mirror of https://github.com/ArduPilot/ardupilot
HAL_ChibiOS: added support for MatekF765-Wing
This commit is contained in:
Andrew Tridgell
parent
1ffc2cbe41
commit
2f79639e36
|
|
@ -0,0 +1,52 @@
|
|||
# hw definition file for processing by chibios_pins.py
|
||||
# for Matek F765-Wing bootloader
|
||||
|
||||
# MCU class and specific type
|
||||
MCU STM32F7xx STM32F767xx
|
||||
|
||||
# board ID for firmware load
|
||||
APJ_BOARD_ID 143
|
||||
|
||||
# crystal frequency, setup to use external oscillator
|
||||
OSCILLATOR_HZ 8000000
|
||||
|
||||
define STM32_LSECLK 32768U
|
||||
define STM32_LSEDRV (3U << 3U)
|
||||
|
||||
define STM32_PLLSRC STM32_PLLSRC_HSE
|
||||
define STM32_PLLM_VALUE 8
|
||||
define STM32_PLLN_VALUE 432
|
||||
define STM32_PLLP_VALUE 2
|
||||
define STM32_PLLQ_VALUE 9
|
||||
|
||||
FLASH_SIZE_KB 2048
|
||||
|
||||
# bootloader starts at zero offset
|
||||
FLASH_RESERVE_START_KB 0
|
||||
|
||||
# the location where the bootloader will put the firmware
|
||||
FLASH_BOOTLOADER_LOAD_KB 96
|
||||
|
||||
# board voltage
|
||||
STM32_VDD 330U
|
||||
|
||||
# order of UARTs (and USB). Allow bootloading on USB and telem1
|
||||
UART_ORDER OTG1 UART7
|
||||
|
||||
# UART7 (telem1)
|
||||
PE7 UART7_RX UART7
|
||||
PE8 UART7_TX UART7
|
||||
|
||||
# PA10 IO-debug-console
|
||||
PA11 OTG_FS_DM OTG1
|
||||
PA12 OTG_FS_DP OTG1
|
||||
|
||||
PA13 JTMS-SWDIO SWD
|
||||
PA14 JTCK-SWCLK SWD
|
||||
|
||||
PD10 LED_BOOTLOADER OUTPUT LOW
|
||||
define HAL_LED_ON 0
|
||||
|
||||
define HAL_USE_EMPTY_STORAGE 1
|
||||
define HAL_STORAGE_SIZE 16384
|
||||
|
||||
|
|
@ -0,0 +1,211 @@
|
|||
# hw definition file for processing by chibios_pins.py
|
||||
# for Matek F765-Wing
|
||||
|
||||
# MCU class and specific type
|
||||
MCU STM32F7xx STM32F767xx
|
||||
|
||||
# board ID for firmware load
|
||||
APJ_BOARD_ID 143
|
||||
|
||||
# crystal frequency, setup to use external oscillator
|
||||
OSCILLATOR_HZ 8000000
|
||||
|
||||
define STM32_LSECLK 32768U
|
||||
define STM32_LSEDRV (3U << 3U)
|
||||
|
||||
define STM32_PLLSRC STM32_PLLSRC_HSE
|
||||
define STM32_PLLM_VALUE 8
|
||||
define STM32_PLLN_VALUE 432
|
||||
define STM32_PLLP_VALUE 2
|
||||
define STM32_PLLQ_VALUE 9
|
||||
|
||||
FLASH_SIZE_KB 2048
|
||||
|
||||
# leave 2 sectors free
|
||||
FLASH_RESERVE_START_KB 96
|
||||
|
||||
# board voltage
|
||||
STM32_VDD 330U
|
||||
|
||||
STM32_ST_USE_TIMER 3
|
||||
define CH_CFG_ST_RESOLUTION 16
|
||||
|
||||
# two I2C bus
|
||||
I2C_ORDER I2C2 I2C1
|
||||
|
||||
# order of UARTs (and USB)
|
||||
