2024-07-06 11:37:43 -03:00
|
|
|
# hw definition file for LongBow F4 WING hardware
|
|
|
|
|
# tested on the LongBow F405 WING board
|
|
|
|
|
#
|
|
|
|
|
|
|
|
|
|
# MCU class and specific type
|
|
|
|
|
MCU STM32F4xx STM32F405xx
|
|
|
|
|
|
|
|
|
|
# board ID for firmware load
|
|
|
|
|
APJ_BOARD_ID AP_HW_LongbowF405
|
|
|
|
|
|
|
|
|
|
# crystal frequency
|
|
|
|
|
OSCILLATOR_HZ 8000000
|
|
|
|
|
|
|
|
|
|
define STM32_ST_USE_TIMER 5
|
|
|
|
|
define CH_CFG_ST_RESOLUTION 32
|
|
|
|
|
|
|
|
|
|
# reserve 16k for bootloader, 16k for OSD and 32k for flash storage
|
|
|
|
|
FLASH_RESERVE_START_KB 64
|
|
|
|
|
FLASH_SIZE_KB 1024
|
|
|
|
|
|
|
|
|
|
define HAL_STORAGE_SIZE 15360
|
|
|
|
|
STORAGE_FLASH_PAGE 1
|
|
|
|
|
|
|
|
|
|
# only one I2C bus
|
|
|
|
|
I2C_ORDER I2C1
|
|
|
|
|
|
|
|
|
|
# order of UARTs (and USB)
|
|
|
|
|
SERIAL_ORDER OTG1 USART1 USART2 USART3 UART4 UART5 USART6
|
|
|
|
|
|
|
|
|
|
# LEDs
|
2024-07-09 00:19:56 -03:00
|
|
|
define AP_NOTIFY_GPIO_LED_2_ENABLED 1
|
|
|
|
|
|
2024-07-06 11:37:43 -03:00
|
|
|
PA13 LED_GREEN OUTPUT LOW GPIO(0)
|
|
|
|
|
PA14 LED_BLUE OUTPUT LOW GPIO(1)
|
|
|
|
|
|
|
|
|
|
define HAL_GPIO_A_LED_PIN 0
|
|
|
|
|
define HAL_GPIO_B_LED_PIN 1
|
|
|
|
|
|
|
|
|
|
# buzzer
|
|
|
|
|
PC15 BUZZER OUTPUT GPIO(80) LOW
|
|
|
|
|
define HAL_BUZZER_PIN 80
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
# spi1 bus for IMU
|
|
|
|
|
PA5 SPI1_SCK SPI1
|
|
|
|
|
PA6 SPI1_MISO SPI1
|
|
|
|
|
PA7 SPI1_MOSI SPI1
|
|
|
|
|
PA4 MPU_CS CS
|
|
|
|
|
|
|
|
|
|
# spi2 for OSD
|
|
|
|
|
PB13 SPI2_SCK SPI2
|
|
|
|
|
PC2 SPI2_MISO SPI2
|
|
|
|
|
PC3 SPI2_MOSI SPI2
|
|
|
|
|
PB12 OSD_CS CS
|
|
|
|
|
|
|
|
|
|
# spi3 for sdcard
|
|
|
|
|
PB3 SPI3_SCK SPI3
|
|
|
|
|
PB4 SPI3_MISO SPI3
|
|
|
|
|
PB5 SPI3_MOSI SPI3
|
|
|
|
|
PC14 SDCARD_CS CS
|
|
|
|
|
|
|
|
|
|
# only one I2C bus in normal config
|
|
|
|
|
PB8 I2C1_SCL I2C1
|
|
|
|
|
PB9 I2C1_SDA I2C1
|
|
|
|
|
|
|
|
|
|
# analog pins
|
|
|
|
|
PC0 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
|
|
|
PC1 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
