ardupilot/ArduCopter/Copter.h

/// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: nil -*-

#define THISFIRMWARE "APM:Copter V3.4-dev"
#define FIRMWARE_VERSION 3,4,0,FIRMWARE_VERSION_TYPE_DEV

/*
   This program is free software: you can redistribute it and/or modify
   it under the terms of the GNU General Public License as published by
   the Free Software Foundation, either version 3 of the License, or
   (at your option) any later version.

   This program is distributed in the hope that it will be useful,
   but WITHOUT ANY WARRANTY; without even the implied warranty of
   MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
   GNU General Public License for more details.

   You should have received a copy of the GNU General Public License
   along with this program.  If not, see <http://www.gnu.org/licenses/>.
 */
/*
  This is the main Copter class
 */

////////////////////////////////////////////////////////////////////////////////
// Header includes
////////////////////////////////////////////////////////////////////////////////

#include <math.h>
#include <stdio.h>
#include <stdarg.h>

// Common dependencies
#include <AP_Common/AP_Common.h>
#include <AP_Progmem/AP_Progmem.h>
#include <AP_Menu/AP_Menu.h>
#include <AP_Param/AP_Param.h>
#include <StorageManager/StorageManager.h>
// AP_HAL
#include <AP_HAL/AP_HAL.h>
#include <AP_HAL_AVR/AP_HAL_AVR.h>
#include <AP_HAL_SITL/AP_HAL_SITL.h>
#include <AP_HAL_PX4/AP_HAL_PX4.h>
#include <AP_HAL_VRBRAIN/AP_HAL_VRBRAIN.h>
#include <AP_HAL_FLYMAPLE/AP_HAL_FLYMAPLE.h>
#include <AP_HAL_Linux/AP_HAL_Linux.h>
#include <AP_HAL_Empty/AP_HAL_Empty.h>

// Application dependencies
#include <GCS_MAVLink/GCS.h>
#include <GCS_MAVLink/GCS_MAVLink.h>        // MAVLink GCS definitions
#include <AP_SerialManager/AP_SerialManager.h>   // Serial manager library
#include <AP_GPS/AP_GPS.h>             // ArduPilot GPS library
#include <DataFlash/DataFlash.h>          // ArduPilot Mega Flash Memory Library
#include <AP_ADC/AP_ADC.h>             // ArduPilot Mega Analog to Digital Converter Library
#include <AP_ADC_AnalogSource/AP_ADC_AnalogSource.h>
#include <AP_Baro/AP_Baro.h>
#include <AP_Compass/AP_Compass.h>         // ArduPilot Mega Magnetometer Library
#include <AP_Math/AP_Math.h>            // ArduPilot Mega Vector/Matrix math Library
#include <AP_Curve/AP_Curve.h>           // Curve used to linearlise throttle pwm to thrust
#include <AP_InertialSensor/AP_InertialSensor.h>  // ArduPilot Mega Inertial Sensor (accel & gyro) Library
#include <AP_AHRS/AP_AHRS.h>
#include <AP_NavEKF/AP_NavEKF.h>
#include <AP_Mission/AP_Mission.h>         // Mission command library
#include <AP_Rally/AP_Rally.h>           // Rally point library
#include <AC_PID/AC_PID.h>             // PID library
#include <AC_PID/AC_PI_2D.h>           // PID library (2-axis)
#include <AC_PID/AC_HELI_PID.h>        // Heli specific Rate PID library
#include <AC_PID/AC_P.h>               // P library
#include <AC_AttitudeControl/AC_AttitudeControl_Multi.h> // Attitude control library
#include <AC_AttitudeControl/AC_AttitudeControl_Heli.h> // Attitude control library for traditional helicopter
#include <AC_AttitudeControl/AC_PosControl.h>      // Position control library
#include <RC_Channel/RC_Channel.h>         // RC Channel Library
#include <AP_Motors/AP_Motors.h>          // AP Motors library
#include <AP_RangeFinder/AP_RangeFinder.h>     // Range finder library
#include <AP_OpticalFlow/AP_OpticalFlow.h>     // Optical Flow library
#include <Filter/Filter.h>             // Filter library
#include <AP_Buffer/AP_Buffer.h>          // APM FIFO Buffer
#include <AP_Relay/AP_Relay.h>           // APM relay
#include <AP_ServoRelayEvents/AP_ServoRelayEvents.h>
#include <AP_Camera/AP_Camera.h>          // Photo or video camera
#include <AP_Mount/AP_Mount.h>           // Camera/Antenna mount
#include <AP_Airspeed/AP_Airspeed.h>        // needed for AHRS build
#include <AP_Vehicle/AP_Vehicle.h>         // needed for AHRS build
#include <AP_InertialNav/AP_InertialNav.h>     // ArduPilot Mega inertial navigation library
#include <AC_WPNav/AC_WPNav.h>           // ArduCopter waypoint navigation library
#include <AC_WPNav/AC_Circle.h>          // circle navigation library
#include <AP_Declination/AP_Declination.h>     // ArduPilot Mega Declination Helper Library
#include <AC_Fence/AC_Fence.h>           // Arducopter Fence library
#include <SITL/SITL.h>               // software in the loop support
#include <AP_Scheduler/AP_Scheduler.h>       // main loop scheduler
#include <AP_RCMapper/AP_RCMapper.h>        // RC input mapping library
#include <AP_Notify/AP_Notify.h>          // Notify library
#include <AP_BattMonitor/AP_BattMonitor.h>     // Battery monitor library
#include <AP_BoardConfig/AP_BoardConfig.h>     // board configuration library
#include <AP_Frsky_Telem/AP_Frsky_Telem.h>
#if SPRAYER == ENABLED
#include <AC_Sprayer/AC_Sprayer.h>         // crop sprayer library
#endif
#if EPM_ENABLED == ENABLED
#include <AP_EPM/AP_EPM.h>             // EPM cargo gripper stuff
#endif
#if PARACHUTE == ENABLED
#include <AP_Parachute/AP_Parachute.h>       // Parachute release library
#endif
#include <AP_LandingGear/AP_LandingGear.h>     // Landing Gear library
#include <AP_Terrain/AP_Terrain.h>
#include <AP_RPM/AP_RPM.h>

