mirror of https://github.com/ArduPilot/ardupilot
tridge: my config
git-svn-id: https://arducopter.googlecode.com/svn/trunk@1800 f9c3cf11-9bcb-44bc-f272-b75c42450872
This commit is contained in:
parent
ae9ae7f946
commit
216379e286
|
@ -1,28 +1,3 @@
|
|||
// Example config file. Use APM_Config.h.reference and the wiki to find additional defines to setup your plane.
|
||||
// Once you upload the code, run the factory "reset" to save all config values to EEPROM.
|
||||
// After reset, use the setup mode to set your radio limits for CH1-4, and to set your flight modes.
|
||||
|
||||
// GPS is auto-selected
|
||||
|
||||
#define GCS_PROTOCOL GCS_PROTOCOL_NONE
|
||||
|
||||
//#define MAG_ORIENTATION AP_COMPASS_COMPONENTS_UP_PINS_BACK
|
||||
|
||||
# define SERIAL0_BAUD 38400
|
||||
|
||||
//# define STABILIZE_ROLL_P 0.4
|
||||
//# define STABILIZE_PITCH_P 0.4
|
||||
//# define STABILIZE_DAMPENER 0.1
|
||||
|
||||
|
||||
//#define ACRO_RATE_TRIGGER 4200
|
||||
// if you want full ACRO mode, set value to 0
|
||||
// if you want safe ACRO mode, set value to 100
|
||||
// if you want mostly stabilize with flips, set value to 4200
|
||||
|
||||
|
||||
|
||||
// Logging
|
||||
//#define LOG_CURRENT ENABLED
|
||||
|
||||
// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: t -*-
|
||||
|
||||
#include "configs/tridge.h"
|
||||
|
|
|
@ -0,0 +1,49 @@
|
|||
// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: t -*-
|
||||
|
||||
// Example config file. Use APM_Config.h.reference and the wiki to find additional defines to setup your plane.
|
||||
// Once you upload the code, run the factory "reset" to save all config values to EEPROM.
|
||||
// After reset, use the setup mode to set your radio limits for CH1-4, and to set your flight modes.
|
||||
|
||||
// GPS is auto-selected
|
||||
|
||||
#define MAG_ORIENTATION AP_COMPASS_COMPONENTS_DOWN_PINS_FORWARD
|
||||
|
||||
#define SERIAL0_BAUD 115200
|
||||
#define SERIAL3_BAUD 115200
|
||||
|
||||
// Hardware in the loop protocol
|
||||
#if 0
|
||||
# define HIL_MODE HIL_MODE_NONE
|
||||
#else
|
||||
# define HIL_MODE HIL_MODE_ATTITUDE
|
||||
# define HIL_PROTOCOL HIL_PROTOCOL_MAVLINK
|
||||
# define HIL_PORT 0
|
||||
#endif
|
||||
|
||||
// You can set your gps protocol here for your actual
|
||||
// hardware and leave it without affecting the hardware
|
||||
// in the loop simulation
|
||||
|
||||
// Ground control station comms
|
||||
#define GCS_PROTOCOL GCS_PROTOCOL_MAVLINK
|
||||
#define GCS_PORT 0
|
||||
|
||||
//#define RADIO_OVERRIDE_DEFAULTS { 1500, 1500, 1000, 1500, 1000, 1000, 1000, 1815 }
|
||||
|
||||
#define FLIGHT_MODE_CHANNEL CH_8
|
||||
|
||||
#define FLIGHT_MODE_1 STABILIZE
|
||||
#define FLIGHT_MODE_2 ALT_HOLD
|
||||
#define FLIGHT_MODE_3 ACRO
|
||||
#define FLIGHT_MODE_4 STABILIZE
|
||||
#define FLIGHT_MODE_5 STABILIZE
|
||||
#define FLIGHT_MODE_6 STABILIZE
|
||||
|
||||
//#define ALWAYS_RESET_RADIO_RANGE 1
|
||||
//#define ALWAYS_RESET_MODES 1
|
||||
|
||||
#define GPS_PROTOCOL GPS_PROTOCOL_UBLOX
|
||||
|
||||
// Use MODE1 arming
|
||||
#define MOTOR_ARM_CONDITION (g.rc_3.control_in == 0 && g.rc_1.control_in > 2700)
|
||||
#define MOTOR_DISARM_CONDITION (g.rc_3.control_in == 0 && g.rc_1.control_in < -2700)
|
Loading…
Reference in New Issue