|
PC4 RSSI_ADC_PIN ADC1 SCALE(1)
|
|
|
|
|
|
|
|
|
|
PC5 PRESSURE_SENS ADC1 SCALE(1)
|
|
|
|
|
define HAL_DEFAULT_AIRSPEED_PIN 15
|
|
|
|
|
|
|
|
|
|
# define default battery setup
|
|
|
|
|
define HAL_BATT_MONITOR_DEFAULT 4
|
|
|
|
|
define HAL_BATT_VOLT_PIN 10
|
|
|
|
|
define HAL_BATT_CURR_PIN 11
|
|
|
|
|
define HAL_BATT_VOLT_SCALE 11.0 # matched to PDB board
|
|
|
|
|
define HAL_BATT_CURR_SCALE 50 # matched to PDB board
|
|
|
|
|
|
|
|
|
|
# analog rssi pin
|
|
|
|
|
define BOARD_RSSI_ANA_PIN 14
|
|
|
|
|
|
|
|
|
|
# USART1 (ELRS)
|
|
|
|
|
PA9 USART1_TX USART1
|
|
|
|
|
PA10 USART1_RX USART1
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
# USART2 (RCIN with inverter)
|
|
|
|
|
|
|
|
|
|
PA3 TIM9_CH2 TIM9 RCININT PULLDOWN LOW
|
|
|
|
|
|
|
|
|
|
# alternative with PA3 as USART2_RX
|
|
|
|
|
PA2 USART2_TX USART2 NODMA
|
|
|
|
|
PA3 USART2_RX USART2 NODMA ALT(1)
|
|
|
|
|
|
|
|
|
|
# USART3 (GPS)
|
|
|
|
|
PC10 USART3_TX USART3
|
|
|
|
|
PC11 USART3_RX USART3 NODMA
|
|
|
|
|
define DEFAULT_SERIAL3_BAUD 115
|
|
|
|
|
|
|
|
|
|
# UART4 serial4
|
|
|
|
|
PA0 UART4_TX UART4
|
|
|
|
|
PA1 UART4_RX UART4 NODMA
|
|
|
|
|
|
|
|
|
|
# USART5 (DJI / VTX)
|
|
|
|
|
PC12 UART5_TX UART5
|
|
|
|
|
PD2 UART5_RX UART5 NODMA
|
|
|
|
|
|
|
|
|
|
# UART6 (onboard Telemetry)
|
|
|
|
|
PC6 USART6_TX USART6
|
|
|
|
|
PC7 USART6_RX USART6
|
|
|
|
|
define DEFAULT_SERIAL6_BAUD 115
|
|
|
|
|
|
|
|
|
|
# USB
|
|
|
|
|
PA11 OTG_FS_DM OTG1
|
|
|
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
|
|
|
|
|
|
# PWM out pins. Note that channel order follows the ArduPilot motor
|
|
|
|
|
# order conventions
|
|
|
|
|
PC9 TIM8_CH4 TIM8 PWM(1) GPIO(50)
|
|
|
|
|
PC8 TIM8_CH3 TIM8 PWM(2) GPIO(51)
|
|
|
|
|
PB1 TIM3_CH4 TIM3 PWM(3) GPIO(52)
|
|
|
|
|
PB0 TIM3_CH3 TIM3 PWM(4) GPIO(53)
|
|
|
|
|
PB6 TIM4_CH1 TIM4 PWM(5) GPIO(54)
|
|
|
|
|
PB7 TIM4_CH2 TIM4 PWM(6) GPIO(55)
|
|
|
|
|
PA8 TIM1_CH1 TIM1 PWM(7) GPIO(56)
|
|
|
|
|
PB15 TIM1_CH3N TIM1 PWM(8) GPIO(57)
|
|
|
|
|
PB14 TIM1_CH2N TIM1 PWM(9) GPIO(58)
|
|
|
|
|
PA15 TIM2_CH1 TIM2 PWM(10) GPIO(59)
|