// AP_HAL to Arduino compatibility layer
// Configuration
#include "defines.h"
#include "config.h"
#include "config_channels.h"

// Local modules
#include "Parameters.h"

class Copter {
    public:
    friend class GCS_MAVLINK;
    friend class Parameters;

    Copter(void);
    void setup();
    void loop();

private:

    // key aircraft parameters passed to multiple libraries
    AP_Vehicle::MultiCopter aparm;


    // cliSerial isn't strictly necessary - it is an alias for hal.console. It may
    // be deprecated in favor of hal.console in later releases.
    AP_HAL::BetterStream* cliSerial;

    // Global parameters are all contained within the 'g' class.
    Parameters g;

    // main loop scheduler
    AP_Scheduler scheduler;

    // AP_Notify instance
    AP_Notify notify;

    // used to detect MAVLink acks from GCS to stop compassmot
    uint8_t command_ack_counter;

    // has a log download started?
    bool in_log_download;

    // primary input control channels
    RC_Channel *channel_roll;
    RC_Channel *channel_pitch;
    RC_Channel *channel_throttle;
    RC_Channel *channel_yaw;

    // Dataflash
    DataFlash_Class DataFlash;

    // the rate we run the main loop at
    const AP_InertialSensor::Sample_rate ins_sample_rate;

    AP_GPS gps;

    // flight modes convenience array
    AP_Int8 *flight_modes;

    AP_Baro barometer;
    Compass compass;
    AP_InertialSensor ins;

#if CONFIG_SONAR == ENABLED
    RangeFinder sonar;
    bool sonar_enabled; // enable user switch for sonar
#endif

    AP_RPM rpm_sensor;

    // Inertial Navigation EKF
    NavEKF EKF{&ahrs, barometer, sonar};
    AP_AHRS_NavEKF ahrs{ins, barometer, gps, sonar, EKF};

#if CONFIG_HAL_BOARD == HAL_BOARD_SITL
    SITL sitl;
#endif

    // Mission library
    AP_Mission mission;

    // Optical flow sensor
#if OPTFLOW == ENABLED
    OpticalFlow optflow;
#endif

    // gnd speed limit required to observe optical flow sensor limits
    float ekfGndSpdLimit;

    // scale factor applied to velocity controller gain to prevent optical flow noise causing excessive angle demand noise
    float ekfNavVelGainScaler;

    // GCS selection
    AP_SerialManager serial_manager;
    static const uint8_t num_gcs = MAVLINK_COMM_NUM_BUFFERS;

    GCS_MAVLINK gcs[MAVLINK_COMM_NUM_BUFFERS];

    // User variables
#ifdef USERHOOK_VARIABLES
# include USERHOOK_VARIABLES
#endif

    // Documentation of GLobals:
    union {
        struct {
            uint8_t unused1             : 1; // 0
            uint8_t simple_mode         : 2; // 1,2     // This is the state of simple mode : 0 = disabled ; 1 = SIMPLE ; 2 = SUPERSIMPLE
            uint8_t pre_arm_rc_check    : 1; // 3       // true if rc input pre-arm checks have been completed successfully
            uint8_t pre_arm_check       : 1; // 4       // true if all pre-arm checks (rc, accel calibration, gps lock) have been performed
            uint8_t auto_armed          : 1; // 5       // stops auto missions from beginning until throttle is raised
            uint8_t logging_started     : 1; // 6       // true if dataflash logging has started
            uint8_t land_complete       : 1; // 7       // true if we have detected a landing
            uint8_t new_radio_frame     : 1; // 8       // Set true if we have new PWM data to act on from the Radio
            uint8_t usb_connected       : 1; // 9       // true if APM is powered from USB connection
            uint8_t rc_receiver_present : 1; // 10      // true if we have an rc receiver present (i.e. if we've ever received an update
            uint8_t compass_mot         : 1; // 11      // true if we are currently performing compassmot calibration
            uint8_t motor_test          : 1; // 12      // true if we are currently performing the motors test
            uint8_t initialised         : 1; // 13      // true once the init_ardupilot function has completed.  Extended status to GCS is not sent until this completes
            uint8_t land_complete_maybe : 1; // 14      // true if we may have landed (less strict version of land_complete)
            uint8_t throttle_zero       : 1; // 15      // true if the throttle stick is at zero, debounced, determines if pilot intends shut-down when not using motor interlock
            uint8_t system_time_set     : 1; // 16      // true if the system time has been set from the GPS
            uint8_t gps_base_pos_set    : 1; // 17      // true when the gps base position has been set (used for RTK gps only)
            enum HomeState home_state   : 2; // 18,19   // home status (unset, set, locked)
            uint8_t using_interlock     : 1; // 20      // aux switch motor interlock function is in use
            uint8_t motor_emergency_stop: 1; // 21      // motor estop switch, shuts off motors when enabled
        };
        uint32_t value;
    } ap;

