mirror of https://github.com/ArduPilot/ardupilot
66 lines
1.4 KiB
Plaintext
66 lines
1.4 KiB
Plaintext
|
# hw definition file for processing by chibios_pins.py
|
||
|
# for SP/Racing H7RF hardware.
|
||
|
|
||
|
# MCU class and specific type
|
||
|
MCU STM32H7xx STM32H730xx
|
||
|
|
||
|
# board ID for firmware load
|
||
|
APJ_BOARD_ID 1108
|
||
|
|
||
|
# crystal frequency, setup to use external oscillator
|
||
|
OSCILLATOR_HZ 8000000
|
||
|
|
||
|
MCU_CLOCKRATE_MHZ 520
|
||
|
|
||
|
# limited flash that can't be used
|
||
|
FLASH_SIZE_KB 128
|
||
|
FLASH_RESERVE_START_KB 0
|
||
|
FLASH_RESERVE_END_KB 0
|
||
|
FLASH_BOOTLOADER_LOAD_KB 128
|
||
|
|
||
|
# 16mb external flash
|
||
|
EXT_FLASH_SIZE_MB 2
|
||
|
|
||
|
# order of UARTs (and USB). Allow bootloading on USB and telem1
|
||
|
SERIAL_ORDER OTG1 USART1
|
||
|
|
||
|
# USART1
|
||
|
PB15 USART1_RX USART1
|
||
|
PB14 USART1_TX USART1
|
||
|
|
||
|
# USB
|
||
|
PA11 OTG_HS_DM OTG1
|
||
|
PA12 OTG_HS_DP OTG1
|
||
|
|
||
|
# Debug
|
||
|
PA13 JTMS-SWDIO SWD
|
||
|
PA14 JTCK-SWCLK SWD
|
||
|
|
||
|
PE3 LED_BOOTLOADER OUTPUT LOW # Red LED
|
||
|
define HAL_LED_ON 0
|
||
|
|
||
|
# OctoSPI Flash
|
||
|
PD11 OCTOSPIM_P1_IO0 OCTOSPI1
|
||
|
PD12 OCTOSPIM_P1_IO1 OCTOSPI1
|
||
|
PE2 OCTOSPIM_P1_IO2 OCTOSPI1
|
||
|
PD13 OCTOSPIM_P1_IO3 OCTOSPI1
|
||
|
PE7 OCTOSPIM_P1_IO4 OCTOSPI1
|
||
|
PE8 OCTOSPIM_P1_IO5 OCTOSPI1
|
||
|
PE9 OCTOSPIM_P1_IO6 OCTOSPI1
|
||
|
PE10 OCTOSPIM_P1_IO7 OCTOSPI1
|
||
|
PB6 OCTOSPIM_P1_NCS OCTOSPI1
|
||
|
PB2 OCTOSPIM_P1_CLK OCTOSPI1
|
||
|
|
||
|
# IFace Device Name Bus QSPI Mode Clk Freq Size (Pow2) NCS Delay
|
||
|
OSPIDEV w25q OCTOSPI1 MODE3 130*MHZ 21 1
|
||
|
|
||
|
define HAL_USE_EMPTY_STORAGE 1
|
||
|
define HAL_STORAGE_SIZE 16384
|
||
|
|
||
|
# Add CS pins to ensure they are high in bootloader
|
||
|
PA15 ICM42688_CS CS
|
||
|
PE11 PIXELOSD_CS CS
|
||
|
|
||
|
## pull up VTX power
|
||
|
PC15 VTX_PWR OUTPUT HIGH GPIO(81)
|