ardupilot/libraries/AP_Motors/AP_MotorsMatrix.cpp

706 lines
34 KiB
C++
Raw Normal View History

/*
This program is free software: you can redistribute it and/or modify
it under the terms of the GNU General Public License as published by
the Free Software Foundation, either version 3 of the License, or
(at your option) any later version.
This program is distributed in the hope that it will be useful,
but WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
GNU General Public License for more details.
You should have received a copy of the GNU General Public License
along with this program. If not, see <http://www.gnu.org/licenses/>.
*/
/*
* AP_MotorsMatrix.cpp - ArduCopter motors library
* Code by RandyMackay. DIYDrones.com
*
*/
#include <AP_HAL/AP_HAL.h>
#include "AP_MotorsMatrix.h"
2012-10-26 20:59:07 -03:00
extern const AP_HAL::HAL& hal;
// init
void AP_MotorsMatrix::init(motor_frame_class frame_class, motor_frame_type frame_type)
{
// record requested frame class and type
_last_frame_class = frame_class;
_last_frame_type = frame_type;
// setup the motors
setup_motors(frame_class, frame_type);
// enable fast channels or instant pwm
set_update_rate(_speed_hz);
}
// set update rate to motors - a value in hertz
void AP_MotorsMatrix::set_update_rate( uint16_t speed_hz )
{
// record requested speed
_speed_hz = speed_hz;
// we can use a mask of 0xFF here as rc_set_freq masks with actual
// motor mask
rc_set_freq(0xFF, _speed_hz );
}
// set frame class (i.e. quad, hexa, heli) and type (i.e. x, plus)
void AP_MotorsMatrix::set_frame_class_and_type(motor_frame_class frame_class, motor_frame_type frame_type)
{
// exit immediately if armed or no change
if (armed() || (frame_class == _last_frame_class && _last_frame_type == frame_type)) {
return;
}
_last_frame_class = frame_class;
_last_frame_type = frame_type;
// setup the motors
setup_motors(frame_class, frame_type);
// enable fast channels or instant pwm
set_update_rate(_speed_hz);
}
void AP_MotorsMatrix::output_to_motors()
{
int8_t i;
int16_t motor_out[AP_MOTORS_MAX_NUM_MOTORS]; // final pwm values sent to the motor
switch (_spool_mode) {
case SHUT_DOWN: {
// sends minimum values out to the motors
// set motor output based on thrust requests
for (i=0; i<AP_MOTORS_MAX_NUM_MOTORS; i++) {
if (motor_enabled[i]) {
if (_disarm_disable_pwm && _disarm_safety_timer == 0 && !armed()) {
motor_out[i] = 0;
} else {
motor_out[i] = get_pwm_output_min();
}
}
}
break;
}
case SPIN_WHEN_ARMED:
// sends output to motors when armed but not flying
for (i=0; i<AP_MOTORS_MAX_NUM_MOTORS; i++) {
if (motor_enabled[i]) {
motor_out[i] = calc_spin_up_to_pwm();
}
}
break;
case SPOOL_UP:
case THROTTLE_UNLIMITED:
case SPOOL_DOWN:
// set motor output based on thrust requests
for (i=0; i<AP_MOTORS_MAX_NUM_MOTORS; i++) {
if (motor_enabled[i]) {
motor_out[i] = calc_thrust_to_pwm(_thrust_rpyt_out[i]);
}
}
break;
}
// send output to each motor
for (i=0; i<AP_MOTORS_MAX_NUM_MOTORS; i++) {
if (motor_enabled[i]) {
rc_write(i, motor_out[i]);
}
}
}
2014-07-26 04:29:48 -03:00
// get_motor_mask - returns a bitmask of which outputs are being used for motors (1 means being used)
// this can be used to ensure other pwm outputs (i.e. for servos) do not conflict
uint16_t AP_MotorsMatrix::get_motor_mask()
{
uint16_t mask = 0;
for (uint8_t i=0; i<AP_MOTORS_MAX_NUM_MOTORS; i++) {
if (motor_enabled[i]) {
mask |= 1U << i;
}
}
return rc_map_mask(mask);
2014-07-26 04:29:48 -03:00
}
2013-05-26 23:21:31 -03:00
// output_armed - sends commands to the motors
// includes new scaling stability patch
void AP_MotorsMatrix::output_armed_stabilizing()
2013-05-26 23:21:31 -03:00
{
uint8_t i; // general purpose counter
