mirror of
https://github.com/ArduPilot/ardupilot
synced 2025-02-02 14:08:45 -04:00
HAL_ChibiOS: added Pixracer docs
This commit is contained in:
Andrew Tridgell
parent
1d00d26b9e
commit
35db9c4b85
444
libraries/AP_HAL_ChibiOS/hwdef/Pixracer/README.md
Normal file
444
libraries/AP_HAL_ChibiOS/hwdef/Pixracer/README.md
Normal file
@ -0,0 +1,444 @@
|
|||||||
|
# Pixracer Flight Controller
|
||||||
|
|
||||||
|
The Pixracer flight controller is
|
||||||
|
[sold by mRobotics](https://store.mrobotics.io/category-s/112.htm)
|
||||||
|
|
||||||
|
The full schematics of the board are available here:
|
||||||
|
|
||||||
|
https://github.com/ArduPilot/Schematics/tree/master/mRobotics
|
||||||
|
|
||||||
|
## Features
|
||||||
|
|
||||||
|
- STM32F427 microcontroller
|
||||||
|
- MPU9250 and ICM20608 IMUs
|
||||||
|
- MS5611 SPI barometer
|
||||||
|
- builtin HMC5843 and MPU9250 magnetometers
|
||||||
|
- microSD card slot
|
||||||
|
- 6 UARTs plus USB
|
||||||
|
- 6 PWM outputs
|
||||||
|
- I2C and CAN ports
|
||||||
|
- Spektrum satellite cable
|
||||||
|
- External Buzzer
|
||||||
|
- builtin RGB LEDs
|
||||||
|
- external safety Switch
|
||||||
|
- voltage monitoring for servo rail and Vcc
|
||||||
|
- dedicated power input port for external power brick
|
||||||
|
|
||||||
|
## Pinout
|
||||||
|
|
||||||
|
|
||||||
|
|
||||||
|
|
||||||
|
## UART Mapping
|
||||||
|
|
||||||
|
- SERIAL0 -> USB
|
||||||
|
- SERIAL1 -> UART2 (Telem1)
|
||||||
|
- SERIAL2 -> UART3 (Telem2)
|
||||||
|
- SERIAL3 -> UART4 (GPS)
|
||||||
|
- SERIAL4 -> UART8 (GPS2, FrSky Telem)
|
||||||
|
- SERIAL5 -> UART1 (spare)
|
||||||
|
- SERIAL6 -> UART7 (spare, debug port)
|
||||||
|
|
||||||
|
The Telem1 and Telem2 ports have RTS/CTS pins, the other UARTs do not
|
||||||
|
have RTS/CTS.
|
||||||
|
|
||||||
|
## Connectors
|
||||||
|
|
||||||
|
Unless noted otherwise all connectors are JST GH
|
||||||
|
|
||||||
|
### TELEM1, TELEM2+OSD ports
|
||||||
|
|
||||||
|
<table border="1" class="docutils">
|
||||||
|
<tbody>
|
||||||
|
<tr>
|
||||||
|
<th>Pin</th>
|
||||||
|
<th>Signal</th>
|
||||||
|
<th>Volt</th>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>1 (red)</td>
|
||||||
|
<td>VCC</td>
|
||||||
|
<td>+5V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>2 (blk)</td>
|
||||||
|
<td>TX (OUT)</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>3 (blk)</td>
|
||||||
|
<td>RX (IN)</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>4 (blk)</td>
|
||||||
|
<td>CTS (IN)</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>5 (blk)</td>
|
||||||
|
<td>RTS (OUT)</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>6 (blk)</td>
|
||||||
|
<td>GND</td>
|
||||||
|
<td>GND</td>
|
||||||
|
</tr>
|
||||||
|
</tbody>
|
||||||
|
</table>
|
||||||
|
|
||||||
|
### GPS port
|
||||||
|
|
||||||
|
<table border="1" class="docutils">
|
||||||
|
<tbody>
|
||||||
|
<tr>
|
||||||
|
<th>PIN</th>
|
||||||
|
<th>SIGNAL</th>
|
||||||
|
<th>VOLT</th>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>1 (red)</td>
|
||||||
|
<td>VCC</td>
|
||||||
|
<td>+5V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>2 (blk)</td>
|
||||||
|
<td>TX (OUT)</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>3 (blk)</td>
|
||||||
|
<td>RX (IN)</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>4 (blk)</td>
|
||||||
|
<td>I2C1 SCL</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>5 (blk)</td>
|
||||||
|
<td>I2C1 SDA</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>6 (blk)</td>
|
||||||
|
<td>GND</td>
|
||||||
|
<td>GND</td>
|
||||||
|
</tr>
|
||||||
|
</tbody>
|
||||||
|
</table>
|
||||||
|
|
||||||
|
### FrSky Telemetry / SERIAL4
|
||||||
|
|
||||||
|
This UART is inverted by default. You can disable the inverter by
|
||||||
|
setting SERIAL4_OPTIONS=2 if you want to use it with a non-inverted
|
||||||
|
protocol.
