPlanner updates drivers
define HAL_OTG2_PROTOCOL SerialProtocol_MAVLink2
SERIAL_ORDER OTG1 USART2 USART3 UART4 UART8 UART7 OTG2
# Another USART, this one for telem1. This one has RTS and CTS lines.
# USART2 telem1
@ -86,11 +96,7 @@ PD12 USART3_RTS USART3
PA0 UART4_TX UART4
PA1 UART4_RX UART4 NODMA
# USART6 Spare or can be configured as SPI6
PG14 USART6_TX USART6 NODMA
PG9 USART6_RX USART6 NODMA
# UART7 maps to uartF in the HAL (serial5 in SERIALn_ parameters). Debug Console
# UART7 Spare or Debug Console
PE7 UART7_RX UART7 NODMA
PE8 UART7_TX UART7 NODMA
@ -125,12 +131,20 @@ PF7 SPI5_SCK SPI5
PF8 SPI5_MISO SPI5
PF9 SPI5_MOSI SPI5
# GPIOs
# This defines general purpose outputs, mapped to GPIO
# numbers 1 thru 4 for users.
PG9 EXTERN_GPIO1 GPIO(1)
PG13 EXTERN_GPIO2 GPIO(2)
PG12 EXTERN_GPIO3 GPIO(3)
PG14 EXTERN_GPIO4 GPIO(4)
# This is the pin that senses USB being connected. It is an input pin
# setup as OPENDRAIN.
PA9 VBUS INPUT OPENDRAIN
# This input pin is used to detect that power is valid on USB.
PC0 VBUS_VALID INPUT
PC0 VBUS_VALID INPUT PULLDOWN
# Now we define the pins that USB is connected on.
PA11 OTG_FS_DM OTG1
@ -148,14 +162,6 @@ PA15 TIM2_CH1 TIM2 GPIO(77) ALARM
PB8 I2C1_SCL I2C1
PB9 I2C1_SDA I2C1
# the 2nd I2C bus, OEM Only
# PB10 I2C2_SCL I2C2
# PB11 I2C2_SDA I2C2
# the 3nd I2C bus, OEM Only
# PB6 I2C4_SCL I2C4
# PB7 I2C4_SDA I2C4
# Now setup the pins for the microSD card, if available.
PC8 SDMMC_D0 SDMMC1
PC9 SDMMC_D1 SDMMC1
@ -168,8 +174,6 @@ PD2 SDMMC_CMD SDMMC1
# match the SPI device table later in this file.
PC2 ICM_20602_CS CS
PD7 BARO_CS CS
# The CS pin for FRAM (ramtron). This one is marked as using
# SPEED_VERYLOW, which matches the HAL_PX4 setup.
PD10 FRAM_CS CS SPEED_VERYLOW NODMA
PE15 ICM_20948_CS CS
PF10 BMI088_GYRO_CS CS
@ -181,10 +185,6 @@ PD1 CAN1_TX CAN1
PF5 GPIO_CAN1_SILENT OUTPUT PUSHPULL SPEED_LOW LOW GPIO(72)
# This defines the pins for the 2nd CAN interface, OEM Only.
# PB6 CAN2_TX CAN2
# PB4 CAN2_RX CAN2
# Now we start defining some PWM pins. We also map these pins to GPIO
# values, so users can set BRD_PWM_COUNT to choose how many of the PWM
# outputs on the primary MCU are setup as PWM and how many as
@ -213,14 +213,14 @@ PE3 VDD_3V3_SENSORS_EN OUTPUT HIGH
# Power flag pins: these tell the MCU the status of the various power
# supplies that are available. The pin names need to exactly match the
# names used in AnalogIn.cpp.
PB5 VDD_BRICK_VALID INPUT PULLUP
PB5 VDD_BRICK_nVALID INPUT PULLUP
SPIDEV dps310 SPI2 DEVID3 BARO_CS MODE3 5*MHZ 5*MHZ
SPIDEV dps280 SPI2 DEVID3 BARO_CS MODE3 5*MHZ 5*MHZ
SPIDEV ramtron SPI2 DEVID10 FRAM_CS MODE3 8*MHZ 8*MHZ
SPIDEV bmi088_g SPI5 DEVID1 BMI088_GYRO_CS MODE3 5*MHZ 5*MHZ
SPIDEV bmi088_a SPI5 DEVID2 BMI088_ACCEL_CS MODE3 5*MHZ 5*MHZ
SPIDEV icm20608 SPI1 DEVID2 ICM_20602_CS MODE3 2*MHZ 4*MHZ
SPIDEV icm20948 SPI1 DEVID1 ICM_20948_CS MODE3 2*MHZ 4*MHZ
SPIDEV icm20608 SPI1 DEVID2 ICM_20602_CS MODE3 2*MHZ 8*MHZ
SPIDEV bmi088_g SPI5 DEVID1 BMI088_GYRO_CS MODE3 10*MHZ 10*MHZ
SPIDEV bmi088_a SPI5 DEVID2 BMI088_ACCEL_CS MODE3 10*MHZ 10*MHZ
# Now some defines for logging and terrain data files.
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
@ -229,9 +229,6 @@ define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"
# allow to have have a dedicated safety switch pin
define HAL_HAVE_SAFETY_SWITCH 1
# Enable RAMTROM parameter storage.
define HAL_WITH_RAMTRON 1
# Enable FAT filesystem support (needs a microSD defined via SDMMC).
define HAL_OS_FATFS_IO 1
@ -258,16 +255,16 @@ define HAL_GPIO_B_LED_PIN 1
define HAL_GPIO_C_LED_PIN 2
DMA_PRIORITY SDMMC*
#DMA_NOSHARE SPI1* *
#DMA_NOSHARE SPI5* *
# 3 IMUs
IMU Invensensev2 SPI:icm20948 ROTATION_ROLL_180_YAW_90
IMU Invensense SPI:icm20608 ROTATION_ROLL_180_YAW_90
IMU BMI088 SPI:bmi088_a SPI:bmi088_g ROTATION_NONE
IMU Invensense SPI:icm20608 ROTATION_ROLL_180_YAW_90
IMU Invensensev2 SPI:icm20948 ROTATION_ROLL_180_YAW_90
define HAL_DEFAULT_INS_FAST_SAMPLE 7
# 1 baro
BARO DPS280 SPI:dps310
BARO DPS280 SPI:dps280
# 1 compass
COMPASS AK09916:probe_ICM20948 0 ROTATION_ROLL_180

