mirror of https://github.com/ArduPilot/ardupilot
AP_HAL_ChibiOS: hwdef for MambaH743v4
support BMI270 on MambaH743v4 and increase flash SPI clock add bi-directional dshot to MambaH743 add README and pinout for MambaH743
This commit is contained in:
parent
90e8bdba78
commit
22687bd545
Binary file not shown.
After Width: | Height: | Size: 104 KiB |
|
@ -0,0 +1,100 @@
|
|||
# MambaH743v4 Flight Controller
|
||||
|
||||
The MambaH743v4 is a flight controller produced by [Diatone](https://www.diatoneusa.com/).
|
||||
|
||||
## Features
|
||||
|
||||
- MCU - STM32H743 32-bit processor running at 480 MHz
|
||||
- IMU - Dual MPU6000 (Version A) or BMI270 (Version B)
|
||||
- Barometer - DPS280
|
||||
- OSD - AT7456E
|
||||
- Onboard Flash: 1GBit
|
||||
- 8x UARTs
|
||||
- 9x PWM Outputs (8 Motor Output, 1 LED)
|
||||
- Battery input voltage: 2S-6S
|
||||
- BEC 3.3V 0.5A
|
||||
- BEC 5V 3A
|
||||
- BEC 5V 3A
|
||||
- BEC 9V 3A
|
||||
|
||||
## Pinout
|
||||
|
||||
![MambaH743v4 Board](MambaH743v4_Board.jpg "MambaH743v4")
|
||||
|
||||
## UART Mapping
|
||||
|
||||
The UARTs are marked Rn and Tn in the above pinouts. The Rn pin is the
|
||||
receive pin for UARTn. The Tn pin is the transmit pin for UARTn.
|
||||
|
||||
- SERIAL0 -> USB
|
||||
- SERIAL1 -> UART1 (RX/SBUS, DMA-enabled)
|
||||
- SERIAL2 -> UART2
|
||||
- SERIAL3 -> UART3
|
||||
- SERIAL4 -> UART4 (GPS, DMA-enabled)
|
||||
- SERIAL5 -> UART5 (SPort)
|
||||
- SERIAL6 -> UART6 (ESC Telemetry)
|
||||
- SERIAL7 -> UART7 (GPS, DMA-enabled)
|
||||
|
||||
## RC Input
|
||||
|
||||
RC input is configured on the R1 (UART1_RX) pin. It supports all serial RC
|
||||
protocols. For protocols requiring half-duplex serial to transmit
|
||||
telemetry (such as FPort) you should setup SERIAL6 as an RC input serial port,
|
||||
with half-duplex, pin-swap and inversion enabled.
|
||||
|
||||
## FrSky Telemetry
|
||||
|
||||
FrSky Telemetry is supported using the T5 pin (UART5 transmit). You need to set the following parameters to enable support for FrSky S.PORT
|
||||
|
||||
- SERIAL5_PROTOCOL 10
|
||||
- SERIAL5_OPTIONS 7
|
||||
|
||||
## OSD Support
|
||||
|
||||
The MambaH743v4 supports OSD using OSD_TYPE 1 (MAX7456 driver).
|
||||
|
||||
## PWM Output
|
||||
|
||||
The MambaH743v4 supports up to 9 PWM outputs. The pads for motor output
|
||||
M1 to M8 are provided on both the motor connectors and on separate pads, plus
|
||||
M9 on a separate pad for LED strip or another PWM output.
|
||||
|
||||
The PWM is in 4 groups:
|
||||
|
||||
- PWM 1-4 in group1
|
||||
- PWM 5,6 in group2
|
||||
- PWM 7,8 in group3
|
||||
- PWM 9 in group4
|
||||
|
||||
Channels within the same group need to use the same output rate. If
|
||||
any channel in a group uses DShot then all channels in the group need
|
||||
to use DShot. Channels 1-8 support bi-directional dshot.
|
||||
|
||||
## Battery Monitoring
|
||||
|
||||
The board has a builting voltage and current sensor. The current
|
||||
sensor can read up to 130 Amps. The voltage sensor can handle up to 6S
|
||||
LiPo batteries.