|
||||||
|
|
||||||
|
<table border="1" class="docutils">
|
||||||
|
<tbody>
|
||||||
|
<tr>
|
||||||
|
<th>PIN</th>
|
||||||
|
<th>SIGNAL</th>
|
||||||
|
<th>VOLT</th>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>1 (red)</td>
|
||||||
|
<td>VCC</td>
|
||||||
|
<td>+5V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>2 (blk)</td>
|
||||||
|
<td>TX (OUT)</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>3 (blk)</td>
|
||||||
|
<td>RX (IN)</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>4 (blk)</td>
|
||||||
|
<td>GND</td>
|
||||||
|
<td>GND</td>
|
||||||
|
</tr>
|
||||||
|
</tbody>
|
||||||
|
</table>
|
||||||
|
|
||||||
|
### RC Input (accepts all RC protocols)
|
||||||
|
|
||||||
|
<table border="1" class="docutils">
|
||||||
|
<tbody>
|
||||||
|
<tr>
|
||||||
|
<th>PIN</th>
|
||||||
|
<th>SIGNAL</th>
|
||||||
|
<th>VOLT</th>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>1 (red)</td>
|
||||||
|
<td>VCC</td>
|
||||||
|
<td>+5V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>2 (blk)</td>
|
||||||
|
<td>RC IN</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>3 (blk)</td>
|
||||||
|
<td>RSSI IN</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>4 (blk)</td>
|
||||||
|
<td>VDD 3V3</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>5 (blk)</td>
|
||||||
|
<td>GND</td>
|
||||||
|
<td>GND</td>
|
||||||
|
</tr>
|
||||||
|
</tbody>
|
||||||
|
</table>
|
||||||
|
|
||||||
|
### CAN
|
||||||
|
|
||||||
|
<table border="1" class="docutils">
|
||||||
|
<tbody>
|
||||||
|
<tr>
|
||||||
|
<th>PIN</th>
|
||||||
|
<th>SIGNAL</th>
|
||||||
|
<th>VOLT</th>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>1 (red)</td>
|
||||||
|
<td>VCC</td>
|
||||||
|
<td>+5V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>2 (blk)</td>
|
||||||
|
<td>CAN_H</td>
|
||||||
|
<td>+12V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>3 (blk)</td>
|
||||||
|
<td>CAN_L</td>
|
||||||
|
<td>+12V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>4 (blk)</td>
|
||||||
|
<td>GND</td>
|
||||||
|
<td>GND</td>
|
||||||
|
</tr>
|
||||||
|
</tbody>
|
||||||
|
</table>
|
||||||
|
|
||||||
|
### Power
|
||||||
|
|
||||||
|
<table border="1" class="docutils">
|
||||||
|
<tbody>
|
||||||
|
<tr>
|
||||||
|
<th>PIN</th>
|
||||||
|
<th>SIGNAL</th>
|
||||||
|
<th>VOLT</th>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>1 (red)</td>
|
||||||
|
<td>VCC</td>
|
||||||
|
<td>+5V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>2 (blk)</td>
|
||||||
|
<td>VCC</td>
|
||||||
|
<td>+5V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>3 (blk)</td>
|
||||||
|
<td>CURRENT</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>4 (blk)</td>
|
||||||
|
<td>VOLTAGE</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>5 (blk)</td>
|
||||||
|
<td>GND</td>
|
||||||
|
<td>GND</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>6 (blk)</td>
|
||||||
|
<td>GND</td>
|
||||||
|
<td>GND</td>
|
||||||
|
</tr>
|
||||||
|
</tbody>
|
||||||
|
</table>
|
||||||
|
|
||||||
|
### Switch
|
||||||
|
|
||||||
|
<table border="1" class="docutils">
|
||||||
|
<tbody>
|
||||||
|
<tr>
|
||||||
|
<th>PIN</th>
|
||||||
|
<th>SIGNAL</th>
|
||||||
|
<th>VOLT</th>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>1 (red)</td>
|
||||||
|
<td>SAFETY</td>
|
||||||
|
<td>GND</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>2 (blk)</td>
|
||||||
|
<td>!IO_LED_SAFETY</td>
|
||||||
|
<td>GND</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>3 (blk)</td>
|
||||||
|
<td>CURRENT</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>4 (blk)</td>
|
||||||
|
<td>BUZZER-</td>
|
||||||
|
<td>-</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>5 (blk)</td>
|
||||||
|
<td>BUZZER+</td>
|
||||||
|
<td>-</td>
|
||||||
|
</tr>
|
||||||
|
</tbody>
|
||||||
|
</table>
|
||||||
|
|
||||||
|
### Debug port (JST SM06B connector)
|
||||||
|
|
||||||
|
Note that in ArduPilot the debug UART is available as a general
|
||||||
|
purpose UART.
