mirror of
https://github.com/ArduPilot/ardupilot
synced 2025-01-11 02:18:29 -04:00
ArduPPM: Experimental PPM encoder to test possible fail-safe detection improvements.
This commit is contained in:
John Arne Birkeland
parent
386ef45fbb
commit
222c9cfca3
866
Tools/ArduPPM/WorkBasket/Experimental/PPM_Encoder.h
Normal file
866
Tools/ArduPPM/WorkBasket/Experimental/PPM_Encoder.h
Normal file
@ -0,0 +1,866 @@
|
||||
// !!!!!!!!!! EXPERIMENTAL TEST VERSION - USE WITH CAUTION - DO NOT RELEASE PUBLIC FIRMWARE !!!!!!!!!!
|
||||
|
||||
// -------------------------------------------------------------
|
||||
// PPM ENCODER V2.3.11
|
||||
// -------------------------------------------------------------
|
||||
// Improved servo to ppm for ArduPilot MEGA v1.x (ATmega328p),
|
||||
// PhoneDrone and APM2 (ATmega32u2)
|
||||
|
||||
// By: John Arne Birkeland - 2012
|
||||
// APM v1.x adaptation and "difficult" receiver testing by Olivier ADLER
|
||||
// -------------------------------------------------------------
|
||||
// Changelog:
|
||||
|
||||
// 01-08-2011
|
||||
// V2.2.3 - Changed back to BLOCKING interrupts.
|
||||
// Assembly PPM compare interrupt can be switch back to non-blocking, but not recommended.
|
||||
// V2.2.3 - Implemented 0.5us cut filter to remove servo input capture jitter.
|
||||
|
||||
// 04-08-2011
|
||||
// V2.2.4 - Implemented PPM passtrough funtion.
|
||||
// Shorting channel 2&3 enabled ppm passtrough on channel 1.
|
||||
|
||||
// 04-08-2011
|
||||
// V2.2.5 - Implemented simple average filter to smooth servo input capture jitter.
|
||||
// Takes fewer clocks to execute and has better performance then cut filter.
|
||||
|
||||
// 05-08-2011
|
||||
// V2.2.51 - Minor bug fixes.
|
||||
|
||||
// 06-08-2011
|
||||
// V2.2.6 - PPM passtrough failsafe implemented.
|
||||
// The PPM generator will be activated and output failsafe values while ppm passtrough signal is missing.
|
||||
|
||||
// 01-09-2011
|
||||
// V2.2.61 - Temporary MUX pin always high patch for APM beta board
|
||||
|
||||
// 22-09-2011
|
||||
// V2.2.62 - ATmegaXXU2 USB connection status pin (PC2) for APM UART MUX selection (removed temporary high patch)
|
||||
// - Removed assembly optimized PPM generator (not usable for production release)
|
||||
|
||||
// 23-09-2011
|
||||
// V2.2.63 - Average filter disabled
|
||||
|
||||
// 24-09-2011
|
||||
// V2.2.64 - Added distincts Power on / Failsafe PPM values
|
||||
// - Changed CH5 (mode selection) PPM Power on and Failsafe values to 1555 (Flight mode 4)
|
||||
// - Added brownout detection : Failsafe values are copied after a brownout reset instead of power on values
|
||||
|
||||
// 25-09-2011
|
||||
// V2.2.65 - Implemented PPM output delay until input signal is detected (PWM and PPM pass-trough mode)
|
||||
// - Changed brownout detection and FailSafe handling to work with XXU2 chips
|
||||
// - Minor variable and define naming changes to enhance readability
|
||||
|
||||
// 15-03-2012
|
||||
// V2.2.66 - Added APM2 (ATmega32U2) support for using TX and RX status leds to indicate PWM and PPM traffic
|
||||
// - <RX>: <OFF> = no pwm input detected, <TOGGLE> = speed of toggle indicate how many channel are active, <ON> = input lost (failsafe)
|
||||
// - <TX>: <OFF> = ppm output not started, <FAST TOGGLE> = normal PWM->PPM output or PPM passtrough failsafe, <SLOW TOGGLE> = PPM passtrough
|
||||
|
||||
// 03-06-2012
|
||||
// V2.2.67 - Implemented detection and failsafe (throttle = 900us) for missing throttle signal.
|
||||
|
||||
// 04-06-2012
|
||||
// V2.2.68 - Fixed possible logic flaw in throttle failsafe reset if _JITTER_FILTER_ is enabled
|
||||
|
||||
// 02-11-2012
|
||||
// V2.2.69 - Added PPM output positive polarity - mainly for standalone PPM encoder board use
|
||||
|
||||
// 03-11-2012
|
||||
// V2.3.0 - Implemented single channel fail-safe detection for all inputs
|
||||
|
||||
// 16-11-2012
|
||||
// V2.3.1 - Improved watchdog timer reset, so that only valid input signals will prevent the watchdog timer from triggering
|
||||
|
||||
// 22-11-2012
|
||||
// V2.3.11 - Very experimental test forcing throttle fail-safe (RTL) on single channel loss. !DO NOT RELEASE TO PUBLIC!
