ardupilot/libraries/AP_ADC/AP_ADC_ADS7844.cpp

301 lines
8.1 KiB
C++
Raw Normal View History

/// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-
/*
AP_ADC_ADS7844.cpp - ADC ADS7844 Library for Ardupilot Mega
Code by Jordi Mu<EFBFBD>oz and Jose Julio. DIYDrones.com
Modified by John Ihlein 6 / 19 / 2010 to:
1)Prevent overflow of adc_counter when more than 8 samples collected between reads. Probably
only an issue on initial read of ADC at program start.
2)Reorder analog read order as follows:
p, q, r, ax, ay, az
This library is free software; you can redistribute it and / or
modify it under the terms of the GNU Lesser General Public
License as published by the Free Software Foundation; either
version 2.1 of the License, or (at your option) any later version.
External ADC ADS7844 is connected via Serial port 2 (in SPI mode)
TXD2 = MOSI = pin PH1
RXD2 = MISO = pin PH0
XCK2 = SCK = pin PH2
Chip Select pin is PC4 (33) [PH6 (9)]
We are using the 16 clocks per conversion timming to increase efficiency (fast)
The sampling frequency is 1kHz (Timer2 overflow interrupt)
So if our loop is at 50Hz, our needed sampling freq should be 100Hz, so
we have an 10x oversampling and averaging.
Methods:
Init() : Initialization of interrupts an Timers (Timer2 overflow interrupt)
Ch(ch_num) : Return the ADC channel value
// HJI - Input definitions. USB connector assumed to be on the left, Rx and servo
// connector pins to the rear. IMU shield components facing up. These are board
// referenced sensor inputs, not device referenced.
On Ardupilot Mega Hardware, oriented as described above:
Chennel 0 : yaw rate, r
Channel 1 : roll rate, p
Channel 2 : pitch rate, q
Channel 3 : x / y gyro temperature
Channel 4 : x acceleration, aX
Channel 5 : y acceleration, aY
Channel 6 : z acceleration, aZ
Channel 7 : Differential pressure sensor port
*/
extern "C" {
// AVR LibC Includes
#include <inttypes.h>
#include <stdint.h>
#include <avr/interrupt.h>
#include "WConstants.h"
}
#include "AP_ADC_ADS7844.h"
// Commands for reading ADC channels on ADS7844
static const unsigned char adc_cmd[9] = { 0x87, 0xC7, 0x97, 0xD7, 0xA7, 0xE7, 0xB7, 0xF7, 0x00 };
// the sum of the values since last read
static volatile uint32_t _sum[8];
// how many values we've accumulated since last read
static volatile uint16_t _count[8];
// a mask of what channels are actually being read. If a channel has
// never been read, then don't bother gathering it. That saves us a
// lot of cycles in the timer call
static uint8_t enable_mask;
static uint32_t last_ch6_micros;
// TCNT2 values for various interrupt rates,
// assuming 256 prescaler. Note that these values
// assume a zero-time ISR. The actual rate will be a
// bit lower than this
#define TCNT2_781_HZ (256-80)
#define TCNT2_1008_HZ (256-62)
#define TCNT2_1302_HZ (256-48)
static inline unsigned char ADC_SPI_transfer(unsigned char data)
{
/* Put data into buffer, sends the data */
UDR2 = data;
/* Wait for data to be received */
while ( !(UCSR2A & (1 << RXC2)) );
/* Get and return received data from buffer */
return UDR2;
}
void AP_ADC_ADS7844::read(void)
{
uint8_t ch;
unsigned char enable_cmd[9];
uint8_t num_enabled = 0;
if (enable_mask == 0) {
// no channels to read
return;
}
// build a sequence of commands to use to fetch the channels
for (ch = 0; ch < 8; ch++) {
if (enable_mask & (1<<ch)) {
enable_cmd[num_enabled++] = adc_cmd[ch];
}
}
enable_cmd[num_enabled] = 0;
num_enabled = 0;
bit_clear(PORTC, 4); // Enable Chip Select (PIN PC4)
ADC_SPI_transfer(enable_cmd[0]); // Command to read the first channel
for (ch = 0; ch < 8; ch++) {
uint16_t v;
if ((enable_mask & (1<<ch)) == 0) {
continue;
}
v = ADC_SPI_transfer(0) << 8; // Read first byte
v |= ADC_SPI_transfer(enable_cmd[++num_enabled]); // Read second byte and send next command
if (v & 0x8007) {
// this is a 12-bit ADC, shifted by 3 bits.