    // This is the state of the flight control system
    // There are multiple states defined such as STABILIZE, ACRO,
    int8_t control_mode;

    // Structure used to detect changes in the flight mode control switch
    struct {
        int8_t debounced_switch_position;   // currently used switch position
        int8_t last_switch_position;        // switch position in previous iteration
        uint32_t last_edge_time_ms;         // system time that switch position was last changed
    } control_switch_state;

    struct {
        bool running;
        float speed;
        uint32_t start_ms;
        uint32_t time_ms;
    } takeoff_state;

    RCMapper rcmap;

    // board specific config
    AP_BoardConfig BoardConfig;

    // receiver RSSI
    uint8_t receiver_rssi;

    // Failsafe
    struct {
        uint8_t rc_override_active  : 1; // 0   // true if rc control are overwritten by ground station
        uint8_t radio               : 1; // 1   // A status flag for the radio failsafe
        uint8_t battery             : 1; // 2   // A status flag for the battery failsafe
        uint8_t gcs                 : 1; // 4   // A status flag for the ground station failsafe
        uint8_t ekf                 : 1; // 5   // true if ekf failsafe has occurred

        int8_t radio_counter;            // number of iterations with throttle below throttle_fs_value

        uint32_t last_heartbeat_ms;      // the time when the last HEARTBEAT message arrived from a GCS - used for triggering gcs failsafe
    } failsafe;

    // sensor health for logging
    struct {
        uint8_t baro        : 1;    // true if baro is healthy
        uint8_t compass     : 1;    // true if compass is healthy
    } sensor_health;

    // Motor Output
#if FRAME_CONFIG == QUAD_FRAME
 #define MOTOR_CLASS AP_MotorsQuad
#elif FRAME_CONFIG == TRI_FRAME
 #define MOTOR_CLASS AP_MotorsTri
#elif FRAME_CONFIG == HEXA_FRAME
 #define MOTOR_CLASS AP_MotorsHexa
#elif FRAME_CONFIG == Y6_FRAME
 #define MOTOR_CLASS AP_MotorsY6
#elif FRAME_CONFIG == OCTA_FRAME
 #define MOTOR_CLASS AP_MotorsOcta
#elif FRAME_CONFIG == OCTA_QUAD_FRAME
 #define MOTOR_CLASS AP_MotorsOctaQuad
#elif FRAME_CONFIG == HELI_FRAME
 #define MOTOR_CLASS AP_MotorsHeli
#elif FRAME_CONFIG == SINGLE_FRAME
 #define MOTOR_CLASS AP_MotorsSingle
#elif FRAME_CONFIG == COAX_FRAME
 #define MOTOR_CLASS AP_MotorsCoax
#else
 #error Unrecognised frame type
#endif

    MOTOR_CLASS motors;

    // GPS variables
    // Sometimes we need to remove the scaling for distance calcs
    float scaleLongDown;

    // Location & Navigation
    int32_t wp_bearing;
    // The location of home in relation to the copter in centi-degrees
    int32_t home_bearing;
    // distance between plane and home in cm
    int32_t home_distance;
    // distance between plane and next waypoint in cm.
    uint32_t wp_distance;
    uint8_t land_state;              // records state of land (flying to location, descending)

    // Auto
    AutoMode auto_mode;   // controls which auto controller is run

    // Guided
    GuidedMode guided_mode;  // controls which controller is run (pos or vel)

    // RTL
    RTLState rtl_state;  // records state of rtl (initial climb, returning home, etc)
    bool rtl_state_complete; // set to true if the current state is completed
    float rtl_alt;     // altitude the vehicle is returning at

    // Circle
    bool circle_pilot_yaw_override; // true if pilot is overriding yaw

    // SIMPLE Mode
    // Used to track the orientation of the copter for Simple mode. This value is reset at each arming
    // or in SuperSimple mode when the copter leaves a 20m radius from home.
    float simple_cos_yaw;
    float simple_sin_yaw;
    int32_t super_simple_last_bearing;
    float super_simple_cos_yaw;
    float super_simple_sin_yaw;

    // Stores initial bearing when armed - initial simple bearing is modified in super simple mode so not suitable
    int32_t initial_armed_bearing;

    // Throttle variables
    float throttle_average;              // estimated throttle required to hover
    int16_t desired_climb_rate;          // pilot desired climb rate - for logging purposes only

    // Loiter control
    uint16_t loiter_time_max;                // How long we should stay in Loiter Mode for mission scripting (time in seconds)
    uint32_t loiter_time;                    // How long have we been loitering - The start time in millis

    // Flip
    Vector3f flip_orig_attitude;         // original copter attitude before flip

    // Battery Sensors
    AP_BattMonitor battery;

    // FrSky telemetry support
#if FRSKY_TELEM_ENABLED == ENABLED
    AP_Frsky_Telem frsky_telemetry;
#endif

    // Altitude
    // The cm/s we are moving up or down based on filtered data - Positive = UP
    int16_t climb_rate;
    // The altitude as reported by Sonar in cm - Values are 20 to 700 generally.
    int16_t sonar_alt;
    uint8_t sonar_alt_health;    // true if we can trust the altitude from the sonar
    float target_sonar_alt;      // desired altitude in cm above the ground
    int32_t baro_alt;            // barometer altitude in cm above home
    float baro_climbrate;        // barometer climbrate in cm/s
    LowPassFilterVector3f land_accel_ef_filter; // accelerations for land and crash detector tests

