2021-10-28 18:46:39 -03:00
|
|
|
# hw definition file for processing by chibios_hwdef.py
|
|
|
|
|
# for SmartAP AIRLink hardware
|
|
|
|
|
|
|
|
|
|
# MCU class and specific type
|
|
|
|
|
MCU STM32F7xx STM32F767xx
|
|
|
|
|
|
|
|
|
|
# crystal frequency
|
|
|
|
|
OSCILLATOR_HZ 16000000
|
|
|
|
|
|
|
|
|
|
# default to all pins low to avoid ESD issues
|
|
|
|
|
DEFAULTGPIO OUTPUT LOW PULLDOWN
|
|
|
|
|
|
|
|
|
|
# board ID for firmware load
|
|
|
|
|
APJ_BOARD_ID 55
|
|
|
|
|
|
|
|
|
|
FLASH_RESERVE_START_KB 32
|
|
|
|
|
|
|
|
|
|
# flash size
|
|
|
|
|
FLASH_SIZE_KB 2048
|
|
|
|
|
|
|
|
|
|
env OPTIMIZE -O2
|
|
|
|
|
|
|
|
|
|
# order of UARTs (and USB)
|
2022-09-12 19:45:53 -03:00
|
|
|
SERIAL_ORDER OTG1 UART7 UART5 USART1 UART8 USART3 USART2 OTG2
|
2021-10-28 18:46:39 -03:00
|
|
|
|
|
|
|
|
# default the 2nd interface to MAVLink2
|
|
|
|
|
define HAL_OTG1_PROTOCOL SerialProtocol_MAVLink2
|
|
|
|
|
|
|
|
|
|
# USB support
|
|
|
|
|
PA11 OTG_FS_DM OTG1
|
|
|
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
|
|
|
|
|
|
# debugging support
|
|
|
|
|
PA13 JTMS-SWDIO SWD
|
|
|
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
|
|
|
|
|
|
# SPI1 - ICM20602
|
|
|
|
|
PA5 SPI1_SCK SPI1
|
|
|
|
|
PB4 SPI1_MISO SPI1
|
|
|
|
|
PB5 SPI1_MOSI SPI1
|
|
|
|
|
|
|
|
|
|
# SPI2 - MPU9250 FPC
|
|
|
|
|
PI1 SPI2_SCK SPI2
|
|
|
|
|
PI2 SPI2_MISO SPI2
|
|
|
|
|
PI3 SPI2_MOSI SPI2
|
|
|
|
|
|
|
|
|
|
# SPI3 - MPU9250 Board
|
|
|
|
|
PC10 SPI3_SCK SPI3
|
|
|
|
|
PC11 SPI3_MISO SPI3
|
|
|
|
|
PB2 SPI3_MOSI SPI3
|
|
|
|
|
|
|
|
|
|
# SPI5 - FRAM
|
|
|
|
|
PF7 SPI5_SCK SPI5
|
|
|
|
|
PF8 SPI5_MISO SPI5
|
|
|
|
|
PF11 SPI5_MOSI SPI5
|
|
|
|
|
|
|
|
|
|
# sensor CS
|
|
|
|
|
PI9 ICM20602_CS CS SPEED_VERYLOW
|
|
|
|
|
PH5 MPU_FPC_CS CS
|
|
|
|
|
PI8 MPU_BOARD_CS CS
|
|
|
|
|
PG7 FRAM_CS CS SPEED_VERYLOW
|
|
|
|
|
|
|
|
|
|
# I2C buses
|
|
|
|
|
PB8 I2C1_SCL I2C1
|
|
|
|
|
PB7 I2C1_SDA I2C1
|
|
|
|
|
|
|
|
|
|
PF1 I2C2_SCL I2C2
|
|
|
|
|
PF0 I2C2_SDA I2C2
|
|
|
|
|
|
|
|
|
|
PH7 I2C3_SCL I2C3
|
|
|
|
|
PH8 I2C3_SDA I2C3
|
|
|
|
|
|
|
|
|
|
