ardupilot/libraries/AP_HAL_Linux/GPIO_BBB.cpp

130 lines
3.7 KiB
C++
Raw Normal View History

#include <AP_HAL/AP_HAL.h>
#if CONFIG_HAL_BOARD_SUBTYPE == HAL_BOARD_SUBTYPE_LINUX_PXF || \
CONFIG_HAL_BOARD_SUBTYPE == HAL_BOARD_SUBTYPE_LINUX_ERLEBOARD || \
CONFIG_HAL_BOARD_SUBTYPE == HAL_BOARD_SUBTYPE_LINUX_BBBMINI || \
CONFIG_HAL_BOARD_SUBTYPE == HAL_BOARD_SUBTYPE_LINUX_BLUE || \
CONFIG_HAL_BOARD_SUBTYPE == HAL_BOARD_SUBTYPE_LINUX_POCKET
#include "GPIO.h"
#include <stdio.h>
#include <stdlib.h>
#include <string.h>
#include <errno.h>
#include <unistd.h>
#include <fcntl.h>
#include <poll.h>
#include <sys/mman.h>
#include <sys/stat.h>
#define LOW 0
#define HIGH 1
using namespace Linux;
GPIO_BBB::GPIO_BBB()
{}
void GPIO_BBB::init()
{
#if LINUX_GPIO_NUM_BANKS == 4
int mem_fd;
/* open /dev/mem */
if ((mem_fd = open("/dev/mem", O_RDWR|O_SYNC|O_CLOEXEC)) < 0) {
printf("can't open /dev/mem \n");
exit (-1);
}
/*
Enable all GPIO clocks
Without this, access to deactivated banks (i.e. those with no clock source set up) will (logically) fail with SIGBUS
*/
volatile unsigned *cm_per = (volatile unsigned *)mmap(0, CM_PER_BASE_SIZE, PROT_READ|PROT_WRITE,
MAP_SHARED, mem_fd, CM_PER_BASE);
if ((char *)cm_per == MAP_FAILED) {
AP_HAL::panic("unable to map CM_PER registers");
}
off_t cm_offsets[LINUX_GPIO_NUM_BANKS-1] = { CM_PER_GPIO1_CLKCTRL, CM_PER_GPIO2_CLKCTRL, CM_PER_GPIO3_CLKCTRL };
for (uint8_t i=0; i<LINUX_GPIO_NUM_BANKS-1; i++) {
unsigned reg_value = *(cm_per + cm_offsets[i]);
*(cm_per + cm_offsets[i]) = (reg_value & ~0b11) | 0b10;
}
munmap((void *)cm_per, CM_PER_BASE_SIZE);
/* mmap GPIO */
off_t offsets[LINUX_GPIO_NUM_BANKS] = { GPIO0_BASE, GPIO1_BASE, GPIO2_BASE, GPIO3_BASE };
for (uint8_t i=0; i<LINUX_GPIO_NUM_BANKS; i++) {
gpio_bank[i].base = (volatile unsigned *)mmap(0, GPIO_SIZE, PROT_READ|PROT_WRITE, MAP_SHARED, mem_fd, offsets[i]);
if ((char *)gpio_bank[i].base == MAP_FAILED) {
AP_HAL::panic("unable to map GPIO bank");
}
gpio_bank[i].oe = gpio_bank[i].base + GPIO_OE;
gpio_bank[i].in = gpio_bank[i].base + GPIO_IN;
gpio_bank[i].out = gpio_bank[i].base + GPIO_OUT;
}
close(mem_fd);
#endif // LINUX_GPIO_NUM_BANKS
}
void GPIO_BBB::pinMode(uint8_t pin, uint8_t output)
{
uint8_t bank = pin/32;
uint8_t bankpin = pin & 0x1F;
if (bank >= LINUX_GPIO_NUM_BANKS) {
return;
}
if (output == HAL_GPIO_INPUT) {
*gpio_bank[bank].oe |= (1U<<bankpin);
} else {
*gpio_bank[bank].oe &= ~(1U<<bankpin);
}
}
uint8_t GPIO_BBB::read(uint8_t pin) {
uint8_t bank = pin/32;
uint8_t bankpin = pin & 0x1F;
if (bank >= LINUX_GPIO_NUM_BANKS) {
return 0;
}
return *gpio_bank[bank].in & (1U<<bankpin) ? HIGH : LOW;
}
void GPIO_BBB::write(uint8_t pin, uint8_t value)
{
uint8_t bank = pin/32;
uint8_t bankpin = pin & 0x1F;
if (bank >= LINUX_GPIO_NUM_BANKS) {
return;
}
if (value == LOW) {
*gpio_bank[bank].out &= ~(1U<<bankpin);
} else {
*gpio_bank[bank].out |= 1U<<bankpin;
}
}
void GPIO_BBB::toggle(uint8_t pin)
{
write(pin, !read(pin));
}
/* Alternative interface: */
AP_HAL::DigitalSource* GPIO_BBB::channel(uint16_t n) {
return new DigitalSource(n);
}
bool GPIO_BBB::usb_connected(void)
{
return false;
}
#endif // CONFIG_HAL_BOARD_SUBTYPE == HAL_BOARD_SUBTYPE_LINUX_PXF ||
// CONFIG_HAL_BOARD_SUBTYPE == HAL_BOARD_SUBTYPE_LINUX_ERLEBOARD ||
// CONFIG_HAL_BOARD_SUBTYPE == HAL_BOARD_SUBTYPE_LINUX_BBBMINI ||
// CONFIG_HAL_BOARD_SUBTYPE == HAL_BOARD_SUBTYPE_LINUX_BLUE ||
// CONFIG_HAL_BOARD_SUBTYPE == HAL_BOARD_SUBTYPE_LINUX_POCKET