|
||||
|
||||
The correct battery setting parameters are:
|
||||
|
||||
- BATT_MONITOR 4
|
||||
- BATT_VOLT_PIN 11
|
||||
- BATT_CURR_PIN 13
|
||||
- BATT_VOLT_MULT 11.1
|
||||
- BATT_AMP_PERVLT 64
|
||||
|
||||
## Compass
|
||||
|
||||
The MambaH743v4 does not have a builtin compass, but you can attach an external compass using I2C on the SDA and SCL pads.
|
||||
|
||||
## Loading Firmware
|
||||
|
||||
Initial firmware load can be done with DFU by plugging in USB with the
|
||||
bootloader button pressed. Then you should load the "with_bl.hex"
|
||||
firmware, using your favourite DFU loading tool.
|
||||
|
||||
Once the initial firmware is loaded you can update the firmware using
|
||||
any ArduPilot ground station software. Updates should be done with the
|
||||
*.apj firmware files.
|
||||
|
|
@ -0,0 +1,3 @@
|
|||
# setup for LEDs on chan9
|
||||
SERVO9_FUNCTION 120
|
||||
NTF_LED_TYPES 257
|
|
@ -0,0 +1,45 @@
|
|||
# hw definition file for processing by chibios_pins.py
|
||||
# for Diatone MambaH743 mk4 bootloader
|
||||
|
||||
# MCU class and specific type
|
||||
MCU STM32H7xx STM32H743xx
|
||||
|
||||
# board ID for firmware load
|
||||
APJ_BOARD_ID 1073
|
||||
|
||||
# crystal frequency, setup to use external oscillator
|
||||
OSCILLATOR_HZ 8000000
|
||||
|
||||
FLASH_SIZE_KB 2048
|
||||
|
||||
# bootloader starts at zero offset
|
||||
FLASH_RESERVE_START_KB 0
|
||||
|
||||
# the location where the bootloader will put the firmware
|
||||
FLASH_BOOTLOADER_LOAD_KB 384
|
||||
|
||||
STORAGE_FLASH_PAGE 1
|
||||
|
||||
# order of UARTs (and USB)
|
||||
SERIAL_ORDER OTG1
|
||||
|
||||
# PA10 IO-debug-console
|
||||
PA11 OTG_FS_DM OTG1
|
||||
PA12 OTG_FS_DP OTG1
|
||||
|
||||
PA13 JTMS-SWDIO SWD
|
||||
PA14 JTCK-SWCLK SWD
|
||||
|
||||
PE3 BUZZER OUTPUT LOW PULLDOWN
|
||||
|
||||
PE5 LED_BOOTLOADER OUTPUT LOW
|
||||
define HAL_LED_ON 1
|
||||
|
||||
# default to all pins low to avoid ESD issues
|
||||
DEFAULTGPIO OUTPUT LOW PULLDOWN
|
||||
|
||||
# Add CS pins to ensure they are high in bootloader
|
||||
PA15 FLASH_CS CS
|
||||
PB12 MAX7456_CS CS
|
||||
PA4 MPU6000_CS CS
|
||||
PE11 MPU6000_2_CS CS
|
|
@ -0,0 +1,187 @@
|
|||
# hw definition file for processing by chibios_pins.py
|
||||
# for Diatone MambaH743 mk4 hardware.
|
||||
|
||||
# MCU class and specific type
|
||||
MCU STM32H7xx STM32H743xx
|
||||
|
||||
# board ID for firmware load
|
||||
APJ_BOARD_ID 1073
|
||||
|
||||
# crystal frequency, setup to use external oscillator
|
||||
OSCILLATOR_HZ 8000000
|
||||
|
||||