|
||||
|
||||
// -------------------------------------------------------------
|
||||
|
||||
#ifndef _PPM_ENCODER_H_
|
||||
#define _PPM_ENCODER_H_
|
||||
|
||||
#include <avr/io.h>
|
||||
|
||||
// -------------------------------------------------------------
|
||||
|
||||
#include <avr/interrupt.h>
|
||||
#include <avr/wdt.h>
|
||||
#include <util/delay.h>
|
||||
|
||||
|
||||
// -------------------------------------------------------------
|
||||
// SERVO INPUT FILTERS
|
||||
// -------------------------------------------------------------
|
||||
// Using both filters is not recommended and may reduce servo input resolution
|
||||
|
||||
// #define _AVERAGE_FILTER_ // Average filter to smooth servo input capture jitter
|
||||
// #define _JITTER_FILTER_ // Cut filter to remove 0,5us servo input capture jitter
|
||||
// -------------------------------------------------------------
|
||||
|
||||
#ifndef F_CPU
|
||||
#define F_CPU 16000000UL
|
||||
#endif
|
||||
|
||||
#ifndef true
|
||||
#define true 1
|
||||
#endif
|
||||
|
||||
#ifndef false
|
||||
#define false 0
|
||||
#endif
|
||||
|
||||
#ifndef bool
|
||||
#define bool _Bool
|
||||
#endif
|
||||
|
||||
// Version stamp for firmware hex file ( decode hex file using <avr-objdump -s file.hex> and look for "ArduPPM" string )
|
||||
const char ver[15] = "ArduPPMv2.3.11";
|
||||
|
||||
// -------------------------------------------------------------
|
||||
// INPUT MODE
|
||||
// -------------------------------------------------------------
|
||||
|
||||
#define JUMPER_SELECT_MODE 0 // Default - PPM passtrough mode selected if channel 2&3 shorted. Normal servo input (pwm) if not shorted.
|
||||
#define SERVO_PWM_MODE 1 // Normal 8 channel servo (pwm) input
|
||||
#define PPM_PASSTROUGH_MODE 2 // PPM signal passtrough on channel 1
|
||||
#define JETI_MODE 3 // Reserved
|
||||
#define SPEKTRUM_MODE 4 // Reserved for Spektrum satelitte on channel 1
|
||||
|
||||
// Servo input mode (jumper (default), pwm, ppm, jeti or spektrum)
|
||||
volatile uint8_t servo_input_mode = JUMPER_SELECT_MODE;
|
||||
// -------------------------------------------------------------
|
||||
|
||||
// Number of Timer1 ticks in one microsecond
|
||||
#define ONE_US F_CPU / 8 / 1000 / 1000
|
||||
|
||||
// 400us PPM pre pulse
|
||||
#define PPM_PRE_PULSE ONE_US * 400
|
||||
|
||||
|
||||
// -------------------------------------------------------------
|
||||
// SERVO LIMIT VALUES
|
||||
// -------------------------------------------------------------
|
||||
|
||||
// Servo minimum position
|
||||
#define PPM_SERVO_MIN ONE_US * 900 - PPM_PRE_PULSE
|
||||
|
||||
// Servo center position
|
||||
#define PPM_SERVO_CENTER ONE_US * 1500 - PPM_PRE_PULSE
|
||||
|
||||
// Servo maximum position
|
||||
#define PPM_SERVO_MAX ONE_US * 2100 - PPM_PRE_PULSE
|
||||
|
||||
// Throttle default at power on
|
||||
#define PPM_THROTTLE_DEFAULT ONE_US * 1100 - PPM_PRE_PULSE
|
||||
|
||||
// Throttle during failsafe
|
||||
#define PPM_THROTTLE_FAILSAFE ONE_US * 900 - PPM_PRE_PULSE
|
||||
|
||||
// CH5 power on values (mode selection channel)
|
||||
#define PPM_CH5_MODE_4 ONE_US * 1555 - PPM_PRE_PULSE
|
||||
|
||||
// -------------------------------------------------------------
|
||||
// PPM OUTPUT SETTINGS
|
||||
// -------------------------------------------------------------
|
||||
// #define _POSITIVE_PPM_FRAME_ // Switch to positive pulse PPM
|
||||
// (the actual timing is encoded in the length of the low between two pulses)
|
||||
|
||||
// Number of servo input channels
|
||||
#define SERVO_CHANNELS 8
|
||||
|
||||
// PPM period 18.5ms - 26.5ms (54hz - 37Hz)
|
||||
#define PPM_PERIOD ONE_US * ( 22500 - ( 8 * 1500 ) )
|
||||
|
||||
// Size of ppm[..] data array ( servo channels * 2 + 2)
|
||||
#define PPM_ARRAY_MAX 18
|
||||
|
||||
// -------------------------------------------------------------
|
||||
// SERVO FAILSAFE VALUES
|
||||
// -------------------------------------------------------------
|
||||
const uint16_t failsafe_ppm[ PPM_ARRAY_MAX ] =
|
||||
{
|
||||
PPM_PRE_PULSE,
|
||||
PPM_SERVO_CENTER, // Channel 1
|
||||
PPM_PRE_PULSE,
|
||||
PPM_SERVO_CENTER, // Channel 2
|
||||
PPM_PRE_PULSE,
|
||||
PPM_THROTTLE_FAILSAFE, // Channel 3 (throttle)
|
||||
PPM_PRE_PULSE,
|
||||
PPM_SERVO_CENTER, // Channel 4
|
||||
PPM_PRE_PULSE,
|
||||
PPM_CH5_MODE_4, // Channel 5
|
||||
PPM_PRE_PULSE,
|
||||
PPM_SERVO_CENTER, // Channel 6
|
||||
PPM_PRE_PULSE,
|
||||
PPM_SERVO_CENTER, // Channel 7
|
||||
PPM_PRE_PULSE,
|
||||
PPM_SERVO_CENTER, // Channel 8
|
||||
PPM_PRE_PULSE,
|
||||
PPM_PERIOD
|
||||
};
|
||||
|
||||
// -------------------------------------------------------------
|
||||
// Data array for storing ppm (8 channels) pulse widths.