// if we get other bits set then the value is
// bogus and should be ignored
continue;
}
if (++_count[ch] == 0) {
// overflow ... shouldn't happen too often
// unless we're just not using the
// channel. Notice that we overflow the count
// to 1 here, not zero, as otherwise the
// reader below could get a division by zero
_sum[ch] = 0;
_count[ch] = 1;
last_ch6_micros = micros();
}
_sum[ch] += (v >> 3);
}
bit_set(PORTC, 4); // Disable Chip Select (PIN PC4)
}
// Constructors ////////////////////////////////////////////////////////////////
AP_ADC_ADS7844::AP_ADC_ADS7844() :
_filter_index_accel(0),
filter_result(false)
{
}
// Public Methods //////////////////////////////////////////////////////////////
void AP_ADC_ADS7844::Init( AP_PeriodicProcess * scheduler )
{
pinMode(ADC_CHIP_SELECT, OUTPUT);
digitalWrite(ADC_CHIP_SELECT, HIGH); // Disable device (Chip select is active low)
// Setup Serial Port2 in SPI mode
UBRR2 = 0;
DDRH |= (1 << PH2); // SPI clock XCK2 (PH2) as output. This enable SPI Master mode
// Set MSPI mode of operation and SPI data mode 0.
UCSR2C = (1 << UMSEL21) | (1 << UMSEL20); // |(0 << UCPHA2) | (0 << UCPOL2);
// Enable receiver and transmitter.
UCSR2B = (1 << RXEN2) | (1 << TXEN2);
// Set Baud rate
UBRR2 = 2; // SPI clock running at 2.6MHz
// get an initial value for each channel. This ensures
// _count[] is never zero
for (uint8_t i=0; i<8; i++) {
uint16_t adc_tmp;
adc_tmp = ADC_SPI_transfer(0) << 8;
adc_tmp |= ADC_SPI_transfer(adc_cmd[i + 1]);
_count[i] = 1;
_sum[i] = adc_tmp;
}
last_ch6_micros = micros();
scheduler->register_process( AP_ADC_ADS7844::read );
}
// enable a channel
void AP_ADC_ADS7844::enable_channel(uint8_t ch)
{
enable_mask |= (1<<ch);
}
// Read one channel value
float AP_ADC_ADS7844::Ch(uint8_t ch_num)
{
uint16_t count;
uint32_t sum;
enable_mask |= (1<<ch_num);
// ensure we have at least one value
while (_count[ch_num] == 0) /* noop */ ;
// grab the value with interrupts disabled, and clear the count
cli();
count = _count[ch_num];
sum = _sum[ch_num];
_count[ch_num] = 0;
_sum[ch_num] = 0;
sei();
return ((float)sum)/count;
}
// Read 6 channel values
// this assumes that the counts for all of the 6 channels are
// equal. This will only be true if we always consistently access a
// sensor by either Ch6() or Ch() and never mix them. If you mix them
// then you will get very strange results
uint32_t AP_ADC_ADS7844::Ch6(const uint8_t *channel_numbers, uint16_t *result)
{
uint16_t count[6];
uint32_t sum[6];
uint8_t i;
// ensure we have at least one value
for (i=0; i<6; i++) {
while (_count[channel_numbers[i]] == 0) /* noop */;
}
// grab the values with interrupts disabled, and clear the counts
cli();
for (i=0; i<6; i++) {
count[i] = _count[channel_numbers[i]];
sum[i] = _sum[channel_numbers[i]];
_count[channel_numbers[i]] = 0;
_sum[channel_numbers[i]] = 0;
}
sei();
// calculate averages. We keep this out of the cli region
// to prevent us stalling the ISR while doing the
// division. That costs us 36 bytes of stack, but I think its
// worth it.
for (i = 0; i < 6; i++) {
result[i] = (sum[i] + (count[i]/2)) / count[i];
}
if(filter_result){
uint32_t _sum_accel;
// simple Gyro Filter
for (i = 0; i < 3; i++) {
// add prev filtered value to new raw value, divide by 2
result[i] = (_prev_gyro[i] + result[i]) >> 1;
// remember the filtered value
_prev_gyro[i] = result[i];
}
// Accel filter
for (i = 0; i < 3; i++) {
// move most recent result into filter
_filter_accel[i][_filter_index_accel] = result[i+3];
// clear the sum
_sum_accel = 0;
// sum the filter
for (uint8_t n = 0; n < ADC_ACCEL_FILTER_SIZE; n++) {
_sum_accel += _filter_accel[i][n];
}
// filter does a moving average on last 8 reads, sums half with half of last filtered value
// save old result
_prev_accel[i] = result[i+3] = (_sum_accel >> 4) + (_prev_accel[i] >> 1); // divide by 16, divide by 2
}
// increment filter index
_filter_index_accel++;
// loop our filter
if(_filter_index_accel == ADC_ACCEL_FILTER_SIZE)
_filter_index_accel = 0;
}
// return number of microseconds since last call
uint32_t us = micros();
uint32_t ret = us - last_ch6_micros;
last_ch6_micros = us;
return ret;
}