UART_ORDER OTG1 USART2 UART7 USART1 USART3 UART8 UART4
|
||||
|
||||
# buzzer
|
||||
PB9 BUZZER OUTPUT GPIO(80) LOW
|
||||
define HAL_BUZZER_PIN 80
|
||||
define HAL_BUZZER_ON 1
|
||||
define HAL_BUZZER_OFF 0
|
||||
|
||||
# PA10 IO-debug-console
|
||||
PA11 OTG_FS_DM OTG1
|
||||
PA12 OTG_FS_DP OTG1
|
||||
|
||||
PA13 JTMS-SWDIO SWD
|
||||
PA14 JTCK-SWCLK SWD
|
||||
|
||||
# SPI1 for IMU1 (MPU6000)
|
||||
PA5 SPI1_SCK SPI1
|
||||
PA6 SPI1_MISO SPI1
|
||||
PA7 SPI1_MOSI SPI1
|
||||
PC4 IMU1_CS CS
|
||||
|
||||
# SPI2 for MAX7456 OSD
|
||||
PB12 MAX7456_CS CS
|
||||
PB13 SPI2_SCK SPI2
|
||||
PB14 SPI2_MISO SPI2
|
||||
PB15 SPI2_MOSI SPI2
|
||||
|
||||
# SPI3 for IMU2 (ICM20602)
|
||||
PB3 SPI3_SCK SPI3
|
||||
PB4 SPI3_MISO SPI3
|
||||
PB5 SPI3_MOSI SPI3
|
||||
PD7 IMU2_CS CS
|
||||
|
||||
# SPI4
|
||||
PE11 SPARE_CS CS
|
||||
PE12 SPI4_SCK SPI4
|
||||
PE13 SPI4_MISO SPI4
|
||||
PE14 SPI4_MOSI SPI4
|
||||
|
||||
# I2C1
|
||||
PB6 I2C1_SCL I2C1
|
||||
PB7 I2C1_SDA I2C1
|
||||
|
||||
# I2C2
|
||||
PB10 I2C2_SCL I2C2
|
||||
PB11 I2C2_SDA I2C2
|
||||
|
||||
PC2 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
||||
PC3 BATT_CURRENT_SENS ADC1 SCALE(1)
|
||||
|
||||
PA4 BATT_VOLTAGE_SENS2 ADC1 SCALE(1) # analog pin4
|
||||
PC5 BATT_CURRENT_SENS2 ADC1 SCALE(1) # analog pin15
|
||||
|
||||
PC0 PRESSURE_SENS ADC1 SCALE(2)
|
||||
define HAL_DEFAULT_AIRSPEED_PIN 10
|
||||
|
||||
# define default battery setup
|
||||
define HAL_BATT_VOLT_PIN 12
|
||||
define HAL_BATT_CURR_PIN 13
|
||||
define HAL_BATT_VOLT_SCALE 10.1
|
||||
define HAL_BATT_CURR_SCALE 17.0
|
||||
|
||||
# analog RSSI
|
||||
PC1 RSSI_ADC ADC1
|
||||
define BOARD_RSSI_ANA_PIN 11
|
||||
|
||||
PD10 LED0 OUTPUT LOW GPIO(90) # blue
|
||||
PD11 LED1 OUTPUT LOW GPIO(91) # green
|
||||
define HAL_GPIO_A_LED_PIN 91
|
||||
define HAL_GPIO_B_LED_PIN 90
|
||||
define HAL_GPIO_LED_OFF 1
|
||||
|
||||
# USART1 (telem2)
|
||||
PA10 USART1_RX USART1
|
||||
PA9 USART1_TX USART1
|
||||
|
||||
# USART2 (GPS1)
|
||||
PD5 USART2_TX USART2 NODMA
|
||||
PD6 USART2_RX USART2 NODMA
|
||||
|
||||
# USART3 (GPS2)
|
||||
PD9 USART3_RX USART3 NODMA
|
||||
PD8 USART3_TX USART3 NODMA
|
||||
|
||||
# UART4 (disable if used for CAN)
|
||||
PD1 UART4_TX UART4 NODMA
|
||||
PD0 UART4_RX UART4 NODMA
|
||||
|
||||
# UART5 (RX only, for ESC telem), disabled for now until we add uartH support
|
||||
# PB8 UART5_RX UART5 NODMA
|
||||
|
||||
# USART6 (RC input)
|
||||
PC7 TIM8_CH2 TIM8 RCININT FLOAT LOW
|
||||
PC6 USART6_TX USART6 NODMA LOW
|
||||
|
||||
# UART7 (telem1)
|
