2023-06-13 18:40:10 -03:00
|
|
|
# hw definition file for processing by chibios_pins.py
|
|
|
|
|
# for BrainFPV RADIX 2 HD
|
|
|
|
|
|
|
|
|
|
# MCU class and specific type
|
|
|
|
|
MCU STM32H7xx STM32H750xx
|
|
|
|
|
|
|
|
|
|
# board ID for firmware load
|
|
|
|
|
APJ_BOARD_ID 1118
|
|
|
|
|
|
|
|
|
|
# crystal frequency, setup to use external oscillator
|
|
|
|
|
OSCILLATOR_HZ 16000000
|
|
|
|
|
|
|
|
|
|
MCU_CLOCKRATE_MHZ 480
|
|
|
|
|
|
|
|
|
|
env OPTIMIZE -O2
|
|
|
|
|
|
|
|
|
|
define HAL_WITH_EKF_DOUBLE 0
|
|
|
|
|
|
|
|
|
|
STM32_ST_USE_TIMER 13
|
|
|
|
|
define CH_CFG_ST_RESOLUTION 16
|
|
|
|
|
|
|
|
|
|
# internal flash is off limits
|
|
|
|
|
FLASH_SIZE_KB 128
|
|
|
|
|
FLASH_RESERVE_START_KB 0
|
|
|
|
|
define HAL_FLASH_PROTECTION 1
|
|
|
|
|
|
|
|
|
|
EXT_FLASH_SIZE_MB 16
|
|
|
|
|
EXT_FLASH_RESERVE_START_KB 4096
|
|
|
|
|
EXT_FLASH_RESERVE_END_KB 0
|
|
|
|
|
|
|
|
|
|
# Supports upto 2 MBits/s
|
|
|
|
|
CANFD_SUPPORTED 2
|
|
|
|
|
|
|
|
|
|
# only one I2C bus
|
|
|
|
|
I2C_ORDER I2C1
|
|
|
|
|
|
|
|
|
|
# order of UARTs (and USB)
|
2023-08-02 19:51:03 -03:00
|
|
|
SERIAL_ORDER OTG1 USART1 USART2 USART3 UART4 UART5 USART6 UART7
|
2023-06-13 18:40:10 -03:00
|
|
|
|
|
|
|
|
# I2C1 for baro
|
|
|
|
|
PB6 I2C1_SCL I2C1 PULLUP
|
|
|
|
|
PB7 I2C1_SDA I2C1 PULLUP
|
|
|
|
|
|
|
|
|
|
# Analog inputs
|
|
|
|
|
PC0 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
|
|
|
PA6 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
|
PC1 RSSI_ADC ADC1
|
|
|
|
|
|
|
|
|
|
define HAL_BATT_MONITOR_DEFAULT 4
|
|
|
|
|
define HAL_BATT_VOLT_PIN 10
|
|
|
|
|
define HAL_BATT_CURR_PIN 3
|
|
|
|
|
define HAL_BATT_VOLT_SCALE 17.6
|
|
|
|
|
define HAL_BATT_CURR_SCALE 28.5
|
|
|
|
|
define BOARD_RSSI_ANA_PIN 11
|
|
|
|
|
|
|
|
|
|
# Debug
|
|
|
|
|
PA13 JTMS-SWDIO SWD
|
|
|
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
|
|
|
|
|
|
# USB
|
|
|
|
|
PA11 OTG_FS_DM OTG1
|
|
|
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
|
|
|
|
|
|
# USART1 (HD OSD)
|
|
|
|
|
PB15 USART1_RX USART1
|
|
|
|
|
PB14 USART1_TX USART1
|
|
|
|
|
|
|
|
|