float roll_thrust; // roll thrust input value, +/- 1.0
float pitch_thrust; // pitch thrust input value, +/- 1.0
float yaw_thrust; // yaw thrust input value, +/- 1.0
float throttle_thrust; // throttle thrust input value, 0.0 - 1.0
2017-10-04 08:36:43 -03:00
float throttle_avg_max; // throttle thrust average maximum value, 0.0 - 1.0
float throttle_thrust_best_rpy; // throttle providing maximum roll, pitch and yaw range without climbing
float rpy_scale = 1.0f; // this is used to scale the roll, pitch and yaw to fit within the motor limits
float rpy_low = 0.0f; // lowest motor value
float rpy_high = 0.0f; // highest motor value
float yaw_allowed = 1.0f; // amount of yaw we can fit in
float unused_range; // amount of yaw we can fit in the current channel
float thr_adj; // the difference between the pilot's desired throttle and throttle_thrust_best_rpy
// apply voltage and air pressure compensation
const float compensation_gain = get_compensation_gain();
roll_thrust = _roll_in * compensation_gain;
pitch_thrust = _pitch_in * compensation_gain;
yaw_thrust = _yaw_in * compensation_gain;
throttle_thrust = get_throttle() * compensation_gain;
throttle_avg_max = _throttle_avg_max * compensation_gain;
// sanity check throttle is above zero and below current limited throttle
if (throttle_thrust <= 0.0f) {
throttle_thrust = 0.0f;
limit.throttle_lower = true;
}
if (throttle_thrust >= _throttle_thrust_max) {
throttle_thrust = _throttle_thrust_max;
limit.throttle_upper = true;
}
2013-05-26 23:21:31 -03:00
2017-10-04 08:36:43 -03:00
throttle_avg_max = constrain_float(throttle_avg_max, throttle_thrust, _throttle_thrust_max);
2013-05-26 23:21:31 -03:00
// calculate throttle that gives most possible room for yaw which is the lower of:
// 1. 0.5f - (rpy_low+rpy_high)/2.0 - this would give the maximum possible margin above the highest motor and below the lowest
// 2. the higher of:
// a) the pilot's throttle input
// b) the point _throttle_rpy_mix between the pilot's input throttle and hover-throttle
// Situation #2 ensure we never increase the throttle above hover throttle unless the pilot has commanded this.
// Situation #2b allows us to raise the throttle above what the pilot commanded but not so far that it would actually cause the copter to rise.
// We will choose #1 (the best throttle for yaw control) if that means reducing throttle to the motors (i.e. we favor reducing throttle *because* it provides better yaw control)
// We will choose #2 (a mix of pilot and hover throttle) only when the throttle is quite low. We favor reducing throttle instead of better yaw control because the pilot has commanded it
// calculate amount of yaw we can fit into the throttle range
// this is always equal to or less than the requested yaw from the pilot or rate controller
2017-10-04 08:36:43 -03:00
throttle_thrust_best_rpy = MIN(0.5f, throttle_avg_max);
// calculate roll and pitch for each motor
// calculate the amount of yaw input that each motor can accept
for (i=0; i<AP_MOTORS_MAX_NUM_MOTORS; i++) {
if (motor_enabled[i]) {
_thrust_rpyt_out[i] = roll_thrust * _roll_factor[i] + pitch_thrust * _pitch_factor[i];
if (!is_zero(_yaw_factor[i])){
if (yaw_thrust * _yaw_factor[i] > 0.0f) {
2017-10-04 08:36:43 -03:00
unused_range = fabsf(MAX(1.0f - (throttle_thrust_best_rpy + _thrust_rpyt_out[i]), 0.0f)/_yaw_factor[i]);
if (yaw_allowed > unused_range) {
yaw_allowed = unused_range;
}
} else {
2017-10-04 08:36:43 -03:00
unused_range = fabsf(MAX(throttle_thrust_best_rpy + _thrust_rpyt_out[i], 0.0f)/_yaw_factor[i]);
if (yaw_allowed > unused_range) {
yaw_allowed = unused_range;
}
}
}
2013-05-26 23:21:31 -03:00
}
}
2013-05-26 23:21:31 -03:00
// todo: make _yaw_headroom 0 to 1