7
libraries/AP_HAL_ChibiOS/hwdef/mRoControlZeroH7/defaults.parm Normal file
View File

@ -0,0 +1,7 @@
#Default Parameters for the mRo Control Zero H7
CAN_P1_DRIVER 1
CAN_SLCAN_CPORT 1
SERIAL6_PROTOCOL 22

65
libraries/AP_HAL_ChibiOS/hwdef/mRoControlZeroH7/hwdef-bl.dat Normal file
View File

@ -0,0 +1,65 @@
###########################################################################################################################################################
# mRo Control Zero H7 Flight Controller
# STM32H743IIK6
# 8x PWM / IO - DMA capable, buffered and level shiftable - 3.3v (default) / 5v Logic
# Front and Rear Connectors: 30pin Molex PicoClasp
# 3x IMUs (BMI088 6DOF, ICM20602 6DOF, ICM20948 9DOF)
# DPS310 Baro, FRAM (256Bb), SDCARD Socket, TC2030 JTAG
# 5x UARTs (2x with hardware flow control), 1x CAN, 1x SPI, 1x I2C
# Onboard 3 color LED and buzzer
# Uncased Weight and Dimensions:
# Weight: 5.3g (.19oz)
# Width: 20mm (.79in)
# Length: 32mm (1.26in)
# M10058 - Initial Release
###########################################################################################################################################################
# MCU class and specific type
MCU STM32H7xx STM32H743xx
# USB setup
USB_STRING_MANUFACTURER "mRo"
# crystal frequency
OSCILLATOR_HZ 24000000
# board ID for firmware load
APJ_BOARD_ID 1023
FLASH_SIZE_KB 2048
# bootloader is installed at zero offset
FLASH_RESERVE_START_KB 0
# the location where the bootloader will put the firmware
FLASH_BOOTLOADER_LOAD_KB 128
PB11 LED_BOOTLOADER OUTPUT
# define all 3 to make LED output White.
PB1 LED_ACTIVITY OUTPUT
PB3 LED_ACTIVITY2 OUTPUT
# PB11 LED_ACTIVITY3 OUTPUT
define HAL_LED_ON 0
# order of UARTs (and USB)
SERIAL_ORDER OTG1
PA11 OTG_FS_DM OTG1
PA12 OTG_FS_DP OTG1
PA13 JTMS-SWDIO SWD
PA14 JTCK-SWCLK SWD
define HAL_USE_EMPTY_STORAGE 1
define HAL_STORAGE_SIZE 16384
# Add CS pins to ensure they are high in bootloader
PC2 ICM_20602_CS CS
PD7 BARO_CS CS
PD10 FRAM_CS CS SPEED_VERYLOW NODMA
PE15 ICM_20948_CS CS
PF6 BMI088_ACCEL_CS CS
PF10 BMI088_GYRO_CS CS
PG9 EXTERNAL CS

265
libraries/AP_HAL_ChibiOS/hwdef/mRoControlZeroH7/hwdef.dat Normal file
View File