|
||||
// -------------------------------------------------------------
|
||||
volatile uint16_t ppm[ PPM_ARRAY_MAX ] =
|
||||
{
|
||||
PPM_PRE_PULSE,
|
||||
PPM_SERVO_CENTER, // Channel 1
|
||||
PPM_PRE_PULSE,
|
||||
PPM_SERVO_CENTER, // Channel 2
|
||||
PPM_PRE_PULSE,
|
||||
PPM_THROTTLE_DEFAULT, // Channel 3 (throttle)
|
||||
PPM_PRE_PULSE,
|
||||
PPM_SERVO_CENTER, // Channel 4
|
||||
PPM_PRE_PULSE,
|
||||
PPM_CH5_MODE_4, // Channel 5
|
||||
PPM_PRE_PULSE,
|
||||
PPM_SERVO_CENTER, // Channel 6
|
||||
PPM_PRE_PULSE,
|
||||
PPM_SERVO_CENTER, // Channel 7
|
||||
PPM_PRE_PULSE,
|
||||
PPM_SERVO_CENTER, // Channel 8
|
||||
PPM_PRE_PULSE,
|
||||
PPM_PERIOD
|
||||
};
|
||||
|
||||
// -------------------------------------------------------------
|
||||
// Data arraw for storing ppm timeout (missing channel detection)
|
||||
// -------------------------------------------------------------
|
||||
#define PPM_TIMEOUT_VALUE 40 // ~1sec before triggering missing channel detection
|
||||
volatile uint8_t ppm_timeout[ PPM_ARRAY_MAX ];
|
||||
|
||||
// Servo input channel connected flag
|
||||
volatile bool servo_input_connected[ PPM_ARRAY_MAX ];
|
||||
|
||||
// AVR parameters for PhoneDrone and APM2 boards using ATmega32u2
|
||||
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
||||
|
||||
#define SERVO_DDR DDRB
|
||||
#define SERVO_PORT PORTB
|
||||
#define SERVO_INPUT PINB
|
||||
#define SERVO_INT_VECTOR PCINT0_vect
|
||||
#define SERVO_INT_MASK PCMSK0
|
||||
#define SERVO_INT_CLEAR_FLAG PCIF0
|
||||
#define SERVO_INT_ENABLE PCIE0
|
||||
#define SERVO_TIMER_CNT TCNT1
|
||||
|
||||
#define PPM_DDR DDRC
|
||||
#define PPM_PORT PORTC
|
||||
#define PPM_OUTPUT_PIN PC6
|
||||
#define PPM_INT_VECTOR TIMER1_COMPA_vect
|
||||
#define PPM_COMPARE OCR1A
|
||||
#define PPM_COMPARE_FLAG COM1A0
|
||||
#define PPM_COMPARE_ENABLE OCIE1A
|
||||
#define PPM_COMPARE_FORCE_MATCH FOC1A
|
||||
|
||||
#define USB_DDR DDRC
|
||||
#define USB_PORT PORTC
|
||||
#define USB_PIN PC2
|
||||
|
||||
// true if we have received a USB device connect event
|
||||
static bool usb_connected;
|
||||
|
||||
// USB connected event
|
||||
void EVENT_USB_Device_Connect(void)
|
||||
{
|
||||
// Toggle USB pin high if USB is connected
|
||||
USB_PORT |= (1 << USB_PIN);
|
||||
|
||||
usb_connected = true;
|
||||
|
||||
// this unsets the pin connected to PA1 on the 2560
|
||||
// when the bit is clear, USB is connected
|
||||
PORTD &= ~1;
|
||||
}
|
||||
|
||||
// USB disconnect event
|
||||
void EVENT_USB_Device_Disconnect(void)
|
||||
{
|
||||
// toggle USB pin low if USB is disconnected
|
||||
USB_PORT &= ~(1 << USB_PIN);
|
||||
|
||||
usb_connected = false;
|
||||
|
||||
// this sets the pin connected to PA1 on the 2560
|
||||
// when the bit is clear, USB is connected
|
||||
PORTD |= 1;
|
||||
}
|
||||
|
||||
// AVR parameters for ArduPilot MEGA v1.4 PPM Encoder (ATmega328P)
|
||||
#elif defined (__AVR_ATmega328P__) || defined (__AVR_ATmega328__)
|
||||
|
||||
#define SERVO_DDR DDRD
|
||||
#define SERVO_PORT PORTD
|
||||
#define SERVO_INPUT PIND
|
||||
#define SERVO_INT_VECTOR PCINT2_vect
|
||||
#define SERVO_INT_MASK PCMSK2
|
||||
#define SERVO_INT_CLEAR_FLAG PCIF2
|
||||
#define SERVO_INT_ENABLE PCIE2
|
||||
#define SERVO_TIMER_CNT TCNT1
|
||||
|
||||
#define PPM_DDR DDRB
|
||||
#define PPM_PORT PORTB
|
||||
#define PPM_OUTPUT_PIN PB2
|
||||
#define PPM_INT_VECTOR TIMER1_COMPB_vect
|
||||
#define PPM_COMPARE OCR1B
|
||||
#define PPM_COMPARE_FLAG COM1B0
|
||||
#define PPM_COMPARE_ENABLE OCIE1B
|
||||
#define PPM_COMPARE_FORCE_MATCH FOC1B
|
||||
|
||||
#else
|
||||
#error NO SUPPORTED DEVICE FOUND! (ATmega16u2 / ATmega32u2 / ATmega328p)
|
||||
#endif
|
||||
|
||||