yaw_allowed = MAX(yaw_allowed, (float)_yaw_headroom/1000.0f);
if (fabsf(yaw_thrust) > yaw_allowed) {
yaw_thrust = constrain_float(yaw_thrust, -yaw_allowed, yaw_allowed);
limit.yaw = true;
}
// add yaw to intermediate numbers for each motor
rpy_low = 0.0f;
rpy_high = 0.0f;
for (i=0; i<AP_MOTORS_MAX_NUM_MOTORS; i++) {
if (motor_enabled[i]) {
_thrust_rpyt_out[i] = _thrust_rpyt_out[i] + yaw_thrust * _yaw_factor[i];
2013-05-26 23:21:31 -03:00
// record lowest roll+pitch+yaw command
if (_thrust_rpyt_out[i] < rpy_low) {
rpy_low = _thrust_rpyt_out[i];
2013-05-26 23:21:31 -03:00
}
// record highest roll+pitch+yaw command
if (_thrust_rpyt_out[i] > rpy_high) {
rpy_high = _thrust_rpyt_out[i];
}
2013-05-26 23:21:31 -03:00
}
}
2013-05-26 23:21:31 -03:00
// check everything fits
2017-10-04 08:36:43 -03:00
throttle_thrust_best_rpy = MIN(0.5f - (rpy_low+rpy_high)/2.0, throttle_avg_max);
if (is_zero(rpy_low) && is_zero(rpy_high)){
rpy_scale = 1.0f;
2017-10-04 08:36:43 -03:00
} else if (is_zero(rpy_low)) {
rpy_scale = constrain_float((1.0f-throttle_thrust_best_rpy)/rpy_high, 0.0f, 1.0f);
} else if (is_zero(rpy_high)) {
rpy_scale = constrain_float(-throttle_thrust_best_rpy/rpy_low, 0.0f, 1.0f);
2017-10-04 08:36:43 -03:00
} else {
rpy_scale = constrain_float(MIN(-throttle_thrust_best_rpy/rpy_low, (1.0f-throttle_thrust_best_rpy)/rpy_high), 0.0f, 1.0f);
}
2013-05-26 23:21:31 -03:00
// calculate how close the motors can come to the desired throttle
thr_adj = throttle_thrust - throttle_thrust_best_rpy;
if (rpy_scale < 1.0f){
// Full range is being used by roll, pitch, and yaw.
limit.roll_pitch = true;
limit.yaw = true;
if (thr_adj > 0.0f) {
limit.throttle_upper = true;
}
thr_adj = 0.0f;
} else {
if (thr_adj < -(throttle_thrust_best_rpy+rpy_low)){
// Throttle can't be reduced to desired value
thr_adj = -(throttle_thrust_best_rpy+rpy_low);
} else if (thr_adj > 1.0f - (throttle_thrust_best_rpy+rpy_high)){
// Throttle can't be increased to desired value
thr_adj = 1.0f - (throttle_thrust_best_rpy+rpy_high);
limit.throttle_upper = true;
2013-05-26 23:21:31 -03:00
}
}
2013-05-26 23:21:31 -03:00
// add scaled roll, pitch, constrained yaw and throttle for each motor
for (i=0; i<AP_MOTORS_MAX_NUM_MOTORS; i++) {
if (motor_enabled[i]) {
_thrust_rpyt_out[i] = throttle_thrust_best_rpy + thr_adj + rpy_scale*_thrust_rpyt_out[i];
2013-05-26 23:21:31 -03:00
}
}
// constrain all outputs to 0.0f to 1.0f
// test code should be run with these lines commented out as they should not do anything
for (i=0; i<AP_MOTORS_MAX_NUM_MOTORS; i++) {
if (motor_enabled[i]) {
_thrust_rpyt_out[i] = constrain_float(_thrust_rpyt_out[i], 0.0f, 1.0f);
2013-05-26 23:21:31 -03:00
}
}
}
// output_test - spin a motor at the pwm value specified
// motor_seq is the motor's sequence number from 1 to the number of motors on the frame
// pwm value is an actual pwm value that will be output, normally in the range of 1000 ~ 2000
void AP_MotorsMatrix::output_test(uint8_t motor_seq, int16_t pwm)
{
// exit immediately if not armed
if (!armed()) {
return;
}
// loop through all the possible orders spinning any motors that match that description
for (uint8_t i=0; i<AP_MOTORS_MAX_NUM_MOTORS; i++) {
if (motor_enabled[i] && _test_order[i] == motor_seq) {
// turn on this motor
rc_write(i, pwm);
}
}
}
// add_motor
2013-05-14 06:03:34 -03:00
void AP_MotorsMatrix::add_motor_raw(int8_t motor_num, float roll_fac, float pitch_fac, float yaw_fac, uint8_t testing_order)
{
// ensure valid motor number is provided
if( motor_num >= 0 && motor_num < AP_MOTORS_MAX_NUM_MOTORS ) {
// increment number of motors if this motor is being newly motor_enabled
if( !motor_enabled[motor_num] ) {
motor_enabled[motor_num] = true;
}
