ardupilot/libraries/AP_Scripting/applets/Aerobatics/FixedWing/Schedules/NZClubMan.txt

#   trajectory tracking aerobatic control
#   See README.md for usage
#   Written by Matthew Hampsey, Andy Palmer and Andrew Tridgell, with controller
#   assistance from Paul Riseborough, testing by Henry Wurzburg

# To use this schedule put the file on your microSD in the root directory 
# (not the APM directory) with name trick90.txt The schedule can then be 
# used in auto missions or in TRIKn_ID commands for tricks on a switch

# This schedule is set up to be flown Left to Right. The schedule starts downwind - so 
# the mission should be set up with WP's lined up on the flight line (150m out from the 
# pilot), and the mission should be triggered when the plane gets to the center marker 
# heading RIGHT to LEFT. Schedule direction is reversed with aerom_scale = -1 (and 
# remember to reverse the mission WP's as well). Note the required height is greater 
# than 400 feet - so only fly at an airfield where there is a 1500 foot clearance

# This is the New Zealand Clubman Aerobatics schedule. Please understand the behaviour 
# by flying in SITL before flying this schedule with a real aircraft! Your aircraft 
# requires adequate performance to complete the schedule

name: NZClubmanSchedule

function half_reverse_cuban_eight(r, arg2, arg3, arg4)
   local rabs = math.abs(r)
   return make_paths("half_reverse_cuban_eight", {
         { path_vertical_arc(r,  45),   roll_angle(0) },
         { path_straight(2*rabs/3),     roll_angle(0) },
         { path_straight(2*rabs/3),     roll_angle(180) },
         { path_straight(2*rabs/3),     roll_angle(0) },
         { path_vertical_arc(-r, 225),  roll_angle(0) },
   })
end

function cuban_eight(r, arg2, arg3, arg4)
   local rabs = math.abs(r)
   return make_paths("cuban_eight", {
         --{ path_straight(rabs*math.sqrt(2)), roll_angle(0) },
         { path_vertical_arc(r,  225),       roll_angle(0) },
         { path_straight(2*rabs/3),          roll_angle(0) },
         { path_straight(2*rabs/3),          roll_angle(180) },
         { path_straight(2*rabs/3),          roll_angle(0) },
         { path_vertical_arc(-r, 270),       roll_angle(0) },
         { path_straight(2*rabs/3),          roll_angle(0) },
         { path_straight(2*rabs/3),          roll_angle(180) },
         { path_straight(2*rabs/3),          roll_angle(0) },
         { path_vertical_arc(r, 45),         roll_angle(0) },
   })
end

function multi_point_roll(length, N, hold_frac, num_points)
   if hold_frac <= 0 then
      hold_frac = 0.2
   end
   if num_points <= 0 then
      num_points = N
   end
   --[[
      construct a roll sequence to use over the full length
   --]]
   local seq = {}
   local roll_frac = 1.0 - hold_frac
   for i = 1, num_points do
      seq[#seq+1] = { roll_frac, 360 / N }
      if i < num_points then
         seq[#seq+1] = { hold_frac, 0 }
      end
   end
   return make_paths("multi_point_roll", {{ path_straight(length), roll_sequence(seq) }})
end

function upline_45(r, height_gain, arg3, arg4)
   --local h = (height_gain - 2*r*(1.0-math.cos(math.rad(45))))/math.sin(math.rad(45))
   local h = (height_gain - (2 * r) + (2 * r * math.cos(math.rad(45)))) / math.cos(math.rad(45))
  assert(h >= 0)
   return make_paths("upline_45", {
         { path_vertical_arc(r, 45),  roll_angle(0) },
         { path_straight(h),          roll_angle(0) },
         { path_vertical_arc(-r, 45), roll_angle(0) },
   })
end

function split_s(r, arg2, arg3, arg4)
   local rabs = math.abs(r)
   return make_paths("split_s", {
         { path_straight(rabs/2),                roll_angle(180) },
         { path_vertical_arc(-r, 180),           roll_angle(0) },
   })
end

function half_cuban_eight(r, arg2, arg3, arg4)
   local rabs = math.abs(r)
   return make_paths("half_cuban_eight", {
         { path_straight(2*rabs*math.sqrt(2)), roll_angle(0) },
         { path_vertical_arc(r,  225),         roll_angle(0) },
         { path_straight(2*rabs/3),            roll_angle(0) },
         { path_straight(2*rabs/3),            roll_angle(180) },
         { path_straight(2*rabs/3),            roll_angle(0) },
         { path_vertical_arc(-r, 45),          roll_angle(0) },
   })
end

function loop(radius, bank_angle, num_loops, arg4)
   if not num_loops or num_loops <= 0 then
      num_loops = 1
   end
   return make_paths("loop", {
         { path_vertical_arc(radius, 360*num_loops), roll_angle_entry_exit(bank_angle) },
   })
end

function immelmann_turn(r, arg2, arg3, arg4)
   local rabs = math.abs(r)
   return make_paths("immelmann_turn", {
         { path_vertical_arc(r, 180),      roll_angle(0) },
         { path_straight(rabs/2),          roll_angle(180) },
   })
end

function downline_45(r, height_loss, arg3, arg4)
   local h = (height_loss - 2*r*(1.0-math.cos(math.rad(45))))/math.sin(math.rad(45))
   assert(h >= 0)
   return make_paths("downline_45", {
         { path_vertical_arc(-r, 45),  roll_angle(0) },
         { path_straight(h),           roll_angle(0) },
         { path_vertical_arc(r, 45),   roll_angle(0) },
   })
end

straight_roll 100 0
half_reverse_cuban_eight 80

align_center
message: CubanEight
cuban_eight 80

straight_align -130
half_reverse_cuban_eight 80

straight_align 40
message: HalfReverseCuban
half_reverse_cuban_eight 80

straight_align -180
half_reverse_cuban_eight 80

align_center
message: TwoPointRoll
thr_boost: true
multi_point_roll 240 2 0.8 2

straight_align 150
half_reverse_cuban_eight 80

align_center
message: 45DegreeUpline
upline_45 40 180

straight_align -200
split_s 90 90

align_center
message: SlowRoll
thr_boost: true 
straight_roll 240 1

straight_align 130
half_cuban_eight 80

align_center
message: TwoLoops
loop 80 0 2

straight_align -210
immelmann_turn 90 90

align_center
message: 45DegreeDownline
downline_45 40 180

straight_align 150
half_cuban_eight 80
straight_roll 100