|
# USART2 (GPS)
|
|
|
|
|
PD6 USART2_RX USART2
|
|
|
|
|
PD5 USART2_TX USART2
|
|
|
|
|
|
|
|
|
|
# USART3 (RC input)
|
|
|
|
|
PB11 USART3_RX USART3
|
|
|
|
|
PD8 USART3_TX USART3
|
|
|
|
|
|
|
|
|
|
# UART4 (ESC telemetry)
|
|
|
|
|
PB8 UART4_RX UART4 NODMA
|
|
|
|
|
PA0 UART4_TX UART4 NODMA
|
|
|
|
|
|
|
|
|
|
# UART5 (spare)
|
|
|
|
|
PB12 UART5_RX UART5 NODMA
|
|
|
|
|
PB13 UART5_TX UART5 NODMA
|
|
|
|
|
|
|
|
|
|
# USART6 (spare)
|
|
|
|
|
PC7 USART6_RX USART6 NODMA ALT(1)
|
|
|
|
|
PC6 USART6_TX USART6 NODMA ALT(1)
|
|
|
|
|
|
2023-08-02 19:51:03 -03:00
|
|
|
# UART7 (spare, RX is on HD connector for RC input, TX is not connected to external pad)
|
|
|
|
|
PA8 UART7_RX UART7
|
|
|
|
|
PE8 UART7_TX UART7 NODMA
|
2023-06-13 18:40:10 -03:00
|
|
|
|
|
|
|
|
# CAN bus
|
|
|
|
|
PD0 CAN1_RX CAN1
|
|
|
|
|
PD1 CAN1_TX CAN1
|
|
|
|
|
|
|
|
|
|
# SP1 for BMI270
|
|
|
|
|
PA5 SPI1_SCK SPI1
|
|
|
|
|
PB4 SPI1_MISO SPI1
|
|
|
|
|
PD7 SPI1_MOSI SPI1
|
|
|
|
|
PD3 BMI270_CS CS
|
|
|
|
|
|
|
|
|
|
# SD card
|
|
|
|
|
PC8 SDMMC1_D0 SDMMC1
|
|
|
|
|
PC9 SDMMC1_D1 SDMMC1
|
|
|
|
|
PC10 SDMMC1_D2 SDMMC1
|
|
|
|
|
PC11 SDMMC1_D3 SDMMC1
|
|
|
|
|
PC12 SDMMC1_CK SDMMC1
|
|
|
|
|
PD2 SDMMC1_CMD SDMMC1
|
|
|
|
|
|
|
|
|
|
# QuadSPI Flash running at 120 MHz from HCLK
|
|
|
|
|
define HAL_FORCE_CLOCK_INIT
|
|
|
|
|
define STM32_QSPISEL STM32_QSPISEL_HCLK
|
|
|
|
|
PD11 QUADSPI_BK1_IO0 QUADSPI1 SPEED_HIGH
|
|
|
|
|
PD12 QUADSPI_BK1_IO1 QUADSPI1 SPEED_HIGH
|
|
|
|
|
PE2 QUADSPI_BK1_IO2 QUADSPI1 SPEED_HIGH
|
|
|
|
|
PA1 QUADSPI_BK1_IO3 QUADSPI1 SPEED_HIGH
|
|
|
|
|
PB10 QUADSPI_BK1_NCS QUADSPI1 SPEED_HIGH
|
|
|
|
|
PB2 QUADSPI_CLK QUADSPI1 SPEED_HIGH
|
|
|
|
|
|
|
|
|
|
# Motors
|
|
|
|
|
PE11 TIM1_CH2 TIM1 PWM(1) GPIO(50) BIDIR # M1
|
|
|
|
|
PE13 TIM1_CH3 TIM1 PWM(2) GPIO(51) BIDIR # M2
|
|
|
|
|
PA15 TIM2_CH1 TIM2 PWM(3) GPIO(52) BIDIR # M3
|
|
|
|
|
PA2 TIM2_CH3 TIM2 PWM(4) GPIO(53) BIDIR # M4
|
|
|
|
|
PB5 TIM3_CH2 TIM3 PWM(5) GPIO(54) BIDIR # M5
|
|
|
|
|
PB0 TIM3_CH3 TIM3 PWM(6) GPIO(55) BIDIR # M6
|
|
|
|
|
PD13 TIM4_CH2 TIM4 PWM(7) GPIO(56) BIDIR # M7