// set roll, pitch, thottle factors and opposite motor (for stability patch)
_roll_factor[motor_num] = roll_fac;
_pitch_factor[motor_num] = pitch_fac;
_yaw_factor[motor_num] = yaw_fac;
// set order that motor appears in test
2013-05-14 06:03:34 -03:00
_test_order[motor_num] = testing_order;
// call parent class method
add_motor_num(motor_num);
}
}
// add_motor using just position and prop direction - assumes that for each motor, roll and pitch factors are equal
2013-05-14 06:03:34 -03:00
void AP_MotorsMatrix::add_motor(int8_t motor_num, float angle_degrees, float yaw_factor, uint8_t testing_order)
{
add_motor(motor_num, angle_degrees, angle_degrees, yaw_factor, testing_order);
}
// add_motor using position and prop direction. Roll and Pitch factors can differ (for asymmetrical frames)
void AP_MotorsMatrix::add_motor(int8_t motor_num, float roll_factor_in_degrees, float pitch_factor_in_degrees, float yaw_factor, uint8_t testing_order)
{
add_motor_raw(
motor_num,
cosf(radians(roll_factor_in_degrees + 90)),
cosf(radians(pitch_factor_in_degrees)),
yaw_factor,
testing_order);
}
// remove_motor - disabled motor and clears all roll, pitch, throttle factors for this motor
void AP_MotorsMatrix::remove_motor(int8_t motor_num)
{
// ensure valid motor number is provided
if( motor_num >= 0 && motor_num < AP_MOTORS_MAX_NUM_MOTORS ) {
// disable the motor, set all factors to zero
motor_enabled[motor_num] = false;
_roll_factor[motor_num] = 0;
_pitch_factor[motor_num] = 0;
_yaw_factor[motor_num] = 0;
}
}
void AP_MotorsMatrix::setup_motors(motor_frame_class frame_class, motor_frame_type frame_type)
{
// remove existing motors
for (int8_t i=0; i<AP_MOTORS_MAX_NUM_MOTORS; i++) {
remove_motor(i);
}
bool success = false;
switch (frame_class) {
case MOTOR_FRAME_QUAD:
switch (frame_type) {
case MOTOR_FRAME_TYPE_PLUS:
add_motor(AP_MOTORS_MOT_1, 90, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 2);
add_motor(AP_MOTORS_MOT_2, -90, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 4);
add_motor(AP_MOTORS_MOT_3, 0, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 1);
add_motor(AP_MOTORS_MOT_4, 180, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 3);
success = true;
break;
case MOTOR_FRAME_TYPE_X:
add_motor(AP_MOTORS_MOT_1, 45, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 1);
add_motor(AP_MOTORS_MOT_2, -135, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 3);
add_motor(AP_MOTORS_MOT_3, -45, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 4);
add_motor(AP_MOTORS_MOT_4, 135, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 2);
success = true;
break;
case MOTOR_FRAME_TYPE_V:
add_motor(AP_MOTORS_MOT_1, 45, 0.7981f, 1);
add_motor(AP_MOTORS_MOT_2, -135, 1.0000f, 3);
add_motor(AP_MOTORS_MOT_3, -45, -0.7981f, 4);
add_motor(AP_MOTORS_MOT_4, 135, -1.0000f, 2);
success = true;
break;
case MOTOR_FRAME_TYPE_H:
// H frame set-up - same as X but motors spin in opposite directiSons
add_motor(AP_MOTORS_MOT_1, 45, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 1);
add_motor(AP_MOTORS_MOT_2, -135, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 3);
add_motor(AP_MOTORS_MOT_3, -45, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 4);
add_motor(AP_MOTORS_MOT_4, 135, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 2);
success = true;
break;
case MOTOR_FRAME_TYPE_VTAIL:
/*
Tested with: Lynxmotion Hunter Vtail 400
- inverted rear outward blowing motors (at a 40 degree angle)
- should also work with non-inverted rear outward blowing motors
- no roll in rear motors
- no yaw in front motors
- should fly like some mix between a tricopter and X Quadcopter
Roll control comes only from the front motors, Yaw control only from the rear motors.