PF14 I2C4_SCL I2C4
|
|
|
|
|
PF15 I2C4_SDA I2C4
|
|
|
|
|
|
|
|
|
|
# order of I2C buses
|
|
|
|
|
I2C_ORDER I2C3 I2C4 I2C1 I2C2
|
|
|
|
|
define HAL_I2C_INTERNAL_MASK 3
|
|
|
|
|
|
|
|
|
|
# enable sensors power pins
|
|
|
|
|
PI11 VDD_3V3_SENSORS_EN OUTPUT HIGH
|
|
|
|
|
PD15 VDD_3V3_SENSORS2_EN OUTPUT HIGH
|
|
|
|
|
PE7 VDD_3V3_SENSORS3_EN OUTPUT HIGH
|
|
|
|
|
PG8 VDD_3V3_SENSORS4_EN OUTPUT HIGH
|
|
|
|
|
|
2022-11-04 10:06:25 -03:00
|
|
|
# enable peripherals power pin
|
2022-04-18 07:31:18 -03:00
|
|
|
PF12 VDD_5V_HIPOWER_EN OUTPUT HIGH
|
2021-10-28 18:46:39 -03:00
|
|
|
|
2022-11-04 10:06:25 -03:00
|
|
|
# enable LTE module power pin
|
|
|
|
|
PG4 VDD_3V5_LTE_EN OUTPUT HIGH
|
|
|
|
|
|
2021-10-28 18:46:39 -03:00
|
|
|
# drdy pins
|
|
|
|
|
PF2 DRDY4_ICM20602 INPUT
|
|
|
|
|
PH12 MPU_FPC_DRDY INPUT
|
|
|
|
|
PI6 MPU_BOARD_DRDY INPUT
|
|
|
|
|
|
|
|
|
|
# UART for IOMCU
|
|
|
|
|
IOMCU_UART USART6
|
|
|
|
|
|
|
|
|
|
# UARTs
|
|
|
|
|
|
|
|
|
|
# USART2 is telem3
|
|
|
|
|
PA3 USART2_RX USART2 NODMA
|
|
|
|
|
PD5 USART2_TX USART2 NODMA
|
|
|
|
|
PD3 USART2_CTS USART2
|
|
|
|
|
PD4 USART2_RTS USART2
|
|
|
|
|
|
|
|
|
|
# USART1 is GPS1
|
|
|
|
|
PB15 USART1_RX USART1 NODMA
|
|
|
|
|
PB14 USART1_TX USART1 NODMA
|
|
|
|
|
|
|
|
|
|
# USART3 is debug
|
|
|
|
|
PD9 USART3_RX USART3 NODMA
|
|
|
|
|
PD8 USART3_TX USART3 NODMA
|
|
|
|
|
#PD11 USART3_CTS USART3
|
|
|
|
|
#PD12 USART3_RTS USART3
|
|
|
|
|
|
|
|
|
|
# UART4 is ext
|
|
|
|
|
PH14 UART4_RX UART4 NODMA
|
|
|
|
|
PH13 UART4_TX UART4 NODMA
|
|
|
|
|
|
|
|
|
|
# UART5 is telem2
|
|
|
|
|
PD2 UART5_RX UART5
|
|
|
|
|
PB9 UART5_TX UART5
|
|
|
|
|
|
|
|
|
|
# USART6 for IOMCU
|
|
|
|
|
PC7 USART6_RX USART6
|
|
|
|
|
PC6 USART6_TX USART6
|
|
|
|
|
|
|
|
|
|
# UART7 is telem1
|
|
|
|
|
PF6 UART7_RX UART7 NODMA
|
|
|
|
|
PE8 UART7_TX UART7 NODMA
|
|
|
|
|
|
|
|
|
|
# UART8 is for gps2
|
|
|
|
|
PE0 UART8_RX UART8 NODMA
|
|
|
|
|
PE1 UART8_TX UART8 NODMA
|
|
|
|
|
|
|
|
|
|
# PWM AUX channels
|
|
|
|
|
PE14 TIM1_CH4 TIM1 PWM(1) GPIO(50)
|
|
|
|
|
PA10 TIM1_CH3 TIM1 PWM(2) GPIO(51)