|
|
|
|
|
PD14 TIM4_CH3 TIM4 PWM(8) GPIO(57) BIDIR # M8
|
|
|
|
|
|
|
|
|
|
# PWM output on UART6 TX and RX pins
|
|
|
|
|
PC6 TIM8_CH1 TIM8 PWM(9) GPIO(58) NODMA # TX6
|
|
|
|
|
PC7 TIM8_CH2 TIM8 PWM(10) GPIO(59) NODMA # RX6
|
|
|
|
|
|
|
|
|
|
# RGB LED output: Currently not working: Needs to be inverted due to level shifter
|
|
|
|
|
PA3 TIM5_CH4 TIM5 PWM(11) GPIO(60)
|
|
|
|
|
|
|
|
|
|
# Buzzer pin
|
|
|
|
|
PE4 BUZZER OUTPUT LOW PULLDOWN GPIO(80)
|
|
|
|
|
define HAL_BUZZER_PIN 80
|
|
|
|
|
define AP_NOTIFY_TONEALARM_ENABLED 1
|
|
|
|
|
|
|
|
|
|
# LEDs
|
|
|
|
|
PE5 LED_RED OUTPUT HIGH OPENDRAIN GPIO(10)
|
|
|
|
|
PE6 LED_GREEN OUTPUT HIGH OPENDRAIN GPIO(11)
|
|
|
|
|
PA7 LED_BLUE OUTPUT HIGH OPENDRAIN GPIO(12)
|
|
|
|
|
|
|
|
|
|
define HAL_GPIO_A_LED_PIN 10
|
|
|
|
|
define HAL_GPIO_B_LED_PIN 11
|
|
|
|
|
define HAL_GPIO_C_LED_PIN 12
|
|
|
|
|
|
|
|
|
|
define HAL_GPIO_LED_ON 0
|
|
|
|
|
define HAL_GPIO_LED_OFF 1
|
|
|
|
|
|
|
|
|
|
define HAL_HAVE_PIXRACER_LED
|
|
|
|
|
|
|
|
|
|
# 9V regulator switch
|
|
|
|
|
PC14 VTX_PWR OUTPUT HIGH GPIO(81)
|
|
|
|
|
define RELAY2_PIN_DEFAULT 81
|
|
|
|
|
|
|
|
|
|
SPIDEV bmi270 SPI1 DEVID1 BMI270_CS MODE3 2*MHZ 10*MHZ
|
|
|
|
|
|
|
|
|
|
IMU BMI270 SPI:bmi270 ROTATION_ROLL_180
|
|
|
|
|
|
|
|
|
|
BARO DPS310 I2C:0:0x76
|
|
|
|
|
|
2023-10-17 19:48:15 -03:00
|
|
|
# probe external compasses (same bus as internal)
|
|
|
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
2023-11-30 18:10:47 -04:00
|
|
|
define HAL_I2C_INTERNAL_MASK 0
|
2023-10-17 19:48:15 -03:00
|
|
|
|
2023-06-13 18:40:10 -03:00
|
|
|
# filesystem setup on sdcard
|
|
|
|
|
define HAL_OS_FATFS_IO 1
|
|
|
|
|
|
|
|
|
|
define STM32_PWM_USE_ADVANCED TRUE
|
|
|
|
|
|
|
|
|
|
define HAL_STORAGE_SIZE 16384
|
|
|
|
|
|
|
|
|
|
# DMA
|
|
|
|
|
DMA_PRIORITY SPI1*
|
|
|
|
|
DMA_NOSHARE SPI1* TIM1* TIM2* TIM3* TIM4*
|
|
|
|
|
NODMA I2C*
|
|
|
|
|
define STM32_I2C_USE_DMA FALSE
|
2023-08-10 05:56:59 -03:00
|
|
|
|
|
|
|
|
# bootloader embedding / bootloader flashing not available
|
|
|
|
|
define AP_BOOTLOADER_FLASHING_ENABLED 0
|