@ -0,0 +1,265 @@
###########################################################################################################################################################
# mRo Control Zero H7 Flight Controller
# STM32H743IIK6
# 8x PWM / IO - DMA capable, buffered and level shiftable - 3.3v (default) / 5v Logic
# Front and Rear Connectors: 30pin Molex PicoClasp
# 3x IMUs (BMI088 6DOF, ICM20602 6DOF, ICM20948 9DOF)
# DPS310 Baro, FRAM (256Bb), SDCARD Socket, TC2030 JTAG
# 5x UARTs (2x with hardware flow control), 1x CAN, 1x SPI, 1x I2C
# Onboard 3 color LED and buzzer
# Uncased Weight and Dimensions:
# Weight: 5.3g (.19oz)
# Width: 20mm (.79in)
# Length: 32mm (1.26in)
# M10058 - Initial Release
###########################################################################################################################################################
# MCU class and specific type
MCU STM32H7xx STM32H743xx
# board ID for firmware load
APJ_BOARD_ID 1023
# crystal frequency
OSCILLATOR_HZ 24000000
FLASH_SIZE_KB 2048
# with 2M flash we can afford to optimize for speed
env OPTIMIZE -O2
# start on 2th sector (1st sector for bootloader)
FLASH_RESERVE_START_KB 128
define HAL_STORAGE_SIZE 32768
# USB setup
USB_STRING_MANUFACTURER "mRo"
# RC Input set for Interrupt not DMA
PC7 TIM3_CH2 TIM3 RCININT FLOAT LOW
# GPIO(70) # also USART6_RX for serial RC
# Control of Spektrum power pin
PE4 SPEKTRUM_PWR OUTPUT LOW GPIO(70)
define HAL_GPIO_SPEKTRUM_PWR 70
# Spektrum Power is Active High
define HAL_SPEKTRUM_PWR_ENABLED 0
# Spektrum RC Input pin, used as GPIO for bind for Satellite Receivers
PB0 SPEKTRUM_RC INPUT PULLUP GPIO(71)
define HAL_GPIO_SPEKTRUM_RC 71
# Order of I2C buses
I2C_ORDER I2C1
# this board has no internal I2C buses so them all external
define HAL_I2C_INTERNAL_MASK 0
# order of UARTs and suggested uses
# USART2 TELEM1
# USART3 TELEM2
# UART4 GPS
# UART8 FRSKY Telem
# UART7 DEBUG
# USART6 RC input (Only RX pin is connected)
# OTG1 and OTG2 are USB devices (1x physical USB connection enumerated as 2x logical ports)
SERIAL_ORDER OTG1 USART2 USART3 UART4 UART8 UART7 OTG2
# default the 2nd interface to MAVLink2 until MissionPlanner updates drivers
define HAL_OTG2_PROTOCOL SerialProtocol_MAVLink2
# Another USART, this one for telem1. This one has RTS and CTS lines.
# USART2 telem1
PD5 USART2_TX USART2
PD6 USART2_RX USART2
PD3 USART2_CTS USART2
PD4 USART2_RTS USART2
# The telem2 USART, this one for telem2. This one has RTS and CTS lines.
# USART3 telem2
PD8 USART3_TX USART3
PD9 USART3_RX USART3
PD11 USART3_CTS USART3
PD12 USART3_RTS USART3
# UART4 GPS
PA0 UART4_TX UART4
PA1 UART4_RX UART4
# UART7
PE8 UART7_TX UART7
PE7 UART7_RX UART7
# UART8 FrSky Telemetry (Single wire serial connects to the TX pin only)
PE1 UART8_TX UART8
PE0 UART8_RX UART8
# RSSI Analog Input
PC1 RSSI_IN ADC1
# Safety Switch Input
PC4 SAFETY_IN INPUT PULLDOWN
define HAL_HAVE_SAFETY_SWITCH 1
# Battery Analog Sense Pins
PA2 BATT_VOLTAGE_SENS ADC1 SCALE(1)
PA3 BATT_CURRENT_SENS ADC1 SCALE(1)
# Now the VDD sense pin. This is used to sense primary board voltage.
PA4 VDD_5V_SENS ADC1 SCALE(2)
# Now setup the default battery pins driver analog pins and default
# scaling for the power brick.
define HAL_BATT_VOLT_PIN 14
define HAL_BATT_CURR_PIN 15
define HAL_BATT_VOLT_SCALE 10.1
define HAL_BATT_CURR_SCALE 17.0
#SPI1 ICM_20602 / ICM_20948
PA5 SPI1_SCK SPI1
PA6 SPI1_MISO SPI1
PA7 SPI1_MOSI SPI1
#SPI2 FRAM / DPS310
PB10 SPI2_SCK SPI2
PB14 SPI2_MISO SPI2
PB15 SPI2_MOSI SPI2
#SPI5 BMI088
PF7 SPI5_SCK SPI5
PF8 SPI5_MISO SPI5
PF9 SPI5_MOSI SPI5
#SPI6 External
PG13 SPI6_SCK SPI6
PG12 SPI6_MISO SPI6
PG14 SPI6_MOSI SPI6
# This is the pin that senses USB being connected. It is an input pin
# setup as OPENDRAIN.
PA9 VBUS INPUT OPENDRAIN
# This input pin is used to detect that power is valid on USB.
PC0 VBUS_VALID INPUT PULLDOWN
# Now we define the pins that USB is connected on.
PA11 OTG_FS_DM OTG1
PA12 OTG_FS_DP OTG1
# These are the pins for SWD debugging with a STlinkv2 or black-magic probe.
PA13 JTMS-SWDIO SWD
PA14 JTCK-SWCLK SWD
# PWM output for buzzer
PA15 TIM2_CH1 TIM2 GPIO(77) ALARM
# First I2C bus.
PB8 I2C1_SCL I2C1
PB9 I2C1_SDA I2C1
# microSD card
PC8 SDMMC1_D0 SDMMC1
PC9 SDMMC1_D1 SDMMC1
PC10 SDMMC1_D2 SDMMC1
PC11 SDMMC1_D3 SDMMC1
PC12 SDMMC1_CK SDMMC1
PD2 SDMMC1_CMD SDMMC1
# CS pins for SPI sensors. The labels for all CS pins need to
# match the SPI device table later in this file.
PC2 ICM_20602_CS CS
PD7 BARO_CS CS
PD10 FRAM_CS CS SPEED_VERYLOW NODMA
PE15 ICM_20948_CS CS
PF6 BMI088_ACCEL_CS CS
PF10 BMI088_GYRO_CS CS
PG9 EXTERNAL CS
# CAN Busses
PD0 CAN1_RX CAN1
PD1 CAN1_TX CAN1
# CAN Silent Pin LOW Enable
PF5 GPIO_CAN_SILENT OUTPUT PUSHPULL SPEED_LOW LOW GPIO(72)
# Now we start defining some PWM pins. We also map these pins to GPIO
# values, so users can set BRD_PWM_COUNT to choose how many of the PWM
# outputs on the primary MCU are setup as PWM and how many as
# GPIOs. To match HAL_PX4 we number the GPIOs for the PWM outputs
# starting at 50.
PE14 TIM1_CH4 TIM1 PWM(1) GPIO(50)
PE13 TIM1_CH3 TIM1 PWM(2) GPIO(51)
PE11 TIM1_CH2 TIM1 PWM(3) GPIO(52)
PE9 TIM1_CH1 TIM1 PWM(4) GPIO(53)
PD13 TIM4_CH2 TIM4 PWM(5) GPIO(54)
PD14 TIM4_CH3 TIM4 PWM(6) GPIO(55)
PI5 TIM8_CH1 TIM8 PWM(7) GPIO(56)
PI6 TIM8_CH2 TIM8 PWM(8) GPIO(57)
define BOARD_PWM_COUNT_DEFAULT 8
# This is the invensense 20602 data-ready pin.
PD15 MPU_DRDY INPUT
# Power Supply Enable
PE3 VDD_1V8_3V3_SENSORS_EN OUTPUT HIGH
# Power Supply Enable 3.3v Periph/Spektrum
PC5 VDD_3V3_PERIPH_EN OUTPUT HIGH
# Power flag pins: these tell the MCU the status of the various power
# supplies that are available. The pin names need to exactly match the
# names used in AnalogIn.cpp.
PB5 VDD_BRICK_VALID INPUT PULLDOWN
SPIDEV dps280 SPI2 DEVID3 BARO_CS MODE3 5*MHZ 5*MHZ
SPIDEV ramtron SPI2 DEVID10 FRAM_CS MODE3 8*MHZ 8*MHZ
SPIDEV bmi088_g SPI5 DEVID1 BMI088_GYRO_CS MODE3 5*MHZ 5*MHZ
SPIDEV bmi088_a SPI5 DEVID2 BMI088_ACCEL_CS MODE3 5*MHZ 5*MHZ
SPIDEV icm20608 SPI1 DEVID2 ICM_20602_CS MODE3 2*MHZ 4*MHZ
SPIDEV icm20948 SPI1 DEVID1 ICM_20948_CS MODE3 2*MHZ 4*MHZ
# Now some defines for logging and terrain data files.
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"
# Enable RAMTROM parameter storage.
define HAL_WITH_RAMTRON 1
# Enable FAT filesystem support (needs a microSD defined via SDMMC).
define HAL_OS_FATFS_IO 1
# Control Zero has a TriColor LED, Red, Green, Blue
define HAL_HAVE_PIXRACER_LED
define HAL_GPIO_LED_ON 0
define HAL_GPIO_LED_OFF 1
# LED setup for PixracerLED driver
PB11 LED_R OUTPUT HIGH GPIO(0)
PB1 LED_G OUTPUT HIGH GPIO(1)
PB3 LED_B OUTPUT HIGH GPIO(2)
define HAL_GPIO_A_LED_PIN 0
define HAL_GPIO_B_LED_PIN 1
define HAL_GPIO_C_LED_PIN 2
# 3 IMUs
IMU BMI088 SPI:bmi088_a SPI:bmi088_g ROTATION_NONE
IMU Invensense SPI:icm20608 ROTATION_ROLL_180_YAW_90
IMU Invensensev2 SPI:icm20948 ROTATION_ROLL_180_YAW_90
define HAL_DEFAULT_INS_FAST_SAMPLE 7
# 1 baro
BARO DPS280 SPI:dps280
# 1 compass
COMPASS AK09916:probe_ICM20948 0 ROTATION_ROLL_180
define HAL_PROBE_EXTERNAL_I2C_COMPASSES

