ardupilot/libraries/AP_IMU/AP_IMU_Oilpan.cpp

370 lines
9.5 KiB
C++
Raw Normal View History

// -*- tab-width: 4; Mode: C++; c-basic-offset: 4; indent-tabs-mode: t -*-
//
//
// AP_IMU.cpp - IMU Sensor Library for Ardupilot Mega
// Code by Doug Weibel, Jordi Muñoz and Jose Julio. DIYDrones.com
//
// This library works with the ArduPilot Mega and "Oilpan"
//
// This library is free software; you can redistribute it and/or
// modify it under the terms of the GNU Lesser General Public
// License as published by the Free Software Foundation; either
// version 2.1 of the License, or (at your option) any later version.
//
/// @file AP_IMU.h
/// @brief IMU driver for the APM oilpan
#include <FastSerial.h>
#include <AP_Common.h>
#include <avr/eeprom.h>
#include "AP_IMU_Oilpan.h"
#define A_LED_PIN 37 //37 = A, 35 = C
#define C_LED_PIN 35
// ADC : Voltage reference 3.3v / 12bits(4096 steps) => 0.8mV/ADC step
// ADXL335 Sensitivity(from datasheet) => 330mV/g, 0.8mV/ADC step => 330/0.8 = 412
// Tested value : 418
#define GRAVITY 418.0 // 1G in the raw data coming from the accelerometer
#define accel_scale(x) (x*9.80665/GRAVITY) // Scaling the raw data of the accel to actual acceleration in m/s/s
// IDG500 Sensitivity (from datasheet) => 2.0mV/º/s, 0.8mV/ADC step => 0.8/3.33 = 0.4
// Tested values : 0.4026, ?, 0.4192
#define _gyro_gain_x 0.4 //X axis Gyro gain
#define _gyro_gain_y 0.41 //Y axis Gyro gain
#define _gyro_gain_z 0.41 //Z axis Gyro
#define ADC_CONSTRAINT 900
// Sensors: GYROX, GYROY, GYROZ, ACCELX, ACCELY, ACCELZ
const uint8_t AP_IMU_Oilpan::_sensors[6] = { 1, 2, 0, 4, 5, 6}; // For ArduPilot Mega Sensor Shield Hardware
const int8_t AP_IMU_Oilpan::_sensor_signs[6] = { 1,-1,-1, 1,-1,-1};
// Temp compensation curve constants
// These must be produced by measuring data and curve fitting
// [X/Y/Z gyro][A/B/C or 0 order/1st order/2nd order constants]
const float AP_IMU_Oilpan::_gyro_temp_curve[3][3] = {
{1665,0,0},
{1665,0,0},
{1665,0,0}
}; // To Do - make additional constructors to pass this in.
void
AP_IMU_Oilpan::init(Start_style style)
{
init_gyro(style);
init_accel(style);
}
/**************************************************/
void
AP_IMU_Oilpan::init_gyro(Start_style style)
{
float temp;
int flashcount = 0;
int tc_temp;
float adc_in[6];
// warm start, load saved cal from EEPROM
if ((WARM_START == style) && (0 != _address)) {
_adc_offset[0] = read_EE_float(_address );
_adc_offset[1] = read_EE_float(_address + 4);
_adc_offset[2] = read_EE_float(_address + 8);
return;
}
// cold start
tc_temp = _adc->Ch(_gyro_temp_ch);
delay(500);
Serial.println("Init Gyro");
for(int c = 0; c < 25; c++){ // Mostly we are just flashing the LED's here to tell the user to keep the IMU still
digitalWrite(A_LED_PIN, LOW);
digitalWrite(C_LED_PIN, HIGH);
delay(20);
for (int i = 0; i < 6; i++)
adc_in[i] = _adc->Ch(_sensors[i]);
digitalWrite(A_LED_PIN, HIGH);
digitalWrite(C_LED_PIN, LOW);
delay(20);
}
for (int j = 0; j <= 2; j++){
adc_in[j] -= _gyro_temp_comp(j, tc_temp);
_adc_offset[j] = adc_in[j];
}
for(int i = 0; i < 50; i++){
for (int j = 0; j <= 2; j++){