Roll & Pitch factor is measured by the angle away from the top of the forward axis to each arm.
Note: if we want the front motors to help with yaw,
motors 1's yaw factor should be changed to sin(radians(40)). Where "40" is the vtail angle
motors 3's yaw factor should be changed to -sin(radians(40))
*/
add_motor(AP_MOTORS_MOT_1, 60, 60, 0, 1);
add_motor(AP_MOTORS_MOT_2, 0, -160, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 3);
add_motor(AP_MOTORS_MOT_3, -60, -60, 0, 4);
add_motor(AP_MOTORS_MOT_4, 0, 160, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 2);
success = true;
break;
case MOTOR_FRAME_TYPE_ATAIL:
/*
The A-Shaped VTail is the exact same as a V-Shaped VTail, with one difference:
- The Yaw factors are reversed, because the rear motors are facing different directions
With V-Shaped VTails, the props make a V-Shape when spinning, but with
A-Shaped VTails, the props make an A-Shape when spinning.
- Rear thrust on a V-Shaped V-Tail Quad is outward
- Rear thrust on an A-Shaped V-Tail Quad is inward
Still functions the same as the V-Shaped VTail mixing below:
- Yaw control is entirely in the rear motors
- Roll is is entirely in the front motors
*/
add_motor(AP_MOTORS_MOT_1, 60, 60, 0, 1);
add_motor(AP_MOTORS_MOT_2, 0, -160, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 3);
add_motor(AP_MOTORS_MOT_3, -60, -60, 0, 4);
add_motor(AP_MOTORS_MOT_4, 0, 160, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 2);
success = true;
break;
default:
// quad frame class does not support this frame type
break;
}
break; // quad
case MOTOR_FRAME_HEXA:
switch (frame_type) {
case MOTOR_FRAME_TYPE_PLUS:
add_motor(AP_MOTORS_MOT_1, 0, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 1);
add_motor(AP_MOTORS_MOT_2, 180, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 4);
add_motor(AP_MOTORS_MOT_3,-120, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 5);
add_motor(AP_MOTORS_MOT_4, 60, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 2);
add_motor(AP_MOTORS_MOT_5, -60, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 6);
add_motor(AP_MOTORS_MOT_6, 120, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 3);
success = true;
break;
case MOTOR_FRAME_TYPE_X:
add_motor(AP_MOTORS_MOT_1, 90, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 2);
add_motor(AP_MOTORS_MOT_2, -90, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 5);
add_motor(AP_MOTORS_MOT_3, -30, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 6);
add_motor(AP_MOTORS_MOT_4, 150, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 3);
add_motor(AP_MOTORS_MOT_5, 30, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 1);
add_motor(AP_MOTORS_MOT_6,-150, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 4);
success = true;
break;
default:
// hexa frame class does not support this frame type
break;
}
break;
case MOTOR_FRAME_OCTA:
switch (frame_type) {
case MOTOR_FRAME_TYPE_PLUS:
add_motor(AP_MOTORS_MOT_1, 0, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 1);
add_motor(AP_MOTORS_MOT_2, 180, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 5);
add_motor(AP_MOTORS_MOT_3, 45, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 2);
add_motor(AP_MOTORS_MOT_4, 135, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 4);
add_motor(AP_MOTORS_MOT_5, -45, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 8);
add_motor(AP_MOTORS_MOT_6, -135, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 6);
add_motor(AP_MOTORS_MOT_7, -90, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 7);
add_motor(AP_MOTORS_MOT_8, 90, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 3);
success = true;
break;
case MOTOR_FRAME_TYPE_X:
add_motor(AP_MOTORS_MOT_1, 22.5f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 1);
add_motor(AP_MOTORS_MOT_2, -157.5f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 5);