8
libraries/AP_HAL_ChibiOS/hwdef/mRoControlZeroOEMH7/defaults.parm Normal file
View File

@ -0,0 +1,8 @@
#Default Parameters for the mRo Control Zero OEM H7
CAN_P1_DRIVER 1
CAN_P2_DRIVER 2
CAN_SLCAN_CPORT 1
SERIAL6_PROTOCOL 22

66
libraries/AP_HAL_ChibiOS/hwdef/mRoControlZeroOEMH7/hwdef-bl.dat Normal file
View File

@ -0,0 +1,66 @@
###########################################################################################################################################################
# mRo Control Zero OEM H7 Flight Controller
# STM32H743IIK6
# 8x PWM / IO - DMA capable and hardware and/or software switchable 3.3v / 5v Logic (hardware default)
# Logic level set in hardware: No Solder for 5v, Solder 1-2 for 3.3v, Solder 2-3 for 3.3v / 5v software switchable
# Bottom Connectors: 36pin front and 40pin back Samtec FTM-118-02-F-DV 1.00 mm Surface Mount Micro Low Profile Terminal Strip
# 3x IMUs (BMI088 6DOF, ICM20602 6DOF, ICM20948 9DOF)
# DPS310 Baro, FRAM (256Bb), SDCARD Socket, TC2030 JTAG
# 5x UARTs (2x with hardware flow control), 2x CAN, 1x SPI, 3x I2C
# Onboard 3 color LED and buzzer
# Uncased Weight and Dimensions:
# Weight: 3.66g (13.oz)
# Width: 20mm (.79in)
# Length: 34mm (1.34in)
# M10059C - Initial Release
###########################################################################################################################################################
# MCU class and specific type
MCU STM32H7xx STM32H743xx
# USB setup
USB_STRING_MANUFACTURER "mRo"
# crystal frequency
OSCILLATOR_HZ 24000000
# board ID for firmware load
APJ_BOARD_ID 1024
FLASH_SIZE_KB 2048
# bootloader is installed at zero offset
FLASH_RESERVE_START_KB 0
# the location where the bootloader will put the firmware
FLASH_BOOTLOADER_LOAD_KB 128
PB11 LED_BOOTLOADER OUTPUT
# define all 3 to make LED output White.
PB1 LED_ACTIVITY OUTPUT
PB3 LED_ACTIVITY2 OUTPUT
# PB11 LED_ACTIVITY3 OUTPUT
define HAL_LED_ON 0
# order of UARTs (and USB)
SERIAL_ORDER OTG1
PA11 OTG_FS_DM OTG1
PA12 OTG_FS_DP OTG1
PA13 JTMS-SWDIO SWD
PA14 JTCK-SWCLK SWD
define HAL_USE_EMPTY_STORAGE 1
define HAL_STORAGE_SIZE 16384
# Add CS pins to ensure they are high in bootloader
PC2 ICM_20602_CS CS
PD7 BARO_CS CS
PD10 FRAM_CS CS SPEED_VERYLOW NODMA
PE15 ICM_20948_CS CS
PF6 BMI088_ACCEL_CS CS
PF10 BMI088_GYRO_CS CS
PG9 EXTERNAL CS

279
libraries/AP_HAL_ChibiOS/hwdef/mRoControlZeroOEMH7/hwdef.dat Normal file
View File