    // 3D Location vectors
    // Current location of the copter (altitude is relative to home)
    struct Location current_loc;

    // Navigation Yaw control
    // auto flight mode's yaw mode
    uint8_t auto_yaw_mode;

    // Yaw will point at this location if auto_yaw_mode is set to AUTO_YAW_ROI
    Vector3f roi_WP;

    // bearing from current location to the yaw_look_at_WP
    float yaw_look_at_WP_bearing;

    // yaw used for YAW_LOOK_AT_HEADING yaw_mode
    int32_t yaw_look_at_heading;

    // Deg/s we should turn
    int16_t yaw_look_at_heading_slew;

    // heading when in yaw_look_ahead_bearing
    float yaw_look_ahead_bearing;

    // Delay Mission Scripting Command
    int32_t condition_value;  // used in condition commands (eg delay, change alt, etc.)
    uint32_t condition_start;

    // IMU variables
    // Integration time (in seconds) for the gyros (DCM algorithm)
    // Updated with the fast loop
    float G_Dt;

    // Inertial Navigation
    AP_InertialNav_NavEKF inertial_nav;

    // Attitude, Position and Waypoint navigation objects
    // To-Do: move inertial nav up or other navigation variables down here
#if FRAME_CONFIG == HELI_FRAME
    AC_AttitudeControl_Heli attitude_control;
#else
    AC_AttitudeControl_Multi attitude_control;
#endif
    AC_PosControl pos_control;
    AC_WPNav wp_nav;
    AC_Circle circle_nav;

    // Performance monitoring
    int16_t pmTest1;

    // System Timers
    // --------------
    // Time in microseconds of main control loop
    uint32_t fast_loopTimer;
    // Counter of main loop executions.  Used for performance monitoring and failsafe processing
    uint16_t mainLoop_count;
    // Loiter timer - Records how long we have been in loiter
    uint32_t rtl_loiter_start_time;

    // Used to exit the roll and pitch auto trim function
    uint8_t auto_trim_counter;

    // Reference to the relay object
    AP_Relay relay;

    // handle repeated servo and relay events
    AP_ServoRelayEvents ServoRelayEvents;

    // Reference to the camera object (it uses the relay object inside it)
#if CAMERA == ENABLED
    AP_Camera camera;
#endif

    // a pin for reading the receiver RSSI voltage.
    AP_HAL::AnalogSource* rssi_analog_source;

    // Camera/Antenna mount tracking and stabilisation stuff
#if MOUNT == ENABLED
    // current_loc uses the baro/gps soloution for altitude rather than gps only.
    AP_Mount camera_mount;
#endif

    // AC_Fence library to reduce fly-aways
#if AC_FENCE == ENABLED
    AC_Fence    fence;
#endif

    // Rally library
#if AC_RALLY == ENABLED
    AP_Rally rally;
#endif

    // Crop Sprayer
#if SPRAYER == ENABLED
    AC_Sprayer sprayer;
#endif

    // EPM Cargo Griper
#if EPM_ENABLED == ENABLED
    AP_EPM epm;
#endif

    // Parachute release
#if PARACHUTE == ENABLED
    AP_Parachute parachute;
#endif

    // Landing Gear Controller
    AP_LandingGear landinggear;

    // terrain handling
#if AP_TERRAIN_AVAILABLE
    AP_Terrain terrain;
#endif

    // use this to prevent recursion during sensor init
    bool in_mavlink_delay;

    // true if we are out of time in our event timeslice
    bool gcs_out_of_time;

    // Top-level logic
    // setup the var_info table
    AP_Param param_loader;

#if FRAME_CONFIG == HELI_FRAME
    // Mode filter to reject RC Input glitches.  Filter size is 5, and it draws the 4th element, so it can reject 3 low glitches,
    // and 1 high glitch.  This is because any "off" glitches can be highly problematic for a helicopter running an ESC
    // governor.  Even a single "off" frame can cause the rotor to slow dramatically and take a long time to restart.
    ModeFilterInt16_Size5 rotor_speed_deglitch_filter {4};

    int16_t rsc_control_deglitched;

    // Tradheli flags
    struct {
        uint8_t dynamic_flight          : 1;    // 0   // true if we are moving at a significant speed (used to turn on/off leaky I terms)
        uint8_t init_targets_on_arming  : 1;    // 1   // true if we have been disarmed, and need to reset rate controller targets when we arm
    } heli_flags;
#endif

    static const AP_Scheduler::Task scheduler_tasks[];
    static const AP_Param::Info var_info[];
    static const struct LogStructure log_structure[];