add_motor(AP_MOTORS_MOT_3, 67.5f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 2);
add_motor(AP_MOTORS_MOT_4, 157.5f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 4);
add_motor(AP_MOTORS_MOT_5, -22.5f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 8);
add_motor(AP_MOTORS_MOT_6, -112.5f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 6);
add_motor(AP_MOTORS_MOT_7, -67.5f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 7);
add_motor(AP_MOTORS_MOT_8, 112.5f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 3);
success = true;
break;
case MOTOR_FRAME_TYPE_V:
add_motor_raw(AP_MOTORS_MOT_1, 1.0f, 0.34f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 7);
add_motor_raw(AP_MOTORS_MOT_2, -1.0f, -0.32f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 3);
add_motor_raw(AP_MOTORS_MOT_3, 1.0f, -0.32f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 6);
add_motor_raw(AP_MOTORS_MOT_4, -0.5f, -1.0f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 4);
add_motor_raw(AP_MOTORS_MOT_5, 1.0f, 1.0f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 8);
add_motor_raw(AP_MOTORS_MOT_6, -1.0f, 0.34f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 2);
add_motor_raw(AP_MOTORS_MOT_7, -1.0f, 1.0f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 1);
add_motor_raw(AP_MOTORS_MOT_8, 0.5f, -1.0f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 5);
success = true;
break;
case MOTOR_FRAME_TYPE_H:
add_motor_raw(AP_MOTORS_MOT_1, -1.0f, 1.0f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 1);
add_motor_raw(AP_MOTORS_MOT_2, 1.0f, -1.0f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 5);
add_motor_raw(AP_MOTORS_MOT_3, -1.0f, 0.333f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 2);
add_motor_raw(AP_MOTORS_MOT_4, -1.0f, -1.0f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 4);
add_motor_raw(AP_MOTORS_MOT_5, 1.0f, 1.0f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 8);
add_motor_raw(AP_MOTORS_MOT_6, 1.0f, -0.333f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 6);
add_motor_raw(AP_MOTORS_MOT_7, 1.0f, 0.333f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 7);
add_motor_raw(AP_MOTORS_MOT_8, -1.0f, -0.333f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 3);
success = true;
break;
default:
// octa frame class does not support this frame type
break;
} // octa frame type
break;
case MOTOR_FRAME_OCTAQUAD:
switch (frame_type) {
case MOTOR_FRAME_TYPE_PLUS:
add_motor(AP_MOTORS_MOT_1, 0, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 1);
add_motor(AP_MOTORS_MOT_2, -90, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 7);
add_motor(AP_MOTORS_MOT_3, 180, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 5);
add_motor(AP_MOTORS_MOT_4, 90, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 3);
add_motor(AP_MOTORS_MOT_5, -90, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 8);
add_motor(AP_MOTORS_MOT_6, 0, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 2);
add_motor(AP_MOTORS_MOT_7, 90, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 4);
add_motor(AP_MOTORS_MOT_8, 180, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 6);
success = true;
break;
case MOTOR_FRAME_TYPE_X:
add_motor(AP_MOTORS_MOT_1, 45, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 1);
add_motor(AP_MOTORS_MOT_2, -45, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 7);
add_motor(AP_MOTORS_MOT_3, -135, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 5);
add_motor(AP_MOTORS_MOT_4, 135, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 3);
add_motor(AP_MOTORS_MOT_5, -45, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 8);
add_motor(AP_MOTORS_MOT_6, 45, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 2);
add_motor(AP_MOTORS_MOT_7, 135, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 4);
add_motor(AP_MOTORS_MOT_8, -135, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 6);