// Used to force throttle fail-safe mode (RTL)
|
||||
volatile bool throttle_failsafe_force = false;
|
||||
|
||||
// Used to indicate invalid SERVO input signals
|
||||
volatile uint8_t servo_input_errors = 0;
|
||||
|
||||
// Used to indicate missing SERVO input signals
|
||||
volatile bool servo_input_missing = true;
|
||||
|
||||
// Used to indicate if PPM generator is active
|
||||
volatile bool ppm_generator_active = false;
|
||||
|
||||
// Used to indicate a brownout restart
|
||||
volatile bool brownout_reset = false;
|
||||
|
||||
|
||||
// ------------------------------------------------------------------------------
|
||||
// PPM GENERATOR START - TOGGLE ON COMPARE INTERRUPT ENABLE
|
||||
// ------------------------------------------------------------------------------
|
||||
void ppm_start( void )
|
||||
{
|
||||
// Prevent reenabling an already active PPM generator
|
||||
if( ppm_generator_active ) return;
|
||||
|
||||
// Store interrupt status and register flags
|
||||
uint8_t SREG_tmp = SREG;
|
||||
|
||||
// Stop interrupts
|
||||
cli();
|
||||
|
||||
// Make sure initial output state is low
|
||||
PPM_PORT &= ~(1 << PPM_OUTPUT_PIN);
|
||||
|
||||
// Wait for output pin to settle
|
||||
//_delay_us( 1 );
|
||||
|
||||
// Set initial compare toggle to maximum (32ms) to give other parts of the system time to start
|
||||
SERVO_TIMER_CNT = 0;
|
||||
PPM_COMPARE = 0xFFFF;
|
||||
|
||||
// Set toggle on compare output
|
||||
TCCR1A = (1 << PPM_COMPARE_FLAG);
|
||||
|
||||
// Set TIMER1 8x prescaler
|
||||
TCCR1B = ( 1 << CS11 );
|
||||
|
||||
#if defined (_POSITIVE_PPM_FRAME_)
|
||||
// Force output compare to reverse polarity
|
||||
TCCR1C |= (1 << PPM_COMPARE_FORCE_MATCH);
|
||||
#endif
|
||||
|
||||
// Enable output compare interrupt
|
||||
TIMSK1 |= (1 << PPM_COMPARE_ENABLE);
|
||||
|
||||
// Indicate that PPM generator is active
|
||||
ppm_generator_active = true;
|
||||
|
||||
// Restore interrupt status and register flags
|
||||
SREG = SREG_tmp;
|
||||
|
||||
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
||||
// Turn on TX led if PPM generator is active
|
||||
PORTD &= ~( 1<< PD5 );
|
||||
#endif
|
||||
}
|
||||
|
||||
// ------------------------------------------------------------------------------
|
||||
// PPM GENERATOR STOP - TOGGLE ON COMPARE INTERRUPT DISABLE
|
||||
// ------------------------------------------------------------------------------
|
||||
void ppm_stop( void )
|
||||
{
|
||||
// Store interrupt status and register flags
|
||||
uint8_t SREG_tmp = SREG;
|
||||
|
||||
// Stop interrupts
|
||||
cli();
|
||||
|
||||
// Disable output compare interrupt
|
||||
TIMSK1 &= ~(1 << PPM_COMPARE_ENABLE);
|
||||
|
||||
// Reset TIMER1 registers
|
||||
TCCR1A = 0;
|
||||
TCCR1B = 0;
|
||||
|
||||
// Indicate that PPM generator is not active
|
||||
ppm_generator_active = false;
|
||||
|
||||
// Restore interrupt status and register flags
|
||||
SREG = SREG_tmp;
|
||||
|
||||
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
||||
// Turn off TX led if PPM generator is off
|
||||
PORTD |= ( 1<< PD5 );
|
||||
#endif
|
||||
}
|
||||
|
||||
// ------------------------------------------------------------------------------
|
||||
// Watchdog Interrupt (interrupt only mode, no reset)
|
||||
// ------------------------------------------------------------------------------
|
||||
ISR( WDT_vect ) // If watchdog is triggered then enable missing signal flag and copy power on or failsafe positions
|
||||
{
|
||||
// Use failsafe values if PPM generator is active or if chip has been reset from a brown-out
|
||||
if ( ppm_generator_active || brownout_reset )
|
||||
{
|
||||
// Copy failsafe values to ppm[..]
