remove AP_AnalogSource library, deprecated under AP_HAL

This commit is contained in:
Pat Hickey 2012-12-03 11:40:58 -08:00 committed by Andrew Tridgell
parent 3987e81e2a
commit 1d21cea032
1 changed files with 0 additions and 203 deletions

View File

@ -1,203 +0,0 @@
/// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
#include <FastSerial.h>
#include "AP_AnalogSource_Arduino.h"
// increase this if we need more than 5 analog sources
#define MAX_PIN_SOURCES 5
// number of times to read a pin
// before considering the value valid.
// This ensures the value has settled on
// the new source
#define PIN_READ_REPEAT 2
static uint8_t num_pins_watched;
static uint8_t next_pin_index;
static uint8_t next_pin_count;
static volatile struct {
uint8_t pin;
uint8_t sum_count;
uint16_t output;
uint16_t sum;
} pins[MAX_PIN_SOURCES];
// ADC conversion timer. This is called at 1kHz by the timer
// interrupt
// each conversion takes about 125 microseconds
static void adc_timer(uint32_t t)
{
if (pins[next_pin_index].pin == ANALOG_PIN_NONE) {
goto next_pin;
}
if (bit_is_set(ADCSRA, ADSC) || num_pins_watched == 0) {
// conversion is still running. This should be
// very rare, as we are called at 1kHz
return;
}
next_pin_count++;
if (next_pin_count != PIN_READ_REPEAT) {
// we don't want this value, so start the next conversion
// immediately, discarding this value
ADCSRA |= _BV(ADSC);
return;
}
// remember the value we got
{
uint8_t low = ADCL;
uint8_t high = ADCH;
pins[next_pin_index].output = low | (high<<8);
}
pins[next_pin_index].sum += pins[next_pin_index].output;
if (pins[next_pin_index].sum_count >= 63) {
// we risk overflowing the 16 bit sum
pins[next_pin_index].sum >>= 1;
pins[next_pin_index].sum_count = 32;
} else {
pins[next_pin_index].sum_count++;
}
next_pin:
next_pin_count = 0;
if (num_pins_watched != 0) {
next_pin_index = (next_pin_index+1) % num_pins_watched;
}
uint8_t pin = pins[next_pin_index].pin;
if (pin == ANALOG_PIN_NONE) {
// setup for returning 0
pins[next_pin_index].output = 0;
pins[next_pin_index].sum = 0;
pins[next_pin_index].sum_count = 1;
} else if (pin == ANALOG_PIN_VCC) {
// we're reading the board voltage
ADMUX = _BV(REFS0)|_BV(MUX4)|_BV(MUX3)|_BV(MUX2)|_BV(MUX1);
// start the next conversion
ADCSRA |= _BV(ADSC);
} else {
// we're reading an external pin
ADCSRB = (ADCSRB & ~(1 << MUX5)) | (((pin >> 3) & 0x01) << MUX5);
ADMUX = _BV(REFS0) | (pin & 0x07);
// start the next conversion
ADCSRA |= _BV(ADSC);
}
}
// setup the timer process. This must be called before any analog
// values are available
void AP_AnalogSource_Arduino::init_timer(AP_PeriodicProcess * scheduler)
{
scheduler->register_process(adc_timer);
}
// read raw 16 bit value
uint16_t AP_AnalogSource_Arduino::read_raw(void)
{
uint16_t ret;
uint8_t oldSREG = SREG;
cli();
ret = pins[_pin_index].output;
SREG = oldSREG;
return ret;
}
// scaled read for board Vcc
uint16_t AP_AnalogSource_Arduino::read_vcc(void)
{
uint16_t v = read_raw();
if (v == 0) {
return 0;
}
return 1126400UL / v;
}
// read the average 16 bit value since the last
// time read_average() was called. This gives a very cheap
// filtered value, as new values are produced at 500/N Hz
// where N is the total number of analog sources
float AP_AnalogSource_Arduino::read_average(void)
{
uint16_t sum;
uint8_t sum_count;
// we don't expect this loop to trigger, unless
// you call read_average() very frequently
while (pins[_pin_index].sum_count == 0) ;
uint8_t oldSREG = SREG;
cli();
sum = pins[_pin_index].sum;
sum_count = pins[_pin_index].sum_count;
pins[_pin_index].sum = 0;
pins[_pin_index].sum_count = 0;
SREG = oldSREG;
return sum / (float)sum_count;
}
// read with the prescaler. This uses the averaged value since
// the last read, which matches that the AP_ADC APM1 library does
// for ADC sources
float AP_AnalogSource_Arduino::read(void)
{
return read_average() * _prescale;
}
// remap pin numbers to physical pin
uint8_t AP_AnalogSource_Arduino::_remap_pin(uint8_t pin)
{
if (pin != ANALOG_PIN_VCC && pin != ANALOG_PIN_NONE) {
// allow pin to be a channel (i.e. "A0") or an actual pin
#if defined(__AVR_ATmega1280__) || defined(__AVR_ATmega2560__)
if (pin >= 54) pin -= 54;
#elif defined(__AVR_ATmega32U4__)
if (pin >= 18) pin -= 18;
#elif defined(__AVR_ATmega1284__)
if (pin >= 24) pin -= 24;
#else
if (pin >= 14) pin -= 14;
#endif
}
return pin;
}
// assign a slot in the pins_watched
void AP_AnalogSource_Arduino::_assign_pin_index(uint8_t pin)
{
// ensure we don't try to read from too many analog pins
if (num_pins_watched == MAX_PIN_SOURCES) {
while (true) {
Serial.printf_P(PSTR("MAX_PIN_SOURCES REACHED\n"));
delay(1000);
}
}
pin = _remap_pin(pin);
_pin_index = num_pins_watched;
pins[_pin_index].pin = pin;
num_pins_watched++;
if (num_pins_watched == 1) {
// enable the ADC
PRR0 &= ~_BV(PRADC);
ADCSRA |= _BV(ADEN);
}
}
// change which pin to read
void AP_AnalogSource_Arduino::set_pin(uint8_t pin)
{
pin = _remap_pin(pin);
if (pins[_pin_index].pin != pin) {
uint8_t oldSREG = SREG;
cli();
pins[_pin_index].pin = pin;
pins[_pin_index].sum = 0;
pins[_pin_index].sum_count = 0;
SREG = oldSREG;
}
}