    void compass_accumulate(void);
    void barometer_accumulate(void);
    void perf_update(void);
    void fast_loop();
    void rc_loop();
    void throttle_loop();
    void update_mount();
    void update_batt_compass(void);
    void ten_hz_logging_loop();
    void fifty_hz_logging_loop();
    void full_rate_logging_loop();
    void three_hz_loop();
    void one_hz_loop();
    void update_GPS(void);
    void init_simple_bearing();
    void update_simple_mode(void);
    void update_super_simple_bearing(bool force_update);
    void read_AHRS(void);
    void update_altitude();
    void set_home_state(enum HomeState new_home_state);
    bool home_is_set();
    void set_auto_armed(bool b);
    void set_simple_mode(uint8_t b);
    void set_failsafe_radio(bool b);
    void set_failsafe_battery(bool b);
    void set_failsafe_gcs(bool b);
    void set_land_complete(bool b);
    void set_land_complete_maybe(bool b);
    void set_pre_arm_check(bool b);
    void set_pre_arm_rc_check(bool b);
    void set_using_interlock(bool b);
    void set_motor_emergency_stop(bool b);
    float get_smoothing_gain();
    void get_pilot_desired_lean_angles(float roll_in, float pitch_in, float &roll_out, float &pitch_out);
    float get_pilot_desired_yaw_rate(int16_t stick_angle);
    void check_ekf_yaw_reset();
    float get_roi_yaw();
    float get_look_ahead_yaw();
    void update_thr_average();
    void set_throttle_takeoff();
    int16_t get_pilot_desired_throttle(int16_t throttle_control);
    float get_pilot_desired_climb_rate(float throttle_control);
    float get_non_takeoff_throttle();
    float get_takeoff_trigger_throttle();
    float get_throttle_pre_takeoff(float input_thr);
    float get_surface_tracking_climb_rate(int16_t target_rate, float current_alt_target, float dt);
    void set_accel_throttle_I_from_pilot_throttle(int16_t pilot_throttle);
    void update_poscon_alt_max();
    void rotate_body_frame_to_NE(float &x, float &y);
    void gcs_send_heartbeat(void);
    void gcs_send_deferred(void);
    void send_heartbeat(mavlink_channel_t chan);
    void send_attitude(mavlink_channel_t chan);
    void send_limits_status(mavlink_channel_t chan);
    void send_extended_status1(mavlink_channel_t chan);
    void send_location(mavlink_channel_t chan);
    void send_nav_controller_output(mavlink_channel_t chan);
    void send_simstate(mavlink_channel_t chan);
    void send_hwstatus(mavlink_channel_t chan);
    void send_servo_out(mavlink_channel_t chan);
    void send_radio_out(mavlink_channel_t chan);
    void send_vfr_hud(mavlink_channel_t chan);
    void send_current_waypoint(mavlink_channel_t chan);
    void send_rangefinder(mavlink_channel_t chan);
    void send_rpm(mavlink_channel_t chan);
    void rpm_update();
    void send_pid_tuning(mavlink_channel_t chan);
    void send_statustext(mavlink_channel_t chan);
    bool telemetry_delayed(mavlink_channel_t chan);
    void gcs_send_message(enum ap_message id);
    void gcs_send_mission_item_reached_message(uint16_t mission_index);
    void gcs_data_stream_send(void);
    void gcs_check_input(void);
    void gcs_send_text_P(gcs_severity severity, const prog_char_t *str);
    void do_erase_logs(void);
    void Log_Write_AutoTune(uint8_t axis, uint8_t tune_step, float meas_target, float meas_min, float meas_max, float new_gain_rp, float new_gain_rd, float new_gain_sp, float new_ddt);
    void Log_Write_AutoTuneDetails(float angle_cd, float rate_cds);
    void Log_Write_Current();
    void Log_Write_Optflow();
    void Log_Write_Nav_Tuning();
    void Log_Write_Control_Tuning();
    void Log_Write_Performance();
    void Log_Write_Attitude();
    void Log_Write_Rate();
    void Log_Write_MotBatt();
    void Log_Write_Startup();
    void Log_Write_Event(uint8_t id);
    void Log_Write_Data(uint8_t id, int32_t value);
    void Log_Write_Data(uint8_t id, uint32_t value);
    void Log_Write_Data(uint8_t id, int16_t value);
    void Log_Write_Data(uint8_t id, uint16_t value);
    void Log_Write_Data(uint8_t id, float value);
    void Log_Write_Error(uint8_t sub_system, uint8_t error_code);
    void Log_Write_Baro(void);
    void Log_Write_Parameter_Tuning(uint8_t param, float tuning_val, int16_t control_in, int16_t tune_low, int16_t tune_high);
    void Log_Write_Home_And_Origin();
    void Log_Sensor_Health();
#if FRAME_CONFIG == HELI_FRAME
    void Log_Write_Heli(void);
#endif
    void Log_Read(uint16_t log_num, uint16_t start_page, uint16_t end_page);
    void start_logging() ;
    void load_parameters(void);
    void userhook_init();
    void userhook_FastLoop();
    void userhook_50Hz();
    void userhook_MediumLoop();
    void userhook_SlowLoop();
    void userhook_SuperSlowLoop();
    void update_home_from_EKF();
    void set_home_to_current_location_inflight();
    bool set_home_to_current_location();
    bool set_home_to_current_location_and_lock();
    bool set_home_and_lock(const Location& loc);
    bool set_home(const Location& loc);
    bool far_from_EKF_origin(const Location& loc);
    void set_system_time_from_GPS();
    void exit_mission();
    void do_RTL(void);
    bool verify_takeoff();
    bool verify_land();
    bool verify_loiter_unlimited();
    bool verify_loiter_time();
    bool verify_RTL();
    bool verify_wait_delay();
    bool verify_change_alt();
    bool verify_within_distance();
    bool verify_yaw();
    void do_take_picture();
    void log_picture();
    uint8_t mavlink_compassmot(mavlink_channel_t chan);
    void delay(uint32_t ms);
    uint32_t millis();
    uint32_t micros();
    bool acro_init(bool ignore_checks);
    void acro_run();
    void get_pilot_desired_angle_rates(int16_t roll_in, int16_t pitch_in, int16_t yaw_in, float &roll_out, float &pitch_out, float &yaw_out);
    bool althold_init(bool ignore_checks);
    void althold_run();
    bool auto_init(bool ignore_checks);
    void auto_run();
    void auto_takeoff_start(float final_alt_above_home);
    void auto_takeoff_run();
    void auto_wp_start(const Vector3f& destination);
    void auto_wp_run();
    void auto_spline_run();
    void auto_land_start();
    void auto_land_start(const Vector3f& destination);
    void auto_land_run();
    void auto_rtl_start();
    void auto_rtl_run();
    void auto_circle_movetoedge_start();
    void auto_circle_start();
    void auto_circle_run();
    void auto_nav_guided_start();
    void auto_nav_guided_run();
    bool auto_loiter_start();
    void auto_loiter_run();
    uint8_t get_default_auto_yaw_mode(bool rtl);
    void set_auto_yaw_mode(uint8_t yaw_mode);
    void set_auto_yaw_look_at_heading(float angle_deg, float turn_rate_dps, int8_t direction, uint8_t relative_angle);
    void set_auto_yaw_roi(const Location &roi_location);
    float get_auto_heading(void);
    bool autotune_init(bool ignore_checks);
    void autotune_stop();
    bool autotune_start(bool ignore_checks);
    void autotune_run();
    void autotune_attitude_control();
    void autotune_backup_gains_and_initialise();
    void autotune_load_orig_gains();
    void autotune_load_tuned_gains();
    void autotune_load_intra_test_gains();
    void autotune_load_twitch_gains();
    void autotune_save_tuning_gains();
    void autotune_update_gcs(uint8_t message_id);
    bool autotune_roll_enabled();
    bool autotune_pitch_enabled();
    bool autotune_yaw_enabled();
    void autotune_twitching_test(float measurement, float target, float &measurement_min, float &measurement_max);
    void autotune_updating_d_up(float &tune_d, float tune_d_min, float tune_d_max, float tune_d_step_ratio, float &tune_p, float tune_p_min, float tune_p_max, float tune_p_step_ratio, float target, float measurement_min, float measurement_max);
    void autotune_updating_d_down(float &tune_d, float tune_d_min, float tune_d_step_ratio, float &tune_p, float tune_p_min, float tune_p_max, float tune_p_step_ratio, float target, float measurement_min, float measurement_max);
    void autotune_updating_p_down(float &tune_p, float tune_p_min, float tune_p_step_ratio, float target, float measurement_max);
    void autotune_updating_p_up(float &tune_p, float tune_p_max, float tune_p_step_ratio, float target, float measurement_max);
    void autotune_updating_p_up_d_down(float &tune_d, float tune_d_min, float tune_d_step_ratio, float &tune_p, float tune_p_min, float tune_p_max, float tune_p_step_ratio, float target, float measurement_min, float measurement_max);
    void autotune_twitching_measure_acceleration(float &rate_of_change, float rate_measurement, float &rate_measurement_max);
    bool brake_init(bool ignore_checks);
    void brake_run();
    bool circle_init(bool ignore_checks);
    void circle_run();
    bool drift_init(bool ignore_checks);
    void drift_run();
    int16_t get_throttle_assist(float velz, int16_t pilot_throttle_scaled);
    bool flip_init(bool ignore_checks);
    void flip_run();
    bool guided_init(bool ignore_checks);
    void guided_takeoff_start(float final_alt_above_home);
    void guided_pos_control_start();
    void guided_vel_control_start();
    void guided_posvel_control_start();
    void guided_set_destination(const Vector3f& destination);
    void guided_set_velocity(const Vector3f& velocity);
    void guided_set_destination_posvel(const Vector3f& destination, const Vector3f& velocity);
    void guided_run();
    void guided_takeoff_run();
    void guided_pos_control_run();
    void guided_vel_control_run();
    void guided_posvel_control_run();
    void guided_limit_clear();
    void guided_limit_set(uint32_t timeout_ms, float alt_min_cm, float alt_max_cm, float horiz_max_cm);
    void guided_limit_init_time_and_pos();
    bool guided_limit_check();
    bool land_init(bool ignore_checks);
    void land_run();
    void land_gps_run();
    void land_nogps_run();
    float get_land_descent_speed();
    void land_do_not_use_GPS();
    void set_mode_land_with_pause();
    bool landing_with_GPS();
    bool loiter_init(bool ignore_checks);
    void loiter_run();
    bool poshold_init(bool ignore_checks);
    void poshold_run();
    void poshold_update_pilot_lean_angle(float &lean_angle_filtered, float &lean_angle_raw);
    int16_t poshold_mix_controls(float mix_ratio, int16_t first_control, int16_t second_control);
    void poshold_update_brake_angle_from_velocity(int16_t &brake_angle, float velocity);
    void poshold_update_wind_comp_estimate();
    void poshold_get_wind_comp_lean_angles(int16_t &roll_angle, int16_t &pitch_angle);
    void poshold_roll_controller_to_pilot_override();
    void poshold_pitch_controller_to_pilot_override();