MCU_CLOCKRATE_MHZ 480
|
||||
|
||||
FLASH_SIZE_KB 2048
|
||||
|
||||
# ChibiOS system timer
|
||||
STM32_ST_USE_TIMER 12
|
||||
define CH_CFG_ST_RESOLUTION 16
|
||||
|
||||
# leave 1 sectors free
|
||||
FLASH_RESERVE_START_KB 384
|
||||
|
||||
# use last 2 pages for flash storage
|
||||
# H743 has 16 pages of 128k each
|
||||
STORAGE_FLASH_PAGE 1
|
||||
define HAL_STORAGE_SIZE 32768
|
||||
|
||||
# enable logging to dataflash
|
||||
define HAL_LOGGING_DATAFLASH_ENABLED 1
|
||||
|
||||
# one I2C bus
|
||||
I2C_ORDER I2C1 I2C2
|
||||
|
||||
# order of UARTs (and USB)
|
||||
SERIAL_ORDER OTG1 USART1 USART2 USART3 UART4 UART5 USART6 UART7 UART8
|
||||
|
||||
# buzzer
|
||||
PE3 BUZZER OUTPUT LOW PULLDOWN GPIO(80)
|
||||
define HAL_BUZZER_PIN 80
|
||||
define HAL_BUZZER_ON 1
|
||||
define HAL_BUZZER_OFF 0
|
||||
define HAL_PWM_ALT_ALARM
|
||||
|
||||
# PA10 IO-debug-console
|
||||
PA11 OTG_FS_DM OTG1
|
||||
PA12 OTG_FS_DP OTG1
|
||||
|
||||
PA13 JTMS-SWDIO SWD
|
||||
PA14 JTCK-SWCLK SWD
|
||||
|
||||
# SPI1 for BMI270 / MPU6000
|
||||
PA4 MPU6000_CS CS
|
||||
PA5 SPI1_SCK SPI1
|
||||
PA6 SPI1_MISO SPI1
|
||||
PA7 SPI1_MOSI SPI1
|
||||
|
||||
# SPI2 for MAX7456 OSD
|
||||
PB12 MAX7456_CS CS
|
||||
PB13 SPI2_SCK SPI2
|
||||
PB14 SPI2_MISO SPI2
|
||||
PB15 SPI2_MOSI SPI2
|
||||
|
||||
# SPI3 for flash
|
||||
PA15 FLASH_CS CS
|
||||
PC10 SPI3_SCK SPI3
|
||||
PC11 SPI3_MISO SPI3
|
||||
PB2 SPI3_MOSI SPI3
|
||||
|
||||
# SPI4 for MPU6000_2
|
||||
PE11 MPU6000_2_CS CS
|
||||
PE12 SPI4_SCK SPI4
|
||||
PE13 SPI4_MISO SPI4
|
||||
PE14 SPI4_MOSI SPI4
|
||||
|
||||
# I2C1 for baro
|
||||
PB6 I2C1_SCL I2C1
|
||||
PB7 I2C1_SDA I2C1
|
||||
|
||||
# I2C2 for baro
|
||||
PB10 I2C2_SCL I2C2
|
||||
PB11 I2C2_SDA I2C2
|
||||
|
||||
PC1 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
||||
PC3 BATT_CURRENT_SENS ADC1 SCALE(1)
|
||||
|
||||
# define default battery setup
|
||||
define HAL_BATT_MONITOR_DEFAULT 4
|
||||
define HAL_BATT_VOLT_PIN 11
|
||||
define HAL_BATT_CURR_PIN 13
|
||||
define HAL_BATT_VOLT_SCALE 11.1
|
||||
define HAL_BATT_CURR_SCALE 64
|
||||
|
||||
PC2 RSSI_ADC ADC1
|
||||
define BOARD_RSSI_ANA_PIN 12
|
||||
|
||||
PE5 LED0 OUTPUT LOW GPIO(90) # blue
|
||||
PE4 LED1 OUTPUT LOW GPIO(91) # orange
|
||||
define HAL_GPIO_A_LED_PIN 91
|
||||
define HAL_GPIO_B_LED_PIN 90
|
||||
define HAL_GPIO_LED_OFF 1
|
||||
|
||||
# USART1 (RX / SBUS)
|
||||
PA9 USART1_TX USART1
|
||||
PA10 USART1_RX USART1
|
||||
|
||||
# USART2
|
||||
PD5 USART2_TX USART2 NODMA
|
||||
PD6 USART2_RX USART2 NODMA
|
||||
|
||||