|
|
|
|
PB11 TIM2_CH4 TIM2 PWM(11) GPIO(60)
|
|
|
|
|
PB10 TIM2_CH3 TIM2 PWM(12) GPIO(61)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
# one IMU
|
|
|
|
|
IMU Invensensev3 SPI:icm42688 ROTATION_ROLL_180_YAW_270
|
|
|
|
|
define HAL_DEFAULT_INS_FAST_SAMPLE 1
|
|
|
|
|
|
|
|
|
|
# one baro
|
|
|
|
|
BARO SPL06 I2C:0:0x77
|
|
|
|
|
define AP_BARO_BACKEND_DEFAULT_ENABLED 0
|
|
|
|
|
define AP_BARO_SPL06_ENABLED 1
|
|
|
|
|
|
|
|
|
|
# no built-in compass, but probe the i2c bus for all possible
|
|
|
|
|
# external compass types
|
|
|
|
|
define ALLOW_ARM_NO_COMPASS
|
|
|
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
|
|
|
define HAL_I2C_INTERNAL_MASK 0
|
|
|
|
|
define HAL_COMPASS_AUTO_ROT_DEFAULT 2
|
|
|
|
|
|
|
|
|
|
# ICM42688P on SPI1
|
|
|
|
|
SPIDEV icm42688 SPI1 DEVID1 MPU_CS MODE3 2*MHZ 8*MHZ
|
|
|
|
|
|
|
|
|
|
# OSD on SPI2
|
|
|
|
|
SPIDEV osd SPI2 DEVID2 OSD_CS MODE0 10*MHZ 10*MHZ
|
|
|
|
|
|
|
|
|
|
# SD Card on SPI3
|
|
|
|
|
SPIDEV sdcard SPI3 DEVID3 SDCARD_CS MODE0 400*KHZ 25*MHZ
|
|
|
|
|
|
|
|
|
|
# filesystem setup on sdcard
|
|
|
|
|
define HAL_OS_FATFS_IO 1
|
|
|
|
|
|
|
|
|
|
# setup for OSD
|
|
|
|
|
define OSD_ENABLED 1
|
|
|
|
|
define HAL_OSD_TYPE_DEFAULT 1
|
|
|
|
|
ROMFS_WILDCARD libraries/AP_OSD/fonts/font0.bin
|
|
|
|
|
|
|
|
|
|
#VTX power control
|
|
|
|
|
PC13 PINIO1 OUTPUT GPIO(81) LOW
|
|
|
|
|
|
|
|
|
|
#CAM SW
|
|
|
|
|
PB2 PINIO2 OUTPUT GPIO(82) LOW
|
|
|
|
|
|
|
|
|
|
define STM32_PWM_USE_ADVANCED TRUE
|
|
|
|
|
|
|
|
|
|
define HAL_WITH_DSP FALSE
|
|
|
|
|
|
|
|
|
|
include ../include/minimize_fpv_osd.inc
|
|
|
|
|
|
|
|
|
|
#undef AP_CAMERA_MOUNT_ENABLED
|
|
|
|
|
#undef AP_LANDINGGEAR_ENABLED
|
|
|
|
|
#undef HAL_MOUNT_ENABLED
|
|
|
|
|
#undef HAL_MOUNT_SERVO_ENABLED
|
|
|
|
|
#undef QAUTOTUNE_ENABLED
|
|
|
|
|
|
|
|
|
|
#define AP_CAMERA_MOUNT_ENABLED 1
|
|
|
|
|
#define AP_LANDINGGEAR_ENABLED 1
|
|
|
|
|
#define HAL_MOUNT_ENABLED 1
|
|
|
|
|
#define HAL_MOUNT_SERVO_ENABLED 1
|
|
|
|
|
#define QAUTOTUNE_ENABLED 1
|
|
|
|
|
|
|
|
|
|
#define DEFAULT_NTF_LED_TYPES 257
|
|
|
|
|
|