    bool rtl_init(bool ignore_checks);
    void rtl_run();
    void rtl_climb_start();
    void rtl_return_start();
    void rtl_climb_return_run();
    void rtl_loiterathome_start();
    void rtl_loiterathome_run();
    void rtl_descent_start();
    void rtl_descent_run();
    void rtl_land_start();
    void rtl_land_run();
    float get_RTL_alt();
    bool sport_init(bool ignore_checks);
    void sport_run();
    bool stabilize_init(bool ignore_checks);
    void stabilize_run();
    void crash_check();
    void parachute_check();
    void parachute_release();
    void parachute_manual_release();
    void ekf_check();
    bool ekf_over_threshold();
    void failsafe_ekf_event();
    void failsafe_ekf_off_event(void);
    void esc_calibration_startup_check();
    void esc_calibration_passthrough();
    void esc_calibration_auto();
    void failsafe_radio_on_event();
    void failsafe_radio_off_event();
    void failsafe_battery_event(void);
    void failsafe_gcs_check();
    void failsafe_gcs_off_event(void);
    void set_mode_RTL_or_land_with_pause();
    void update_events();
    void failsafe_enable();
    void failsafe_disable();
    void fence_check();
    void fence_send_mavlink_status(mavlink_channel_t chan);
    bool set_mode(uint8_t mode);
    void update_flight_mode();
    void exit_mode(uint8_t old_control_mode, uint8_t new_control_mode);
    bool mode_requires_GPS(uint8_t mode);
    bool mode_has_manual_throttle(uint8_t mode);
    bool mode_allows_arming(uint8_t mode, bool arming_from_gcs);
    void notify_flight_mode(uint8_t mode);
    void heli_init();
    int16_t get_pilot_desired_collective(int16_t control_in);
    void check_dynamic_flight(void);
    void update_heli_control_dynamics(void);
    void heli_update_landing_swash();
    void heli_update_rotor_speed_targets();
    void heli_radio_passthrough();
    bool heli_acro_init(bool ignore_checks);
    void heli_acro_run();
    void get_pilot_desired_yaw_rate(int16_t yaw_in, float &yaw_out);
    bool heli_stabilize_init(bool ignore_checks);
    void heli_stabilize_run();
    void read_inertia();
    void read_inertial_altitude();
    bool land_complete_maybe();
    void update_land_and_crash_detectors();
    void update_land_detector();
    void update_throttle_thr_mix();
    void landinggear_update();
    void update_notify();
    void motor_test_output();
    bool mavlink_motor_test_check(mavlink_channel_t chan, bool check_rc);
    uint8_t mavlink_motor_test_start(mavlink_channel_t chan, uint8_t motor_seq, uint8_t throttle_type, uint16_t throttle_value, float timeout_sec);
    void motor_test_stop();
    void arm_motors_check();
    void auto_disarm_check();
    bool init_arm_motors(bool arming_from_gcs);
    bool pre_arm_checks(bool display_failure);
    void pre_arm_rc_checks();
    bool pre_arm_gps_checks(bool display_failure);
    bool arm_checks(bool display_failure, bool arming_from_gcs);
    void init_disarm_motors();
    void motors_output();
    void lost_vehicle_check();
    void run_nav_updates(void);
    void calc_position();
    void calc_distance_and_bearing();
    void calc_wp_distance();
    void calc_wp_bearing();
    void calc_home_distance_and_bearing();
    void run_autopilot();
    void perf_info_reset();
    void perf_ignore_this_loop();
    void perf_info_check_loop_time(uint32_t time_in_micros);
    uint16_t perf_info_get_num_loops();
    uint32_t perf_info_get_max_time();
    uint32_t perf_info_get_min_time();
    uint16_t perf_info_get_num_long_running();
    Vector3f pv_location_to_vector(const Location& loc);
    Vector3f pv_location_to_vector_with_default(const Location& loc, const Vector3f& default_posvec);
    float pv_alt_above_origin(float alt_above_home_cm);
    float pv_alt_above_home(float alt_above_origin_cm);
    float pv_get_bearing_cd(const Vector3f &origin, const Vector3f &destination);
    float pv_get_horizontal_distance_cm(const Vector3f &origin, const Vector3f &destination);
    void default_dead_zones();
    void init_rc_in();
    void init_rc_out();
    void enable_motor_output();
    void read_radio();
    void set_throttle_and_failsafe(uint16_t throttle_pwm);
    void set_throttle_zero_flag(int16_t throttle_control);
    void init_barometer(bool full_calibration);
    void read_barometer(void);
    void init_sonar(void);
    int16_t read_sonar(void);
    void init_compass();
    void init_optflow();
    void update_optical_flow(void);
    void read_battery(void);
    void read_receiver_rssi(void);
    void epm_update();
    void report_batt_monitor();
    void report_frame();
    void report_radio();
    void report_ins();
    void report_flight_modes();
    void report_optflow();
    void print_radio_values();
    void print_switch(uint8_t p, uint8_t m, bool b);
    void print_accel_offsets_and_scaling(void);
    void print_gyro_offsets(void);
    void report_compass();
    void print_blanks(int16_t num);
    void print_divider(void);
    void print_enabled(bool b);
    void report_version();
    void read_control_switch();
    bool check_if_auxsw_mode_used(uint8_t auxsw_mode_check);
    bool check_duplicate_auxsw(void);
    void reset_control_switch();
    uint8_t read_3pos_switch(int16_t radio_in);
    void read_aux_switches();
    void init_aux_switches();
    void init_aux_switch_function(int8_t ch_option, uint8_t ch_flag);
    void do_aux_switch_function(int8_t ch_function, uint8_t ch_flag);
    void save_trim();
    void auto_trim();
    void init_ardupilot();
    void startup_ground(bool force_gyro_cal);
    bool position_ok();
    bool ekf_position_ok();
    bool optflow_position_ok();
    void update_auto_armed();
    void check_usb_mux(void);
    void frsky_telemetry_send(void);
    bool should_log(uint32_t mask);
    bool current_mode_has_user_takeoff(bool must_navigate);
    bool do_user_takeoff(float takeoff_alt_cm, bool must_navigate);
    void takeoff_timer_start(float alt_cm);
    void takeoff_stop();
    void takeoff_get_climb_rates(float& pilot_climb_rate, float& takeoff_climb_rate);
    void print_hit_enter();
    void tuning();
    void gcs_send_text_fmt(const prog_char_t *fmt, ...);
    bool start_command(const AP_Mission::Mission_Command& cmd);
    bool verify_command(const AP_Mission::Mission_Command& cmd);
    bool verify_command_callback(const AP_Mission::Mission_Command& cmd);