# USART3 (VTX)
|
||||
PD8 USART3_TX USART3 NODMA
|
||||
PD9 USART3_RX USART3 NODMA
|
||||
|
||||
# UART4 (GPS)
|
||||
PD1 UART4_TX UART4
|
||||
PD0 UART4_RX UART4
|
||||
|
||||
# UART5 (SPORT)
|
||||
PC12 UART5_TX UART5 NODMA
|
||||
PD2 UART5_RX UART5 NODMA
|
||||
|
||||
# USART6 (ESC Telemetry)
|
||||
PC6 USART6_TX USART6 NODMA
|
||||
PC7 USART6_RX USART6 NODMA
|
||||
|
||||
# UART7 (GPS)
|
||||
PE8 UART7_TX UART7
|
||||
PE7 UART7_RX UART7
|
||||
|
||||
PE1 UART8_TX UART8 NODMA
|
||||
PE0 UART8_RX UART8 NODMA
|
||||
|
||||
define HAL_SERIAL1_PROTOCOL SerialProtocol_RCIN
|
||||
define HAL_SERIAL1_BAUD 115
|
||||
define HAL_SERIAL6_PROTOCOL SerialProtocol_ESCTelemetry
|
||||
define HAL_SERIAL6_BAUD 115
|
||||
|
||||
# Motors
|
||||
PA0 TIM5_CH1 TIM5 PWM(1) GPIO(50) BIDIR
|
||||
PA1 TIM5_CH2 TIM5 PWM(2) GPIO(51)
|
||||
PA2 TIM5_CH3 TIM5 PWM(3) GPIO(52) BIDIR
|
||||
PA3 TIM5_CH4 TIM5 PWM(4) GPIO(53)
|
||||
PB0 TIM3_CH3 TIM3 PWM(5) GPIO(54) BIDIR
|
||||
PB1 TIM3_CH4 TIM3 PWM(6) GPIO(55)
|
||||
PC8 TIM8_CH3 TIM8 PWM(7) GPIO(56) BIDIR
|
||||
PC9 TIM8_CH4 TIM8 PWM(8) GPIO(57)
|
||||
|
||||
# Motor order implies Betaflight/X for standard ESCs
|
||||
define HAL_FRAME_TYPE_DEFAULT 12
|
||||
|
||||
# LED strip
|
||||
PA8 TIM1_CH1 TIM1 PWM(9) GPIO(58)
|
||||
|
||||
DMA_NOSHARE SPI3* SPI1*
|
||||
|
||||
# spi devices
|
||||
SPIDEV mpu6000 SPI1 DEVID1 MPU6000_CS MODE3 1*MHZ 4*MHZ
|
||||
SPIDEV bmi270 SPI1 DEVID2 MPU6000_CS MODE3 1*MHZ 4*MHZ
|
||||
SPIDEV mpu6000_2 SPI4 DEVID4 MPU6000_2_CS MODE3 1*MHZ 4*MHZ
|
||||
SPIDEV dataflash SPI3 DEVID1 FLASH_CS MODE3 104*MHZ 104*MHZ
|
||||
SPIDEV osd SPI2 DEVID4 MAX7456_CS MODE0 10*MHZ 10*MHZ
|
||||
|
||||
# no built-in compass, but probe the i2c bus for all possible
|
||||
# external compass types
|
||||
define ALLOW_ARM_NO_COMPASS
|
||||
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
||||
define HAL_I2C_INTERNAL_MASK 0
|
||||
define HAL_COMPASS_AUTO_ROT_DEFAULT 2
|
||||
define HAL_DEFAULT_INS_FAST_SAMPLE 3
|
||||
|
||||
# Two MPU6000s or one BMI270
|
||||
IMU Invensense SPI:mpu6000 ROTATION_YAW_90
|
||||
IMU Invensense SPI:mpu6000_2 ROTATION_YAW_180
|
||||
IMU BMI270 SPI:bmi270 ROTATION_PITCH_180
|
||||
|
||||
define HAL_LOGGING_DATAFLASH_DRIVER AP_Logger_W25N01GV
|
||||
|
||||
# one BARO
|
||||
BARO DPS280 I2C:0:0x76
|
||||
|
||||
# setup for OSD
|
||||
define OSD_ENABLED 1
|
||||
define HAL_OSD_TYPE_DEFAULT 1
|
||||
ROMFS_WILDCARD libraries/AP_OSD/fonts/font*.bin
|
||||
|
||||
define STM32_PWM_USE_ADVANCED TRUE
|
Loading…
Reference in New Issue