mirror of https://github.com/ArduPilot/ardupilot
59 lines
1.1 KiB
Plaintext
59 lines
1.1 KiB
Plaintext
|
# hw definition file for processing by chibios_hwdef.py
|
||
|
|
# for H743 bootloader
|
||
|
|
|
||
|
|
# MCU class and specific type
|
||
|
|
MCU STM32H7xx STM32H743xx
|
||
|
|
|
||
|
|
# crystal frequency
|
||
|
|
OSCILLATOR_HZ 16000000
|
||
|
|
|
||
|
|
# board ID for firmware load
|
||
|
|
APJ_BOARD_ID 5200
|
||
|
|
|
||
|
|
# the nucleo seems to have trouble with flashing the last sector?
|
||
|
|
FLASH_SIZE_KB 2048
|
||
|
|
|
||
|
|
# bootloader is installed at zero offset
|
||
|
|
FLASH_RESERVE_START_KB 0
|
||
|
|
|
||
|
|
# the location where the bootloader will put the firmware
|
||
|
|
# the H743 has 128k sectors
|
||
|
|
FLASH_BOOTLOADER_LOAD_KB 128
|
||
|
|
|
||
|
|
# USB setup
|
||
|
|
USB_STRING_MANUFACTURER "Airvolute"
|
||
|
|
|
||
|
|
# baudrate to run bootloader at on uarts
|
||
|
|
define BOOTLOADER_BAUDRATE 115200
|
||
|
|
|
||
|
|
# order of UARTs (and USB)
|
||
|
|
SERIAL_ORDER OTG1 USART1
|
||
|
|
|
||
|
|
# this is the pin that senses USB being connected. It is an input pin
|
||
|
|
# setup as OPENDRAIN
|
||
|
|
PA9 VBUS INPUT OPENDRAIN
|
||
|
|
|
||
|
|
# UART1 (SE_CONNECTOR)
|
||
|
|
PB14 USART1_TX USART1
|
||
|
|
PA10 USART1_RX USART1
|
||
|
|
|
||
|
|
PB1 LED_BOOTLOADER OUTPUT LOW
|
||
|
|
define HAL_LED_ON 1
|
||
|
|
|
||
|
|
define HAL_USE_SERIAL TRUE
|
||
|
|
|
||
|
|
PA11 OTG_FS_DM OTG1
|
||
|
|
PA12 OTG_FS_DP OTG1
|
||
|
|
|
||
|
|
PA13 JTMS-SWDIO SWD
|
||
|
|
PA14 JTCK-SWCLK SWD
|
||
|
|
|
||
|
|
# Add CS pins to ensure they are high in bootloader
|
||
|
|
PD12 IMU_CS0 CS
|
||
|
|
PE13 IMU_CS1 CS
|
||
|
|
PD13 BARO_CS CS
|
||
|
|
PD15 EXT_0 CS
|
||
|
|
PD14 EXT_1 CS
|
||
|
|
PD11 EXT_2 CS
|
||
|
|
PD10 EXT_3 CS
|