|
||||
for ( uint8_t i = 0; i < PPM_ARRAY_MAX; i++ )
|
||||
{
|
||||
ppm[ i ] = failsafe_ppm[ i ];
|
||||
}
|
||||
|
||||
}
|
||||
|
||||
// If we are in PPM passtrough mode and a input signal has been detected, or if chip has been reset from a brown_out then start the PPM generator.
|
||||
if( ( servo_input_mode == PPM_PASSTROUGH_MODE && servo_input_missing == false ) || brownout_reset )
|
||||
{
|
||||
// Start PPM generator
|
||||
ppm_start();
|
||||
brownout_reset = false;
|
||||
}
|
||||
|
||||
// Set missing receiver signal flag
|
||||
servo_input_missing = true;
|
||||
|
||||
// Reset servo input error flag
|
||||
servo_input_errors = 0;
|
||||
|
||||
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
||||
// Turn on RX led if failsafe has triggered after ppm generator i active
|
||||
if( ppm_generator_active ) PORTD &= ~( 1<< PD4 );
|
||||
#endif
|
||||
}
|
||||
// ------------------------------------------------------------------------------
|
||||
|
||||
|
||||
// ------------------------------------------------------------------------------
|
||||
// SERVO/PPM INPUT - PIN CHANGE INTERRUPT
|
||||
// ------------------------------------------------------------------------------
|
||||
ISR( SERVO_INT_VECTOR )
|
||||
{
|
||||
// Servo pulse start timing
|
||||
//static uint16_t servo_start[ SERVO_CHANNELS ] = { 0, 0, 0, 0, 0, 0, 0, 0 };
|
||||
static uint16_t servo_start[ PPM_ARRAY_MAX ] = { 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0 }; // We sacrefice some memory but save instructions by working with ppm index count (18) instead of input channel count (8)
|
||||
|
||||
|
||||
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
||||
// Toggle LED delay
|
||||
static uint8_t led_delay = 0;
|
||||
#endif
|
||||
|
||||
// Servo input pin storage
|
||||
static uint8_t servo_pins_old = 0;
|
||||
|
||||
// Used to store current servo input pins
|
||||
uint8_t servo_pins;
|
||||
|
||||
// Read current servo pulse change time
|
||||
uint16_t servo_time = SERVO_TIMER_CNT;
|
||||
|
||||
// ------------------------------------------------------------------------------
|
||||
// PPM passtrough mode ( signal passtrough from channel 1 to ppm output pin)
|
||||
// ------------------------------------------------------------------------------
|
||||
if( servo_input_mode == PPM_PASSTROUGH_MODE )
|
||||
{
|
||||
// Has watchdog timer failsafe started PPM generator? If so we need to stop it.