adc_in[j] = _adc->Ch(_sensors[j]);
// Subtract temp compensated typical gyro bias
adc_in[j] -= _gyro_temp_comp(j, tc_temp);
// filter
_adc_offset[j] = _adc_offset[j] * 0.9 + adc_in[j] * 0.1;
}
delay(20);
if(flashcount == 5) {
Serial.print("*");
digitalWrite(A_LED_PIN, LOW);
digitalWrite(C_LED_PIN, HIGH);
}
if(flashcount >= 10) {
flashcount = 0;
digitalWrite(C_LED_PIN, LOW);
digitalWrite(A_LED_PIN, HIGH);
}
flashcount++;
}
_save_gyro_cal();
}
void
AP_IMU_Oilpan::init_accel(Start_style style) // 3, 4, 5
{
float temp;
int flashcount = 0;
float adc_in[6];
// warm start, load our saved cal from EEPROM
if ((WARM_START == style) && (0 != _address)) {
_adc_offset[3] = read_EE_float(_address + 12);
_adc_offset[4] = read_EE_float(_address + 16);
_adc_offset[5] = read_EE_float(_address + 20);
return;
}
// cold start
delay(500);
Serial.println("Init Accel");
for (int j = 3; j <= 5; j++){
adc_in[j] = _adc->Ch(_sensors[j]);
adc_in[j] -= 2025; // Typical accel bias value - subtracted in _accel_in() and update()
_adc_offset[j] = adc_in[j];
}
for(int i = 0; i < 50; i++){ // We take some readings...
delay(20);
for (int j = 3; j <= 5; j++){
adc_in[j] = _adc->Ch(_sensors[j]);
adc_in[j] -= 2025; // Typical accel bias value - subtracted in _accel_in() and update()
_adc_offset[j] = _adc_offset[j] * 0.9 + adc_in[j] * 0.1;
}
if(flashcount == 5) {
Serial.print("*");
digitalWrite(A_LED_PIN, LOW);
digitalWrite(C_LED_PIN, HIGH);
}
if(flashcount >= 10) {
flashcount = 0;
digitalWrite(C_LED_PIN, LOW);
digitalWrite(A_LED_PIN, HIGH);
}
flashcount++;
}
Serial.println(" ");
_adc_offset[5] += GRAVITY * _sensor_signs[5];
_save_accel_cal();
}
void
AP_IMU_Oilpan::zero_accel(void) // 3, 4, 5
{
_adc_offset[3] = 0;
_adc_offset[4] = 0;
_adc_offset[5] = 0;
_save_accel_cal();
}
void
AP_IMU_Oilpan::_save_gyro_cal(void)
{
// save cal to EEPROM for warm start
if (0 != _address) {
write_EE_float(_adc_offset[0], _address);
write_EE_float(_adc_offset[1], _address + 4);
write_EE_float(_adc_offset[2], _address + 8);
}
}
void
AP_IMU_Oilpan::_save_accel_cal(void)
{
// save cal to EEPROM for warm start
if (0 != _address) {
write_EE_float(_adc_offset[3], _address + 12);
write_EE_float(_adc_offset[4], _address + 16);
write_EE_float(_adc_offset[5], _address + 20);
}
}
/**************************************************/
// Returns the temperature compensated raw gyro value
//---------------------------------------------------
float
AP_IMU_Oilpan::_gyro_temp_comp(int i, int temp) const
{
// We use a 2nd order curve of the form Gtc = A + B * Graw + C * (Graw)**2
//------------------------------------------------------------------------
return _gyro_temp_curve[i][0] + _gyro_temp_curve[i][1] * temp + _gyro_temp_curve[i][2] * temp * temp;
}
float
AP_IMU_Oilpan::_gyro_in(uint8_t channel, int temperature)
{
float adc_in;
adc_in = _adc->Ch(_sensors[channel]);
adc_in -= _gyro_temp_comp(channel, temperature); // Subtract temp compensated typical gyro bias
if (_sensor_signs[channel] < 0) {
adc_in = _adc_offset[channel] - adc_in;
} else {
adc_in = adc_in - _adc_offset[channel];
}
if (fabs(adc_in) > ADC_CONSTRAINT) {