|
|
|
|
|
PE11 TIM1_CH2 TIM1 PWM(3) GPIO(52)
|
|
|
|
|
PA8 TIM1_CH1 TIM1 PWM(4) GPIO(53)
|
|
|
|
|
PD13 TIM4_CH2 TIM4 PWM(5) GPIO(54)
|
|
|
|
|
PD14 TIM4_CH3 TIM4 PWM(6) GPIO(55)
|
|
|
|
|
# we need to disable DMA on the last 2 FMU channels
|
|
|
|
|
# as timer 12 doesn't have a TIMn_UP DMA option
|
|
|
|
|
PH6 TIM12_CH1 TIM12 PWM(7) GPIO(56) NODMA
|
|
|
|
|
PH9 TIM12_CH2 TIM12 PWM(8) GPIO(57) NODMA
|
|
|
|
|
|
|
|
|
|
# PWM output for buzzer
|
|
|
|
|
PF9 TIM14_CH1 TIM14 GPIO(77) ALARM
|
|
|
|
|
|
|
|
|
|
# analog in
|
|
|
|
|
PC3 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
|
|
|
PC0 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
|
|
|
|
|
|
PB0 RSSI_IN ADC1 SCALE(1)
|
|
|
|
|
|
|
|
|
|
#PF5 HW_REV_SENS ADC3 SCALE(1)
|
|
|
|
|
#PF4 HW_VER_SENS ADC3 SCALE(1)
|
|
|
|
|
|
2022-01-23 06:56:21 -04:00
|
|
|
PB1 VDD_5V_SENS ADC1 SCALE(3)
|
2021-10-28 18:46:39 -03:00
|
|
|
PA0 SCALED_V3V3 ADC1 SCALE(2)
|
|
|
|
|
|
|
|
|
|
undef HAL_HAVE_SAFETY_SWITCH 0
|
|
|
|
|
|
|
|
|
|
# setup scaling defaults for power brick
|
|
|
|
|
define HAL_BATT_VOLT_SCALE 18.0
|
|
|
|
|
define HAL_BATT_CURR_SCALE 24.0
|
|
|
|
|
define HAL_BATT_VOLT_PIN 0
|
|
|
|
|
define HAL_BATT_CURR_PIN 1
|
|
|
|
|
|
|
|
|
|
# CAN bus
|
|
|
|
|
PD0 CAN1_RX CAN1
|
|
|
|
|
PD1 CAN1_TX CAN1
|
|
|
|
|
|
|
|
|
|
PB12 CAN2_RX CAN2
|
|
|
|
|
PB6 CAN2_TX CAN2
|
|
|
|
|
|
|
|
|
|
# GPIOs
|
|
|
|
|
PB10 HEATER_EN OUTPUT LOW GPIO(80)
|
|
|
|
|
define HAL_HEATER_GPIO_PIN 80
|
|
|
|
|
|
|
|
|
|
# heater is on when pulled low
|
|
|
|
|
define HAL_HEATER_GPIO_ON 0
|
2022-12-30 07:37:59 -04:00
|
|
|
define HAL_HAVE_IMU_HEATER 1
|
|
|
|
|
define HAL_IMU_TEMP_DEFAULT 45
|
|
|
|
|
define HAL_IMUHEAT_P_DEFAULT 50
|
|
|
|
|
define HAL_IMUHEAT_I_DEFAULT 0.07
|
2021-10-28 18:46:39 -03:00
|
|
|
|
|
|
|
|
# SPI devices
|
|
|
|
|
SPIDEV icm20602 SPI1 DEVID1 ICM20602_CS MODE3 2*MHZ 8*MHZ
|
|
|
|
|
SPIDEV mpu9250_fpc SPI2 DEVID1 MPU_FPC_CS MODE3 4*MHZ 8*MHZ
|
|
|
|
|
SPIDEV mpu9250_board SPI3 DEVID1 MPU_BOARD_CS MODE3 4*MHZ 8*MHZ
|
|
|
|
|
SPIDEV ramtron SPI5 DEVID1 FRAM_CS MODE3 8*MHZ 8*MHZ