|
||||
if( ppm_generator_active )
|
||||
{
|
||||
// Stop PPM generator
|
||||
ppm_stop();
|
||||
}
|
||||
|
||||
// PPM (channel 1) input pin is high
|
||||
if( SERVO_INPUT & 1 )
|
||||
{
|
||||
// Set PPM output pin high
|
||||
PPM_PORT |= (1 << PPM_OUTPUT_PIN);
|
||||
}
|
||||
// PPM (channel 1) input pin is low
|
||||
else
|
||||
{
|
||||
// Set PPM output pin low
|
||||
PPM_PORT &= ~(1 << PPM_OUTPUT_PIN);
|
||||
}
|
||||
|
||||
// Reset Watchdog Timer
|
||||
wdt_reset();
|
||||
|
||||
// Set servo input missing flag false to indicate that we have received servo input signals
|
||||
servo_input_missing = false;
|
||||
|
||||
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
||||
// Toggle TX LED at PPM passtrough
|
||||
if( ++led_delay > 128 ) // Toggle every 128th pulse
|
||||
{
|
||||
// Toggle TX led
|
||||
PIND |= ( 1<< PD5 );
|
||||
led_delay = 0;
|
||||
}
|
||||
#endif
|
||||
|
||||
// Leave interrupt
|
||||
return;
|
||||
}
|
||||
|
||||
// ------------------------------------------------------------------------------
|
||||
// SERVO PWM MODE
|
||||
// ------------------------------------------------------------------------------
|
||||
uint8_t servo_change;
|
||||
uint8_t servo_pin ;
|
||||
//uint8_t servo_channel ;
|
||||
uint8_t ppm_channel;
|
||||
|
||||
CHECK_PINS_START: // Start of servo input check
|
||||
|
||||
// Store current servo input pins
|
||||
servo_pins = SERVO_INPUT;
|
||||
|
||||
// Calculate servo input pin change mask
|
||||
servo_change = servo_pins ^ servo_pins_old;
|
||||
|
||||
// Set initial servo pin, channel and ppm[..] index
|
||||
servo_pin = 1;
|
||||
//servo_channel = 0;
|
||||
ppm_channel = 1;
|
||||
|
||||
CHECK_PINS_LOOP: // Input servo pin check loop
|
||||
|
||||
// Check for pin change on current servo channel
|
||||
if( servo_change & servo_pin )
|
||||
{
|
||||
// High (raising edge)
|
||||
if( servo_pins & servo_pin )
|
||||
{
|
||||
//servo_start[ servo_channel ] = servo_time;
|
||||
servo_start[ ppm_channel ] = servo_time;
|
||||
}
|
||||
else
|
||||
{
|
||||
|
||||
// Get servo pulse width
|
||||
//uint16_t servo_width = servo_time - servo_start[ servo_channel ] - PPM_PRE_PULSE;
|
||||
uint16_t servo_width = servo_time - servo_start[ ppm_channel ] - PPM_PRE_PULSE;
|
||||
|
||||
// Check that servo pulse signal is valid before sending to ppm encoder
|
||||
if( servo_width > PPM_SERVO_MAX ) goto CHECK_PINS_ERROR;
|
||||
if( servo_width < PPM_SERVO_MIN ) goto CHECK_PINS_ERROR;
|
||||
|
||||
// Reset Watchdog Timer
|
||||
wdt_reset();
|
||||
|
||||
// Channel has received a valid signal, so it must be connected
|
||||
servo_input_connected [ ppm_channel ] = true;
|
||||
|
||||
// Check for forced throttle fail-safe
|
||||
if( throttle_failsafe_force && ppm_channel == 5 )
|
||||
{
|
||||
// Force throttle fail-safe
|
||||
ppm_timeout[ ppm_channel ] = 255;
|
||||
}
|
||||
else
|
||||
{
|
||||
//Reset ppm single channel fail-safe timeout
|
||||
ppm_timeout[ ppm_channel ] = 0;
|
||||
}
|
||||
|
||||
#ifdef _AVERAGE_FILTER_
|
||||
// Average filter to smooth input jitter
|
||||
servo_width += ppm[ ppm_channel ];
|
||||
servo_width >>= 1;
|
||||
#endif
|
||||
|
||||
#ifdef _JITTER_FILTER_
|
||||
// 0.5us cut filter to remove input jitter
|
||||
int16_t ppm_tmp = ppm[ ppm_channel ] - servo_width;
|
||||
if( ppm_tmp == 1 ) goto CHECK_PINS_NEXT;
|
||||
if( ppm_tmp == -1 ) goto CHECK_PINS_NEXT;
|
||||
#endif
|
||||
|
||||
// Update ppm[..]
|
||||
ppm[ ppm_channel ] = servo_width;
|
||||
}
|
||||
}
|
||||
|
||||
CHECK_PINS_NEXT:
|
||||
|
||||
// Select next servo pin
|
||||
servo_pin <<= 1;
|
||||
|
||||
// Select next servo channel
|
||||
//servo_channel++;
|
||||
|
||||
// Select next ppm[..] index
|
||||
ppm_channel += 2;
|
||||
|
||||
// Check channel and process if needed
|
||||
//if( servo_channel < SERVO_CHANNELS ) goto CHECK_PINS_LOOP;
|
||||
if( servo_pin ) goto CHECK_PINS_LOOP; // Bitshift wraps to zero (false)
|
||||
|
||||
goto CHECK_PINS_DONE;
|
||||
|
||||
CHECK_PINS_ERROR:
|
||||
|
||||
// Used to indicate invalid servo input signals
|
||||
servo_input_errors++;
|
||||
|
||||
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
||||
// Delay LED toggle
|
||||
led_delay = 0;
|
||||
#endif
|
||||
|
||||
goto CHECK_PINS_NEXT;
|
||||
|
||||
// All servo input pins has now been processed
|
||||
|
||||
CHECK_PINS_DONE:
|
||||
|
||||
// Set servo input missing flag false to indicate that we have received servo input signals
|
||||
servo_input_missing = false;
|
||||
|
||||
// Store current servo input pins for next check
|
||||
servo_pins_old = servo_pins;
|
||||
|
||||
// Start PPM generator if not already running
|
||||
if( ppm_generator_active == false ) ppm_start();
|
||||
|
||||
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
||||
// Toggle RX LED when finished receiving servo pulses
|
||||
if( ++led_delay > 64 ) // Toggle led every 64th time
|
||||
{
|
||||
PIND |= ( 1<< PD4 );
|
||||
led_delay = 0;
|
||||
}
|
||||
#endif
|
||||
|
||||
//Has servo input changed while processing pins, if so we need to re-check pins
|
||||
if( servo_pins != SERVO_INPUT ) goto CHECK_PINS_START;
|
||||
|
||||
// Clear interrupt event from already processed pin changes
|
||||
PCIFR |= (1 << SERVO_INT_CLEAR_FLAG);
|
||||
}
|
||||
// ------------------------------------------------------------------------------
|
||||
|
||||
|
||||
// ------------------------------------------------------------------------------
|
||||
// PPM OUTPUT - TIMER1 COMPARE INTERRUPT
|
||||
// ------------------------------------------------------------------------------
|
||||
ISR( PPM_INT_VECTOR )
|
||||
{
|
||||
// Current active ppm channel
|
||||
static uint8_t ppm_channel = PPM_ARRAY_MAX - 1;
|
||||
|
||||
// Update timing for next compare toggle with either current ppm input value, or fail-safe value if there is a channel timeout.