    bool do_guided(const AP_Mission::Mission_Command& cmd);
    void do_takeoff(const AP_Mission::Mission_Command& cmd);
    void do_nav_wp(const AP_Mission::Mission_Command& cmd);
    void do_land(const AP_Mission::Mission_Command& cmd);
    void do_loiter_unlimited(const AP_Mission::Mission_Command& cmd);
    void do_circle(const AP_Mission::Mission_Command& cmd);
    void do_loiter_time(const AP_Mission::Mission_Command& cmd);
    void do_spline_wp(const AP_Mission::Mission_Command& cmd);
#if NAV_GUIDED == ENABLED
    void do_nav_guided_enable(const AP_Mission::Mission_Command& cmd);
    void do_guided_limits(const AP_Mission::Mission_Command& cmd);
#endif
    void do_wait_delay(const AP_Mission::Mission_Command& cmd);
    void do_within_distance(const AP_Mission::Mission_Command& cmd);
    void do_change_alt(const AP_Mission::Mission_Command& cmd);
    void do_yaw(const AP_Mission::Mission_Command& cmd);
    void do_change_speed(const AP_Mission::Mission_Command& cmd);
    void do_set_home(const AP_Mission::Mission_Command& cmd);
    void do_roi(const AP_Mission::Mission_Command& cmd);
    void do_mount_control(const AP_Mission::Mission_Command& cmd);
#if CAMERA == ENABLED
    void do_digicam_configure(const AP_Mission::Mission_Command& cmd);
    void do_digicam_control(const AP_Mission::Mission_Command& cmd);
#endif
#if PARACHUTE == ENABLED
    void do_parachute(const AP_Mission::Mission_Command& cmd);
#endif
#if EPM_ENABLED == ENABLED
    void do_gripper(const AP_Mission::Mission_Command& cmd);
#endif
    bool verify_nav_wp(const AP_Mission::Mission_Command& cmd);
    bool verify_circle(const AP_Mission::Mission_Command& cmd);
    bool verify_spline_wp(const AP_Mission::Mission_Command& cmd);
#if NAV_GUIDED == ENABLED
    bool verify_nav_guided_enable(const AP_Mission::Mission_Command& cmd);
#endif
    void auto_spline_start(const Vector3f& destination, bool stopped_at_start, AC_WPNav::spline_segment_end_type seg_end_type, const Vector3f& next_spline_destination);