adc_constraints++; // We keep track of the number of times
adc_in = constrain(adc_in, -ADC_CONSTRAINT, ADC_CONSTRAINT); // Throw out nonsensical values
}
return adc_in;
}
float
AP_IMU_Oilpan::_accel_in(uint8_t channel)
{
float adc_in;
adc_in = _adc->Ch(_sensors[channel]);
adc_in -= 2025; // Subtract typical accel bias
if (_sensor_signs[channel] < 0) {
adc_in = _adc_offset[channel] - adc_in;
} else {
adc_in = adc_in - _adc_offset[channel];
}
if (fabs(adc_in) > ADC_CONSTRAINT) {
adc_constraints++; // We keep track of the number of times
adc_in = constrain(adc_in, -ADC_CONSTRAINT, ADC_CONSTRAINT); // Throw out nonsensical values
}
return adc_in;
}
bool
AP_IMU_Oilpan::update(void)
{
int tc_temp = _adc->Ch(_gyro_temp_ch);
float adc_in[6];
#if 0
// get current gyro readings
for (int i = 0; i < 3; i++) {
adc_in[i] = _adc->Ch(_sensors[i]);
adc_in[i] -= _gyro_temp_comp(i,tc_temp); // Subtract temp compensated typical gyro bias
if (_sensor_signs[i] < 0)
adc_in[i] = (_adc_offset[i] - adc_in[i]);
else
adc_in[i] = (adc_in[i] - _adc_offset[i]);
if (fabs(adc_in[i]) > ADC_CONSTRAINT) {
adc_constraints++; // We keep track of the number of times
adc_in[i] = constrain(adc_in[i], -ADC_CONSTRAINT, ADC_CONSTRAINT); // Throw out nonsensical values
}
}
#endif
_gyro.x = ToRad(_gyro_gain_x) * _gyro_in(0, tc_temp);
_gyro.y = ToRad(_gyro_gain_y) * _gyro_in(1, tc_temp);
_gyro.z = ToRad(_gyro_gain_z) * _gyro_in(2, tc_temp);
#if 0
// get current accelerometer readings
for (int i = 3; i < 6; i++) {
adc_in[i] = _adc->Ch(_sensors[i]);
adc_in[i] -= 2025; // Subtract typical accel bias
if (_sensor_signs[i] < 0)
adc_in[i] = _adc_offset[i] - adc_in[i];
else
adc_in[i] = adc_in[i] - _adc_offset[i];
if (fabs(adc_in[i]) > ADC_CONSTRAINT) {
adc_constraints++; // We keep track of the number of times
adc_in[i] = constrain(adc_in[i], -ADC_CONSTRAINT, ADC_CONSTRAINT); // Throw out nonsensical values
}
}
#endif
_accel.x = accel_scale(_accel_in(3));
_accel.y = accel_scale(_accel_in(4));
_accel.z = accel_scale(_accel_in(5));
// always updated
return true;
}
/********************************************************************************/
void
AP_IMU_Oilpan::print_accel_offsets(void)
{
Serial.print("Accel offsets: ");
Serial.print(_adc_offset[3], 2);
Serial.print(", ");
Serial.print(_adc_offset[4], 2);
Serial.print(", ");
Serial.println(_adc_offset[5], 2);
}
void
AP_IMU_Oilpan::print_gyro_offsets(void)
{
Serial.print("Gyro offsets: ");
Serial.print(_adc_offset[0], 2);
Serial.print(", ");
Serial.print(_adc_offset[1], 2);
Serial.print(", ");
Serial.println(_adc_offset[2], 2);
}
/********************************************************************************/
float
AP_IMU_Oilpan::read_EE_float(int address)
{
union {
byte bytes[4];
float value;
} _floatOut;
for (int i = 0; i < 4; i++)
_floatOut.bytes[i] = eeprom_read_byte((uint8_t *) (address + i));
return _floatOut.value;
}
void
AP_IMU_Oilpan::write_EE_float(float value, int address)
{
union {
byte bytes[4];
float value;
} _floatIn;
_floatIn.value = value;
for (int i = 0; i < 4; i++)
eeprom_write_byte((uint8_t *) (address + i), _floatIn.bytes[i]);
}