|
||||
if( ppm_timeout[ ppm_channel ] > PPM_TIMEOUT_VALUE )
|
||||
{
|
||||
// Use ppm fail-safe value
|
||||
PPM_COMPARE += failsafe_ppm[ ppm_channel ];
|
||||
|
||||
// Did we lose an active servo input channel? If so force throttle fail-safe (RTL)
|
||||
if( servo_input_connected[ ppm_channel ] )
|
||||
{
|
||||
throttle_failsafe_force = true;
|
||||
}
|
||||
}
|
||||
else
|
||||
{
|
||||
// Use latest ppm input value
|
||||
PPM_COMPARE += ppm[ ppm_channel ];
|
||||
|
||||
// Increment channel timeout (reset to zero in input interrupt each time a valid signal is detected)
|
||||
ppm_timeout[ ppm_channel ] ++;
|
||||
}
|
||||
|
||||
// Select the next ppm channel
|
||||
if( ++ppm_channel >= PPM_ARRAY_MAX )
|
||||
{
|
||||
ppm_channel = 0;
|
||||
|
||||
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
||||
// Blink TX LED when PPM generator has finished a pulse train
|
||||
PIND |= ( 1<< PD5 );
|
||||
#endif
|
||||
}
|
||||
}
|
||||
// ------------------------------------------------------------------------------
|
||||
|
||||
// ------------------------------------------------------------------------------
|
||||
// PPM READ - INTERRUPT SAFE PPM SERVO CHANNEL READ
|
||||
// ------------------------------------------------------------------------------
|
||||
uint16_t ppm_read_channel( uint8_t channel )
|
||||
{
|
||||
// Limit channel to valid value
|
||||
uint8_t _channel = channel;
|
||||
if( _channel == 0 ) _channel = 1;
|
||||
if( _channel > SERVO_CHANNELS ) _channel = SERVO_CHANNELS;
|
||||
|
||||
// Calculate ppm[..] position
|
||||
uint8_t ppm_index = ( _channel << 1 ) + 1;
|
||||
|
||||
// Read ppm[..] in a non blocking interrupt safe manner
|
||||
uint16_t ppm_tmp = ppm[ ppm_index ];
|
||||
while( ppm_tmp != ppm[ ppm_index ] ) ppm_tmp = ppm[ ppm_index ];
|
||||
|
||||
// Return as normal servo value
|
||||
return ppm_tmp + PPM_PRE_PULSE;
|
||||
}
|
||||
// ------------------------------------------------------------------------------
|
||||
|
||||
// ------------------------------------------------------------------------------
|
||||
// PPM ENCODER INIT
|
||||
// ------------------------------------------------------------------------------
|
||||
void ppm_encoder_init( void )
|
||||
{
|
||||
// ATmegaXXU2 only init code
|
||||
// ------------------------------------------------------------------------------
|
||||
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
||||
// ------------------------------------------------------------------------------
|
||||
// Reset Source checkings
|
||||
// ------------------------------------------------------------------------------
|
||||
if (MCUSR & 1) // Power-on Reset
|
||||
{
|
||||
MCUSR=0; // Clear MCU Status register
|
||||
// custom code here
|
||||
}
|
||||
else if (MCUSR & 2) // External Reset
|
||||
{
|
||||
MCUSR=0; // Clear MCU Status register
|
||||
// custom code here
|
||||
}
|
||||
else if (MCUSR & 4) // Brown-Out Reset
|
||||
{
|
||||
MCUSR=0; // Clear MCU Status register
|
||||
brownout_reset=true;
|
||||
}
|
||||
else // Watchdog Reset
|
||||
{
|
||||
MCUSR=0; // Clear MCU Status register
|
||||
// custom code here
|
||||
}
|
||||
|
||||
// APM USB connection status UART MUX selector pin
|
||||
// ------------------------------------------------------------------------------
|
||||
USB_DDR |= (1 << USB_PIN); // Set USB pin to output
|
||||
#endif
|
||||
|
||||
|
||||
// USE JUMPER TO CHECK FOR PWM OR PPM PASSTROUGH MODE (channel 2&3 shorted)
|
||||