@ -0,0 +1,279 @@
###########################################################################################################################################################
# mRo Control Zero OEM H7 Flight Controller
# STM32H743IIK6
# 8x PWM / IO - DMA capable and hardware and/or software switchable 3.3v / 5v Logic (hardware default)
# Logic level set in hardware: No Solder for 5v, Solder 1-2 for 3.3v, Solder 2-3 for 3.3v / 5v software switchable
# Bottom Connectors: 36pin front and 40pin back Samtec FTM-118-02-F-DV 1.00 mm Surface Mount Micro Low Profile Terminal Strip
# 3x IMUs (BMI088 6DOF, ICM20602 6DOF, ICM20948 9DOF)
# DPS310 Baro, FRAM (256Bb), SDCARD Socket, TC2030 JTAG
# 5x UARTs (2x with hardware flow control), 2x CAN, 1x SPI, 3x I2C
# Onboard 3 color LED and buzzer
# Uncased Weight and Dimensions:
# Weight: 3.66g (13.oz)
# Width: 20mm (.79in)
# Length: 34mm (1.34in)
# M10059C - Initial Release
###########################################################################################################################################################
# MCU class and specific type
MCU STM32H7xx STM32H743xx
# board ID for firmware load
APJ_BOARD_ID 1024
# crystal frequency
OSCILLATOR_HZ 24000000
FLASH_SIZE_KB 2048
# with 2M flash we can afford to optimize for speed
env OPTIMIZE -O2
# start on 2th sector (1st sector for bootloader)
FLASH_RESERVE_START_KB 128
define HAL_STORAGE_SIZE 16384
# USB setup
USB_STRING_MANUFACTURER "mRo"
# RC Input set for Interrupt not DMA
PC7 TIM3_CH2 TIM3 RCININT FLOAT LOW
# GPIO(70) # also USART6_RX for serial RC
# Control of Spektrum power pin
PE4 SPEKTRUM_PWR OUTPUT LOW GPIO(70)
define HAL_GPIO_SPEKTRUM_PWR 70
# Spektrum Power is Active High
define HAL_SPEKTRUM_PWR_ENABLED 0
# Spektrum RC Input pin, used as GPIO for bind for Satellite Receivers
PB0 SPEKTRUM_RC INPUT PULLUP GPIO(71)
define HAL_GPIO_SPEKTRUM_RC 71
# Order of I2C buses
I2C_ORDER I2C1 I2C3 I2C4
# this board has no internal I2C buses so them all external
define HAL_I2C_INTERNAL_MASK 0
# order of UARTs and suggested uses
# USART2 TELEM1
# USART3 TELEM2
# UART4 GPS
# UART8 FRSKY Telem
# UART7 DEBUG
# USART6 RC input (Only RX pin is connected)
# OTG1 and OTG2 are USB devices (1x physical USB connection enumerated as 2x logical ports)
SERIAL_ORDER OTG1 USART2 USART3 UART4 UART8 UART7 OTG2
# default the 2nd interface to MAVLink2 until MissionPlanner updates drivers
define HAL_OTG2_PROTOCOL SerialProtocol_MAVLink2
# Another USART, this one for telem1. This one has RTS and CTS lines.
# USART2 telem1
PD5 USART2_TX USART2
PD6 USART2_RX USART2
PD3 USART2_CTS USART2
PD4 USART2_RTS USART2
# The telem2 USART, this one for telem2. This one has RTS and CTS lines.
# USART3 telem2
PD8 USART3_TX USART3
PD9 USART3_RX USART3
PD11 USART3_CTS USART3
PD12 USART3_RTS USART3
# UART4 GPS
PA0 UART4_TX UART4
PA1 UART4_RX UART4
# UART7
PE8 UART7_TX UART7
PE7 UART7_RX UART7
# UART8 FrSky Telemetry (Single wire serial connects to the TX pin only)
PE1 UART8_TX UART8
PE0 UART8_RX UART8
# RSSI Analog Input
PC1 RSSI_IN ADC1
# Safety Switch Input
PC4 SAFETY_IN INPUT PULLDOWN
define HAL_HAVE_SAFETY_SWITCH 1
# Battery Analog Sense Pins
PA2 BATT_VOLTAGE_SENS ADC1 SCALE(1)
PA3 BATT_CURRENT_SENS ADC1 SCALE(1)
# Now the VDD sense pin. This is used to sense primary board voltage.
PA4 VDD_5V_SENS ADC1 SCALE(2)
# Now setup the default battery pins driver analog pins and default
# scaling for the power brick.
define HAL_BATT_VOLT_PIN 14
define HAL_BATT_CURR_PIN 15
define HAL_BATT_VOLT_SCALE 10.1
define HAL_BATT_CURR_SCALE 17.0
#SPI1 ICM_20602 / ICM_20948
PA5 SPI1_SCK SPI1
PA6 SPI1_MISO SPI1
PA7 SPI1_MOSI SPI1
#SPI2 FRAM / DPS310
PB10 SPI2_SCK SPI2
PB14 SPI2_MISO SPI2