success = true;
break;
case MOTOR_FRAME_TYPE_V:
add_motor(AP_MOTORS_MOT_1, 45, 0.7981f, 1);
add_motor(AP_MOTORS_MOT_2, -45, -0.7981f, 7);
add_motor(AP_MOTORS_MOT_3, -135, 1.0000f, 5);
add_motor(AP_MOTORS_MOT_4, 135, -1.0000f, 3);
add_motor(AP_MOTORS_MOT_5, -45, 0.7981f, 8);
add_motor(AP_MOTORS_MOT_6, 45, -0.7981f, 2);
add_motor(AP_MOTORS_MOT_7, 135, 1.0000f, 4);
add_motor(AP_MOTORS_MOT_8, -135, -1.0000f, 6);
success = true;
break;
case MOTOR_FRAME_TYPE_H:
// H frame set-up - same as X but motors spin in opposite directions
add_motor(AP_MOTORS_MOT_1, 45, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 1);
add_motor(AP_MOTORS_MOT_2, -45, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 7);
add_motor(AP_MOTORS_MOT_3, -135, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 5);
add_motor(AP_MOTORS_MOT_4, 135, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 3);
add_motor(AP_MOTORS_MOT_5, -45, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 8);
add_motor(AP_MOTORS_MOT_6, 45, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 2);
add_motor(AP_MOTORS_MOT_7, 135, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 4);
add_motor(AP_MOTORS_MOT_8, -135, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 6);
success = true;
break;
default:
// octaquad frame class does not support this frame type
break;
}
break;
2017-05-13 22:15:49 -03:00
case MOTOR_FRAME_DODECAHEXA: {
switch (frame_type) {
case MOTOR_FRAME_TYPE_PLUS:
add_motor(AP_MOTORS_MOT_1, 0, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 1); // forward-top
add_motor(AP_MOTORS_MOT_2, 0, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 2); // forward-bottom
add_motor(AP_MOTORS_MOT_3, 60, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 3); // forward-right-top
add_motor(AP_MOTORS_MOT_4, 60, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 4); // forward-right-bottom
add_motor(AP_MOTORS_MOT_5, 120, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 5); // back-right-top
add_motor(AP_MOTORS_MOT_6, 120, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 6); // back-right-bottom
add_motor(AP_MOTORS_MOT_7, 180, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 7); // back-top
add_motor(AP_MOTORS_MOT_8, 180, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 8); // back-bottom
add_motor(AP_MOTORS_MOT_9, -120, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 9); // back-left-top
add_motor(AP_MOTORS_MOT_10, -120, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 10); // back-left-bottom
add_motor(AP_MOTORS_MOT_11, -60, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 11); // forward-left-top
add_motor(AP_MOTORS_MOT_12, -60, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 12); // forward-left-bottom
success = true;
break;
case MOTOR_FRAME_TYPE_X:
add_motor(AP_MOTORS_MOT_1, 30, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 1); // forward-right-top
add_motor(AP_MOTORS_MOT_2, 30, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 2); // forward-right-bottom
add_motor(AP_MOTORS_MOT_3, 90, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 3); // right-top
add_motor(AP_MOTORS_MOT_4, 90, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 4); // right-bottom
add_motor(AP_MOTORS_MOT_5, 150, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 5); // back-right-top
add_motor(AP_MOTORS_MOT_6, 150, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 6); // back-right-bottom
add_motor(AP_MOTORS_MOT_7, -150, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 7); // back-left-top
add_motor(AP_MOTORS_MOT_8, -150, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 8); // back-left-bottom
add_motor(AP_MOTORS_MOT_9, -90, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 9); // left-top
add_motor(AP_MOTORS_MOT_10, -90, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 10); // left-bottom