    void print_flight_mode(AP_HAL::BetterStream *port, uint8_t mode);
    void log_init(void);
    void run_cli(AP_HAL::UARTDriver *port);
    void init_capabilities(void);

public:
    void mavlink_delay_cb();
    void failsafe_check();
    int8_t dump_log(uint8_t argc, const Menu::arg *argv);
    int8_t erase_logs(uint8_t argc, const Menu::arg *argv);
    int8_t select_logs(uint8_t argc, const Menu::arg *argv);
    bool print_log_menu(void);

    int8_t process_logs(uint8_t argc, const Menu::arg *argv);
    int8_t main_menu_help(uint8_t, const Menu::arg*);
    int8_t setup_mode(uint8_t argc, const Menu::arg *argv);
    int8_t setup_factory(uint8_t argc, const Menu::arg *argv);
    int8_t setup_set(uint8_t argc, const Menu::arg *argv);
    int8_t setup_show(uint8_t argc, const Menu::arg *argv);
    int8_t esc_calib(uint8_t argc, const Menu::arg *argv);

    int8_t test_mode(uint8_t argc, const Menu::arg *argv);
    int8_t test_baro(uint8_t argc, const Menu::arg *argv);
    int8_t test_compass(uint8_t argc, const Menu::arg *argv);
    int8_t test_ins(uint8_t argc, const Menu::arg *argv);
    int8_t test_optflow(uint8_t argc, const Menu::arg *argv);
    int8_t test_relay(uint8_t argc, const Menu::arg *argv);
    int8_t test_shell(uint8_t argc, const Menu::arg *argv);
    int8_t test_sonar(uint8_t argc, const Menu::arg *argv);

    int8_t reboot_board(uint8_t argc, const Menu::arg *argv);
};

#define MENU_FUNC(func) FUNCTOR_BIND(&copter, &Copter::func, int8_t, uint8_t, const Menu::arg *)

extern const AP_HAL::HAL& hal;
extern Copter copter;