|
||||||
|
|
||||||
|
<table border="1" class="docutils">
|
||||||
|
<tbody>
|
||||||
|
<tr>
|
||||||
|
<th>PIN</th>
|
||||||
|
<th>SIGNAL</th>
|
||||||
|
<th>VOLT</th>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>1 (red)</td>
|
||||||
|
<td>VCC TARGET SHIFT</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>2 (blk)</td>
|
||||||
|
<td>CONSOLE TX (OUT)</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>3 (blk)</td>
|
||||||
|
<td>CONSOLE RX (IN)</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>4 (blk)</td>
|
||||||
|
<td>SWDIO</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>5 (blk)</td>
|
||||||
|
<td>SWCLK</td>
|
||||||
|
<td>+3.3V</td>
|
||||||
|
</tr>
|
||||||
|
<tr>
|
||||||
|
<td>6 (blk)</td>
|
||||||
|
<td>GND</td>
|
||||||
|
<td>GND</td>
|
||||||
|
</tr>
|
||||||
|
</tbody>
|
||||||
|
</table>
|
||||||
|
|
||||||
|
## RC Input
|
||||||
|
|
||||||
|
RC input is via a RC input cable. That cable comes in two forms, one
|
||||||
|
for Spektrum satellite receivers and another for all other receiver
|
||||||
|
types.
|
||||||
|
|
||||||
|
Both cables support all protocols with ArduPilot, but you need to use
|
||||||
|
the Spektrum cable if you want to be able to bind the receiver using
|
||||||
|
the ArduPilot binding support as only the Spektrum cable gives
|
||||||
|
ArduPilot the ability to control the power on the Spektrum satellite
|
||||||
|
receiver.
|
||||||
|
|
||||||
|
## FrSky Telemetry
|
||||||
|
|
||||||
|
FrSky Telemetry is supported using SERIAL4, on the port marked as
|
||||||
|
FrSky. You need to set the following parameters to enable support for
|
||||||
|
FrSky S.PORT
|
||||||
|
|
||||||
|
- SERIAL4_PROTOCOL 10
|
||||||
|
- SERIAL4_OPTIONS 0
|
||||||
|
|
||||||
|
## PWM Output
|
||||||
|
|
||||||
|
The Pixracer supports up to 6 PWM outputs. All 6 outputs can support
|
||||||
|
DShot as well as all PWM protocols.
|
||||||
|
|
||||||
|
The 6 PWM outputs are in 2 groups:
|
||||||
|
|
||||||
|
- PWM 1, 2, 3 and 4 in group1
|
||||||
|
- PWM 5 and 6 in group2
|
||||||
|
|
||||||
|
Channels within the same group need to use the same output rate. If
|
||||||
|
any channel in a group uses DShot then all channels in the group need
|
||||||
|
to use DShot.
|
||||||
|
|
||||||
|
## Battery Monitoring
|
||||||
|
|
||||||
|
The board has a dedicated power monitor port on a 6 pin connector. The
|
||||||
|
correct battery setting parameters are dependent on the type of power
|
||||||
|
brick which is connected.
|
||||||
|
|
||||||
|
## Compass
|
||||||
|
|
||||||
|
The Pixracer has two builtin compasses. One is a HMC5843 and the other
|
||||||
|
is a part of the MPU9250 IMU. Due to potential interference the board
|
||||||
|
is usually used with an external I2C compass as part of a GPS/Compass
|
||||||
|
combination.