||||
PE7 UART7_RX UART7
|
||||
PE8 UART7_TX UART7
|
||||
PE10 UART7_CTS UART7
|
||||
PE9 UART7_RTS UART7
|
||||
|
||||
# UART8 (spare)
|
||||
PE0 UART8_RX UART8 NODMA
|
||||
PE1 UART8_TX UART8 NODMA
|
||||
|
||||
# CAN bus (disabled as used for UART4)
|
||||
#PD1 CAN1_TX CAN1
|
||||
#PD0 CAN1_RX CAN1
|
||||
|
||||
# Motors
|
||||
PA0 TIM2_CH1 TIM2 PWM(1) GPIO(50)
|
||||
PA1 TIM2_CH2 TIM2 PWM(2) GPIO(51)
|
||||
PA2 TIM5_CH3 TIM5 PWM(3) GPIO(52)
|
||||
PA3 TIM5_CH4 TIM5 PWM(4) GPIO(53)
|
||||
PB0 TIM1_CH2N TIM1 PWM(5) GPIO(54)
|
||||
PB1 TIM1_CH3N TIM1 PWM(6) GPIO(55)
|
||||
PD12 TIM4_CH1 TIM4 PWM(7) GPIO(56)
|
||||
PD13 TIM4_CH2 TIM4 PWM(8) GPIO(57)
|
||||
PD14 TIM4_CH3 TIM4 PWM(9) GPIO(58)
|
||||
PD15 TIM4_CH4 TIM4 PWM(10) GPIO(59)
|
||||
PE5 TIM9_CH1 TIM9 PWM(11) GPIO(60) NODMA
|
||||
PE6 TIM9_CH2 TIM9 PWM(12) GPIO(61) NODMA
|
||||
|
||||
# microSD support
|
||||
PC8 SDMMC_D0 SDMMC1
|
||||
PC9 SDMMC_D1 SDMMC1
|
||||
PC10 SDMMC_D2 SDMMC1
|
||||
PC11 SDMMC_D3 SDMMC1
|
||||
PC12 SDMMC_CK SDMMC1
|
||||
PD2 SDMMC_CMD SDMMC1
|
||||
|
||||
# GPIOs
|
||||
PE4 PINIO1 OUTPUT GPIO(81) LOW
|
||||
PE15 PINIO2 OUTPUT GPIO(82) LOW
|
||||
|
||||
# 2812 LED
|
||||
# PA8, TIM1_CH1
|
||||
|
||||
DMA_PRIORITY S*
|
||||
|
||||
define HAL_STORAGE_SIZE 16384
|
||||
define STORAGE_FLASH_PAGE 1
|
||||
|
||||
# spi devices
|
||||
SPIDEV mpu6000 SPI1 DEVID1 IMU1_CS MODE3 1*MHZ 4*MHZ
|
||||
SPIDEV icm20602 SPI3 DEVID1 IMU2_CS MODE3 1*MHZ 4*MHZ
|
||||
SPIDEV osd SPI2 DEVID4 MAX7456_CS MODE0 10*MHZ 10*MHZ
|
||||
|
||||
# no built-in compass, but probe the i2c bus for all possible
|
||||
# external compass types
|
||||
define ALLOW_ARM_NO_COMPASS
|
||||
define HAL_COMPASS_DEFAULT HAL_COMPASS_NONE
|
||||
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
||||
define HAL_I2C_INTERNAL_MASK 1
|
||||
define HAL_COMPASS_AUTO_ROT_DEFAULT 2
|
||||
|
||||
# two IMUs. We put icm20602 first as we can sample accel at 4kHz
|
||||
IMU Invensense SPI:icm20602 ROTATION_PITCH_180
|
||||
IMU Invensense SPI:mpu6000 ROTATION_ROLL_180
|
||||
define HAL_DEFAULT_INS_FAST_SAMPLE 1
|
||||
|
||||
# one BARO
|
||||
BARO BMP280 I2C:0:0x76
|
||||
|
||||
define HAL_OS_FATFS_IO 1
|
||||
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
|
||||
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"
|
||||
|
||||
# setup for OSD
|
||||
define OSD_ENABLED ENABLED
|
||||
define HAL_OSD_TYPE_DEFAULT 1
|
||||
ROMFS_WILDCARD libraries/AP_OSD/fonts/font*.bin
|
||||
|
||||
define BOARD_PWM_COUNT_DEFAULT 12
|
||||
|
||||
Loading…
Reference in New Issue