add_motor(AP_MOTORS_MOT_11, -30, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 11); // forward-left-top
add_motor(AP_MOTORS_MOT_12, -30, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 12); // forward-left-bottom
success = true;
break;
default:
// dodeca-hexa frame class does not support this frame type
break;
}}
break;
case MOTOR_FRAME_Y6:
switch (frame_type) {
case MOTOR_FRAME_TYPE_Y6B:
// Y6 motor definition with all top motors spinning clockwise, all bottom motors counter clockwise
add_motor_raw(AP_MOTORS_MOT_1, -1.0f, 0.500f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 1);
add_motor_raw(AP_MOTORS_MOT_2, -1.0f, 0.500f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 2);
add_motor_raw(AP_MOTORS_MOT_3, 0.0f, -1.000f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 3);
add_motor_raw(AP_MOTORS_MOT_4, 0.0f, -1.000f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 4);
add_motor_raw(AP_MOTORS_MOT_5, 1.0f, 0.500f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 5);
add_motor_raw(AP_MOTORS_MOT_6, 1.0f, 0.500f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 6);
success = true;
break;
case MOTOR_FRAME_TYPE_Y6F:
// Y6 motor layout for FireFlyY6
add_motor_raw(AP_MOTORS_MOT_1, 0.0f, -1.000f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 3);
add_motor_raw(AP_MOTORS_MOT_2, -1.0f, 0.500f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 1);
add_motor_raw(AP_MOTORS_MOT_3, 1.0f, 0.500f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 5);
add_motor_raw(AP_MOTORS_MOT_4, 0.0f, -1.000f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 4);
add_motor_raw(AP_MOTORS_MOT_5, -1.0f, 0.500f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 2);
add_motor_raw(AP_MOTORS_MOT_6, 1.0f, 0.500f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 6);
success = true;
break;
default:
add_motor_raw(AP_MOTORS_MOT_1, -1.0f, 0.666f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 2);
add_motor_raw(AP_MOTORS_MOT_2, 1.0f, 0.666f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 5);
add_motor_raw(AP_MOTORS_MOT_3, 1.0f, 0.666f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 6);
add_motor_raw(AP_MOTORS_MOT_4, 0.0f, -1.333f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 4);
add_motor_raw(AP_MOTORS_MOT_5, -1.0f, 0.666f, AP_MOTORS_MATRIX_YAW_FACTOR_CW, 1);
add_motor_raw(AP_MOTORS_MOT_6, 0.0f, -1.333f, AP_MOTORS_MATRIX_YAW_FACTOR_CCW, 3);
success = true;
break;
}
break;
default:
// matrix doesn't support the configured class
break;
} // switch frame_class
// normalise factors to magnitude 0.5
normalise_rpy_factors();
_flags.initialised_ok = success;
2012-10-26 20:59:07 -03:00
}
// normalizes the roll, pitch and yaw factors so maximum magnitude is 0.5
void AP_MotorsMatrix::normalise_rpy_factors()
{
float roll_fac = 0.0f;
float pitch_fac = 0.0f;
float yaw_fac = 0.0f;
// find maximum roll, pitch and yaw factors
for (uint8_t i=0; i<AP_MOTORS_MAX_NUM_MOTORS; i++) {
if (motor_enabled[i]) {
if (roll_fac < fabsf(_roll_factor[i])) {
roll_fac = fabsf(_roll_factor[i]);
}
if (pitch_fac < fabsf(_pitch_factor[i])) {
pitch_fac = fabsf(_pitch_factor[i]);
}
if (yaw_fac < fabsf(_yaw_factor[i])) {
yaw_fac = fabsf(_yaw_factor[i]);
}
}
}
// scale factors back to -0.5 to +0.5 for each axis
for (uint8_t i=0; i<AP_MOTORS_MAX_NUM_MOTORS; i++) {
if (motor_enabled[i]) {
if (!is_zero(roll_fac)) {
_roll_factor[i] = 0.5f*_roll_factor[i]/roll_fac;
}
if (!is_zero(pitch_fac)) {
_pitch_factor[i] = 0.5f*_pitch_factor[i]/pitch_fac;
}
if (!is_zero(yaw_fac)) {
_yaw_factor[i] = 0.5f*_yaw_factor[i]/yaw_fac;
}
}
}
}
/*
call vehicle supplied thrust compensation if set. This allows
vehicle code to compensate for vehicle specific motor arrangements
such as tiltrotors or tiltwings
*/
void AP_MotorsMatrix::thrust_compensation(void)
{
if (_thrust_compensation_callback) {
_thrust_compensation_callback(_thrust_rpyt_out, AP_MOTORS_MAX_NUM_MOTORS);
}
}