|
||||||
|
|
||||||
|
## GPIOs
|
||||||
|
|
||||||
|
The 6 PWM ports can be used as GPIOs (relays, buttons, RPM etc). To
|
||||||
|
use them you need to limit the number of these pins that is used for
|
||||||
|
PWM by setting the BRD_PWM_COUNT to a number less than 6. For example
|
||||||
|
if you set BRD_PWM_COUNT to 4 then PWM5 and PWM6 will be available for
|
||||||
|
use as GPIOs.
|
||||||
|
|
||||||
|
The numbering of the GPIOs for PIN variables in ArduPilot is:
|
||||||
|
|
||||||
|
- PWM1 50
|
||||||
|
- PWM2 51
|
||||||
|
- PWM3 52
|
||||||
|
- PWM4 53
|
||||||
|
- PWM5 54
|
||||||
|
- PWM6 55
|
||||||
|
|
||||||
|
## Analog inputs
|
||||||
|
|
||||||
|
The Pixracer has 4 analog inputs
|
||||||
|
|
||||||
|
- ADC Pin2 -> Battery Voltage
|
||||||
|
- ADC Pin3 -> Battery Current Sensor
|
||||||
|
- ADC Pin4 -> Vdd 5V supply sense
|
||||||
|
- ADC Pin11 -> Analog RSSI Input
|
||||||
|
|
||||||
|
## Loading Firmware
|
||||||
|
|
||||||
|
The board comes pre-installed with an ArduPilot compatible bootloader,
|
||||||
|
allowing the loading of *.apj firmware files with any ArduPilot
|
||||||
|
compatible ground station.
|
||||||
|
|
||||||
|
## Acknowledgements
|
||||||
|
|
||||||
|
Thanks to [mRobotics](http://mrobotics.io/) and the [PX4 project](https://docs.px4.io/en/flight_controller/pixracer.html) for images
|
||||||
Binary file not shown.
|
After Width: | Height: | Size: 174 KiB |
Binary file not shown.
|
After Width: | Height: | Size: 186 KiB |
@ -133,9 +133,6 @@ PD10 FRAM_CS CS
|
|||||||
PD11 USART3_CTS USART3
|
PD11 USART3_CTS USART3
|
||||||
PD12 USART3_RTS USART3
|
PD12 USART3_RTS USART3
|
||||||
|
|
||||||
PD13 TIM4_CH2 TIM4 PWM(5) GPIO(54)
|
|
||||||
PD14 TIM4_CH3 TIM4 PWM(6) GPIO(55)
|
|
||||||
|
|
||||||
PD15 MPU9250_DRDY INPUT
|
PD15 MPU9250_DRDY INPUT
|
||||||
|
|
||||||
# UART8 serial4 FrSky
|
# UART8 serial4 FrSky
|
||||||
@ -153,11 +150,14 @@ PE3 VDD_SENSORS_EN OUTPUT HIGH
|
|||||||
PE7 UART7_RX UART7 NODMA
|
PE7 UART7_RX UART7 NODMA
|
||||||
PE8 UART7_TX UART7 NODMA
|
PE8 UART7_TX UART7 NODMA
|
||||||
|
|
||||||
PE9 TIM1_CH1 TIM1 PWM(4) GPIO(53)
|
|
||||||
PE11 TIM1_CH2 TIM1 PWM(3) GPIO(52)
|
|
||||||
PE12 MAG_DRDY INPUT
|
|
||||||
PE13 TIM1_CH3 TIM1 PWM(2) GPIO(51)
|
|
||||||
PE14 TIM1_CH4 TIM1 PWM(1) GPIO(50)
|
PE14 TIM1_CH4 TIM1 PWM(1) GPIO(50)
|
||||||
|
PE13 TIM1_CH3 TIM1 PWM(2) GPIO(51)
|
||||||
|
PE11 TIM1_CH2 TIM1 PWM(3) GPIO(52)
|
||||||
|
PE9 TIM1_CH1 TIM1 PWM(4) GPIO(53)
|
||||||
|
PD13 TIM4_CH2 TIM4 PWM(5) GPIO(54)
|
||||||
|
PD14 TIM4_CH3 TIM4 PWM(6) GPIO(55)
|
||||||
|
|
||||||
|
PE12 MAG_DRDY INPUT
|
||||||
PE15 MAG_CS CS
|
PE15 MAG_CS CS
|
||||||
|
|
||||||
# SPI device table. The DEVID values are chosen to match the PX4 port
|
# SPI device table. The DEVID values are chosen to match the PX4 port
|
||||||
|
|||||||
Loading…
Reference in New Issue
Block a user