PB15 SPI2_MOSI SPI2
#SPI5 BMI088
PF7 SPI5_SCK SPI5
PF8 SPI5_MISO SPI5
PF9 SPI5_MOSI SPI5
#SPI6 External
PG13 SPI6_SCK SPI6
PG12 SPI6_MISO SPI6
PG14 SPI6_MOSI SPI6
# This is the pin that senses USB being connected. It is an input pin
# setup as OPENDRAIN.
PA9 VBUS INPUT OPENDRAIN
# This input pin is used to detect that power is valid on USB.
PC0 VBUS_VALID INPUT PULLDOWN
# Now we define the pins that USB is connected on.
PA11 OTG_FS_DM OTG1
PA12 OTG_FS_DP OTG1
# These are the pins for SWD debugging with a STlinkv2 or black-magic probe.
PA13 JTMS-SWDIO SWD
PA14 JTCK-SWCLK SWD
# PWM output for buzzer
PA15 TIM2_CH1 TIM2 GPIO(77) ALARM
# First I2C bus.
PB8 I2C1_SCL I2C1
PB9 I2C1_SDA I2C1
# Second I2C bus.
PH7 I2C3_SCL I2C3
PH8 I2C3_SDA I2C3
# Third I2C bus.
PB6 I2C4_SCL I2C4
PB7 I2C4_SDA I2C4
# microSD card
PC8 SDMMC1_D0 SDMMC1
PC9 SDMMC1_D1 SDMMC1
PC10 SDMMC1_D2 SDMMC1
PC11 SDMMC1_D3 SDMMC1
PC12 SDMMC1_CK SDMMC1
PD2 SDMMC1_CMD SDMMC1
# CS pins for SPI sensors. The labels for all CS pins need to
# match the SPI device table later in this file.
PC2 ICM_20602_CS CS
PD7 BARO_CS CS
PD10 FRAM_CS CS SPEED_VERYLOW NODMA
PE15 ICM_20948_CS CS
PF6 BMI088_ACCEL_CS CS
PF10 BMI088_GYRO_CS CS
PG9 EXTERNAL CS
# CAN Busses
PD0 CAN1_RX CAN1
PD1 CAN1_TX CAN1
PB13 CAN2_TX CAN2
PB12 CAN2_RX CAN2
# CAN Silent Pins LOW Enable
PF5 GPIO_CAN_SILENT OUTPUT PUSHPULL SPEED_LOW LOW GPIO(72)
# Now we start defining some PWM pins. We also map these pins to GPIO
# values, so users can set BRD_PWM_COUNT to choose how many of the PWM
# outputs on the primary MCU are setup as PWM and how many as
# GPIOs. To match HAL_PX4 we number the GPIOs for the PWM outputs
# starting at 50.
PE14 TIM1_CH4 TIM1 PWM(1) GPIO(50)
PE13 TIM1_CH3 TIM1 PWM(2) GPIO(51)
PE11 TIM1_CH2 TIM1 PWM(3) GPIO(52)
PE9 TIM1_CH1 TIM1 PWM(4) GPIO(53)
PD13 TIM4_CH2 TIM4 PWM(5) GPIO(54)
PD14 TIM4_CH3 TIM4 PWM(6) GPIO(55)
PI5 TIM8_CH1 TIM8 PWM(7) GPIO(56)
PI6 TIM8_CH2 TIM8 PWM(8) GPIO(57)
define BOARD_PWM_COUNT_DEFAULT 8
# This is the invensense 20602 data-ready pin.
PD15 MPU_DRDY INPUT
# Power Supply Enable
PE3 VDD_1V8_3V3_SENSORS_EN OUTPUT HIGH
# Power Supply Enable 3.3v Periph/Spektrum
PC5 VDD_3V3_PERIPH_EN OUTPUT HIGH
# Power flag pins: these tell the MCU the status of the various power
# supplies that are available. The pin names need to exactly match the
# names used in AnalogIn.cpp.
PB5 VDD_BRICK_VALID INPUT PULLDOWN
SPIDEV dps280 SPI2 DEVID3 BARO_CS MODE3 5*MHZ 5*MHZ
SPIDEV ramtron SPI2 DEVID10 FRAM_CS MODE3 8*MHZ 8*MHZ
SPIDEV bmi088_g SPI5 DEVID1 BMI088_GYRO_CS MODE3 5*MHZ 5*MHZ
SPIDEV bmi088_a SPI5 DEVID2 BMI088_ACCEL_CS MODE3 5*MHZ 5*MHZ
SPIDEV icm20608 SPI1 DEVID2 ICM_20602_CS MODE3 2*MHZ 4*MHZ
SPIDEV icm20948 SPI1 DEVID1 ICM_20948_CS MODE3 2*MHZ 4*MHZ
# Now some defines for logging and terrain data files.
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"
# Enable RAMTROM parameter storage.
define HAL_WITH_RAMTRON 1
# Enable FAT filesystem support (needs a microSD defined via SDMMC).
define HAL_OS_FATFS_IO 1
# Control Zero has a TriColor LED, Red, Green, Blue
define HAL_HAVE_PIXRACER_LED
define HAL_GPIO_LED_ON 0
define HAL_GPIO_LED_OFF 1
# LED setup for PixracerLED driver
PB11 LED_R OUTPUT HIGH GPIO(0)
PB1 LED_G OUTPUT HIGH GPIO(1)
PB3 LED_B OUTPUT HIGH GPIO(2)
define HAL_GPIO_A_LED_PIN 0
define HAL_GPIO_B_LED_PIN 1
define HAL_GPIO_C_LED_PIN 2
# DMA_PRIORITY SDMMC*
# 3 IMUs
IMU BMI088 SPI:bmi088_a SPI:bmi088_g ROTATION_NONE
IMU Invensense SPI:icm20608 ROTATION_ROLL_180_YAW_90
IMU Invensensev2 SPI:icm20948 ROTATION_ROLL_180_YAW_90
define HAL_DEFAULT_INS_FAST_SAMPLE 7
# 1 baro
BARO DPS280 SPI:dps280
# 1 compass
COMPASS AK09916:probe_ICM20948 0 ROTATION_ROLL_180
define HAL_PROBE_EXTERNAL_I2C_COMPASSES