|
|
|
|
|
|
|
|
|
|
# up to 3 IMUs
|
|
|
|
|
IMU Invensense SPI:icm20602 ROTATION_YAW_270
|
|
|
|
|
IMU Invensense SPI:mpu9250_fpc ROTATION_YAW_180
|
|
|
|
|
IMU Invensense SPI:mpu9250_board ROTATION_YAW_90
|
|
|
|
|
|
|
|
|
|
define HAL_DEFAULT_INS_FAST_SAMPLE 7
|
|
|
|
|
|
|
|
|
|
BARO MS56XX I2C:0:0x77
|
|
|
|
|
BARO BMP388 I2C:1:0x76
|
|
|
|
|
|
|
|
|
|
COMPASS AK8963:probe_mpu9250 0 ROTATION_NONE
|
|
|
|
|
COMPASS AK8963:probe_mpu9250 1 ROTATION_YAW_270
|
|
|
|
|
|
|
|
|
|
# also problem all external compass types
|
|
|
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
|
|
|
|
|
|
|
|
# microSD support
|
|
|
|
|
PG9 SDMMC2_D0 SDMMC2
|
|
|
|
|
PG10 SDMMC2_D1 SDMMC2
|
|
|
|
|
PG11 SDMMC2_D2 SDMMC2
|
|
|
|
|
PG12 SDMMC2_D3 SDMMC2
|
|
|
|
|
PD6 SDMMC2_CK SDMMC2
|
|
|
|
|
PD7 SDMMC2_CMD SDMMC2
|
|
|
|
|
|
|
|
|
|
# red LED marked as B/E
|
|
|
|
|
PE5 LED_RED OUTPUT OPENDRAIN GPIO(90)
|
|
|
|
|
|
|
|
|
|
# green LED marked as PWR. We leave this solid on, but allow
|
|
|
|
|
# for it to be controlled as a relay if needed
|
|
|
|
|
PE4 LED_GREEN OUTPUT GPIO(91) LOW
|
|
|
|
|
|
|
|
|
|
# blue LED marked as ACT
|
|
|
|
|
PE3 LED_BLUE OUTPUT GPIO(92) HIGH
|
|
|
|
|
|
|
|
|
|
# setup for BoardLED2
|
2024-07-09 00:19:56 -03:00
|
|
|
define AP_NOTIFY_GPIO_LED_2_ENABLED 1
|
2021-10-28 18:46:39 -03:00
|
|
|
define HAL_GPIO_A_LED_PIN 90
|
|
|
|
|
define HAL_GPIO_B_LED_PIN 92
|
|
|
|
|
|
|
|
|
|
# enable RAMTROM parameter storage
|
|
|
|
|
define HAL_STORAGE_SIZE 32768
|
|
|
|
|
define HAL_WITH_RAMTRON 1
|
|
|
|
|
|
|
|
|
|
define HAL_COMPASS_AUTO_ROT_DEFAULT 2
|
|
|
|
|
|
|
|
|
|
DMA_PRIORITY SDMMC* USART6* ADC* SPI* TIM*
|
|
|
|
|
|
|
|
|
|
# we can't share IO UART (USART6)
|
|
|
|
|
DMA_NOSHARE USART6_TX USART6_RX ADC1
|
|
|
|
|
DMA_PRIORITY USART6* UART5_RX
|
|
|
|
|
|
|
|
|
|
define FATFS_HAL_DEVICE SDCD2
|
|
|
|
|
|
|
|
|
|
# enable FAT filesystem support (needs a microSD defined via SDMMC)
|
|
|
|
|
define HAL_OS_FATFS_IO 1
|
|
|
|
|
|
|
|
|
|
ROMFS io_firmware.bin Tools/IO_Firmware/iofirmware_lowpolh.bin
|