// ------------------------------------------------------------------------------
|
||||
if( servo_input_mode == JUMPER_SELECT_MODE )
|
||||
{
|
||||
// channel 3 status counter
|
||||
uint8_t channel3_status = 0;
|
||||
|
||||
// Set channel 3 to input
|
||||
SERVO_DDR &= ~(1 << 2);
|
||||
|
||||
// Enable channel 3 pullup
|
||||
SERVO_PORT |= (1 << 2);
|
||||
|
||||
// Set channel 2 to output
|
||||
SERVO_DDR |= (1 << 1);
|
||||
|
||||
// Set channel 2 output low
|
||||
SERVO_PORT &= ~(1 << 1);
|
||||
|
||||
_delay_us (10);
|
||||
|
||||
// Increment channel3_status if channel 3 is set low by channel 2
|
||||
if( ( SERVO_INPUT & (1 << 2) ) == 0 ) channel3_status++;
|
||||
|
||||
// Set channel 2 output high
|
||||
SERVO_PORT |= (1 << 1);
|
||||
|
||||
_delay_us (10);
|
||||
|
||||
// Increment channel3_status if channel 3 is set high by channel 2
|
||||
if( ( SERVO_INPUT & (1 << 2) ) != 0 ) channel3_status++;
|
||||
|
||||
// Set channel 2 output low
|
||||
SERVO_PORT &= ~(1 << 1);
|
||||
|
||||
_delay_us (10);
|
||||
|
||||
// Increment channel3_status if channel 3 is set low by channel 2
|
||||
if( ( SERVO_INPUT & (1 << 2) ) == 0 ) channel3_status++;
|
||||
|
||||
// Set servo input mode based on channel3_status
|
||||
if( channel3_status == 3 ) servo_input_mode = PPM_PASSTROUGH_MODE;
|
||||
else servo_input_mode = SERVO_PWM_MODE;
|
||||
|
||||
}
|
||||
|
||||
|
||||
// SERVO/PPM INPUT PINS
|
||||
// ------------------------------------------------------------------------------
|
||||
// Set all servo input pins to inputs
|
||||
SERVO_DDR = 0;
|
||||
|
||||
// Activate pullups on all input pins
|
||||
SERVO_PORT |= 0xFF;
|
||||
|
||||
#if defined (__AVR_ATmega16U2__) || defined (__AVR_ATmega32U2__)
|
||||
// on 32U2 set PD0 to be an output, and clear the bit. This tells
|
||||
// the 2560 that USB is connected. The USB connection event fires
|
||||
// later to set the right value
|
||||
DDRD |= 1;
|
||||
if (usb_connected) {
|
||||
PORTD &= ~1;
|
||||
} else {
|
||||
PORTD |= 1;
|
||||
}
|
||||
#endif
|
||||
|
||||
// SERVO/PPM INPUT - PIN CHANGE INTERRUPT
|
||||
// ------------------------------------------------------------------------------
|
||||
if( servo_input_mode == SERVO_PWM_MODE )
|
||||
{
|
||||
// Set servo input interrupt pin mask to all 8 servo input channels
|
||||
SERVO_INT_MASK = 0xFF;
|
||||
}
|
||||
|
||||
if( servo_input_mode == PPM_PASSTROUGH_MODE )
|
||||
{
|
||||
// Set servo input interrupt pin mask to servo input channel 1
|
||||
SERVO_INT_MASK = 0x01;
|
||||
}
|
||||
|
||||
// Enable servo input interrupt
|
||||
PCICR |= (1 << SERVO_INT_ENABLE);
|
||||
|
||||
// PPM OUTPUT PIN
|
||||
// ------------------------------------------------------------------------------
|
||||
// Set PPM pin to output
|
||||
PPM_DDR |= (1 << PPM_OUTPUT_PIN);
|
||||
|
||||
// ------------------------------------------------------------------------------
|
||||
// Enable watchdog interrupt mode
|
||||
// ------------------------------------------------------------------------------
|
||||
// Disable watchdog
|
||||
wdt_disable();
|
||||
// Reset watchdog timer
|
||||
wdt_reset();
|
||||
// Start timed watchdog setup sequence
|
||||
WDTCSR |= (1<<WDCE) | (1<<WDE );
|
||||
// Set 250 ms watchdog timeout and enable interrupt
|
||||
WDTCSR = (1<<WDIE) | (1<<WDP2);
|
||||
|
||||
|
||||
|
||||
}
|
||||
// ------------------------------------------------------------------------------
|
||||
|
||||
#endif // _PPM_ENCODER_H_
|
||||
|
||||
Loading…
Reference in New Issue
Block a user