7
libraries/AP_HAL_ChibiOS/hwdef/mRoPixracerPro/defaults.parm Normal file
View File

@ -0,0 +1,7 @@
#Default Parameters for the mRo Pixracer Pro
CAN_P1_DRIVER 1
CAN_P2_DRIVER 2
CAN_SLCAN_CPORT 1
SERIAL6_PROTOCOL 22

23
libraries/AP_HAL_ChibiOS/hwdef/mRoPixracerPro/hwdef-bl.dat
View File

@ -1,13 +1,18 @@
###########################################################################################################################################################
# mRo Pixracer Pro Flight Controller
# STM32H753IIK6
# 8 PWM / IO - DMA capable and switchable 3.3v (default) / 5v Logic
# Exposed JST GH Connectors: GPS UART+I2C connector, 5 Available UARTS (2 with Flow Control), 2 FDCAN, SPI, Power with analog current and voltage sense
# STM32H743IIK6
# 8 PWM / IO - DMA capable and hardware and/or software switchable 3.3v / 5v Logic (hardware default)
# Logic level set in hardware: No Solder for 5v, Solder 1-2 for 3.3v, Solder 2-3 for 3.3v / 5v software switchable
# Exposed JST GH Connectors: GPS UART+I2C connector, 6 Available UARTS (2 with Flow Control), 2 FDCAN, SPI, I2C, Power with analog current and voltage sense
# 3 IMUs (ICM20602 6DOF, ICM20948 9DOF, BMI088 6DOF)
# Baro, FRAM (256kb), SDCARD Socket, TC2030 JTAG
# Baro, FRAM (256kb), SDCARD Socket, TC2030 JTAG, USB-C
# Onboard 3 color LED and buzzer
# 36mm x 36mm, 31.5mm x 31.5mm 4mm grommeted mounting holes for 3mm fasteners
# M10064B - Initial Release
# Uncased weight and dimensions:
# Weight (with headers): 11.3g (.40oz)
# Length: 36mm (1.42in)
# Width: 36mm (1.42in)
# Mounting holes: 31.5mm x 31.5mm 4mm grommeted mounting holes for 3mm fasteners
# M10064C - Initial Release
###########################################################################################################################################################
# MCU class and specific type
@ -40,11 +45,7 @@ PB3 LED_ACTIVITY2 OUTPUT
define HAL_LED_ON 0
# order of UARTs (and USB)
SERIAL_ORDER OTG1 UART7
# UART7 maps to uartF in the HAL (serial5 in SERIALn_ parameters).
PE7 UART7_RX UART7
PE8 UART7_TX UART7
SERIAL_ORDER OTG1
PA11 OTG_FS_DM OTG1
PA12 OTG_FS_DP OTG1

44
libraries/AP_HAL_ChibiOS/hwdef/mRoPixracerPro/hwdef.dat
View File

@ -1,15 +1,23 @@
###########################################################################################################################################################
# mRo Pixracer Pro Flight Controller
# STM32H753IIK6
# 8 PWM / IO - DMA capable and switchable 3.3v (default) / 5v Logic
# Exposed JST GH Connectors: GPS UART+I2C connector, 5 Available UARTS (2 with Flow Control), 2 FDCAN, SPI, Power with analog current and voltage sense
# STM32H743IIK6
# 8 PWM / IO - DMA capable and hardware and/or software switchable 3.3v / 5v Logic (hardware default)
# Logic level set in hardware: No Solder for 5v, Solder 1-2 for 3.3v, Solder 2-3 for 3.3v / 5v software switchable
# Exposed JST GH Connectors: GPS UART+I2C connector, 6 Available UARTS (2 with Flow Control), 2 FDCAN, SPI, I2C, Power with analog current and voltage sense
# 3 IMUs (ICM20602 6DOF, ICM20948 9DOF, BMI088 6DOF)
# Baro, FRAM (256kb), SDCARD Socket, TC2030 JTAG
# Baro, FRAM (256kb), SDCARD Socket, TC2030 JTAG, USB-C
# Onboard 3 color LED and buzzer
# 36mm x 36mm, 31.5mm x 31.5mm 4mm grommeted mounting holes for 3mm fasteners
# M10064B - Initial Release
# Uncased weight and dimensions:
# Weight (with headers): 11.3g (.40oz)
# Length: 36mm (1.42in)
# Width: 36mm (1.42in)
# Mounting holes: 31.5mm x 31.5mm 4mm grommeted mounting holes for 3mm fasteners
# M10064C - Initial Release
###########################################################################################################################################################
# default to all pins low to avoid ESD issues
DEFAULTGPIO OUTPUT LOW PULLDOWN
# MCU class and specific type
MCU STM32H7xx STM32H743xx
@ -34,8 +42,8 @@ define HAL_WITH_RAMTRON 1
# USB setup
USB_STRING_MANUFACTURER "mRo"
# RC Input set for Interrupt not DMA
PC7 TIM3_CH2 TIM3 RCININT FLOAT LOW # also USART6_RX for serial RC
# RC Input set for Interrupt also USART6_RX for serial RC
PC7 TIM3_CH2 TIM3 RCININT FLOAT LOW
# Control of Spektrum power pin
PE4 SPEKTRUM_PWR OUTPUT LOW GPIO(70)
@ -55,14 +63,15 @@ I2C_ORDER I2C1
define HAL_I2C_INTERNAL_MASK 0
# order of UARTs (and USB) and suggested usage
# UART4 GPS
# USART2 Telem 1 (Flow Control)
# USART3 Telem 2 (Flow Control)
# UART4 GPS
# UART8 FRSKY Telem
# USART6 RC input (Only RX pin is connected)
# USART1 Additional UART
# UART7 Additional UART
# USART6 RC input (Only RX pin is connected)
SERIAL_ORDER OTG1 USART2 USART3 UART4 UART8 USART1 UART7 OTG2
# default the 2nd interface to MAVLink2
@ -209,8 +218,10 @@ PE3 VDD_3V3_SENSORS_EN OUTPUT HIGH
# 1.8V Sensor Level Shifter Output Enable. We pull it high by default.
PI3 VDD_1V8_SENSORS_EN OUTPUT HIGH
# Set Output Logic Level, Default is 3.3v
PG6 nSERVO_OUTPUT_3v3 OUTPUT LOW GPIO(74)
# Pin for PWM Voltage Selection, 0 means 3.3v, 1 means 5v
PG6 PWM_VOLT_SEL OUTPUT LOW GPIO(74)
define HAL_GPIO_PWM_VOLT_PIN 74
define HAL_GPIO_PWM_VOLT_3v3 0
# Power flag pins: these tell the MCU the status of the various power
# supplies that are available. The pin names need to exactly match the
@ -219,7 +230,7 @@ PB5 VDD_BRICK_VALID INPUT PULLUP
SPIDEV icm20948 SPI1 DEVID1 ICM_20948_CS MODE3 2*MHZ 4*MHZ
SPIDEV icm20608 SPI1 DEVID2 ICM_20602_CS MODE3 2*MHZ 8*MHZ
SPIDEV dps310 SPI2 DEVID3 BARO_CS MODE3 5*MHZ 5*MHZ
SPIDEV dps280 SPI2 DEVID3 BARO_CS MODE3 5*MHZ 5*MHZ
SPIDEV ramtron SPI2 DEVID10 FRAM_CS MODE3 8*MHZ 8*MHZ
SPIDEV bmi088_g SPI5 DEVID1 BMI088_GYRO_CS MODE3 10*MHZ 10*MHZ
SPIDEV bmi088_a SPI5 DEVID2 BMI088_ACCEL_CS MODE3 10*MHZ 10*MHZ
@ -256,18 +267,15 @@ define HAL_GPIO_A_LED_PIN 0
define HAL_GPIO_B_LED_PIN 1
define HAL_GPIO_C_LED_PIN 2
# DMA_PRIORITY SDMMC*
# DMA_NOSHARE SPI1* SPI2* SPI3*
# 3 IMUs
IMU BMI088 SPI:bmi088_a SPI:bmi088_g ROTATION_NONE
IMU Invensense SPI:icm20608 ROTATION_ROLL_180_YAW_90
IMU Invensensev2 SPI:icm20948 ROTATION_ROLL_180_YAW_90
define HAL_DEFAULT_INS_FAST_SAMPLE 5
define HAL_DEFAULT_INS_FAST_SAMPLE 7
# 1 baro
BARO DPS280 SPI:dps310
BARO DPS280 SPI:dps280
# 1 compass
COMPASS AK09916:probe_ICM20948 0 ROTATION_ROLL_180