2019-10-08 16:48:05 -03:00
|
|
|
# hw definition file for processing by chibios_pins.py
|
|
|
|
|
# for Holybro KakuteF7 Mini hardware.
|
|
|
|
|
@ thanks to betaflight for pin information
|
|
|
|
|
|
|
|
|
|
# MCU class and specific type
|
|
|
|
|
MCU STM32F7xx STM32F745xx
|
|
|
|
|
|
|
|
|
|
# board ID for firmware load
|
|
|
|
|
APJ_BOARD_ID 145
|
|
|
|
|
|
|
|
|
|
# crystal frequency, setup to use external oscillator
|
|
|
|
|
OSCILLATOR_HZ 8000000
|
|
|
|
|
|
|
|
|
|
FLASH_SIZE_KB 1024
|
|
|
|
|
|
|
|
|
|
# leave 2 sectors free
|
|
|
|
|
FLASH_RESERVE_START_KB 96
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
# only one I2C bus
|
|
|
|
|
I2C_ORDER I2C1
|
|
|
|
|
|
|
|
|
|
# order of UARTs (and USB), USART3 should be in second place to map order with the board's silk screen
|
2020-04-24 08:10:08 -03:00
|
|
|
SERIAL_ORDER OTG1 USART1 USART2 USART3 UART4 EMPTY USART6 UART7
|
2019-10-08 16:48:05 -03:00
|
|
|
|
|
|
|
|
# buzzer
|
|
|
|
|
PD15 TIM4_CH4 TIM4 GPIO(77) ALARM
|
|
|
|
|
#PD15 BUZZER OUTPUT GPIO(80) LOW
|
|
|
|
|
#define HAL_BUZZER_PIN 80
|
|
|
|
|
#define HAL_BUZZER_ON 1
|
|
|
|
|
#define HAL_BUZZER_OFF 0
|
|
|
|
|
|
|
|
|
|
# PA10 IO-debug-console
|
|
|
|
|
PA11 OTG_FS_DM OTG1
|
|
|
|
|
PA12 OTG_FS_DP OTG1
|
|
|
|
|
|
|
|
|
|
PA13 JTMS-SWDIO SWD
|
|
|
|
|
PA14 JTCK-SWCLK SWD
|
|
|
|
|
|
|
|
|
|
# SPI1 for M25P16 dataflash
|
|
|
|
|
PA4 FLASH_CS CS
|
|
|
|
|
PA5 SPI1_SCK SPI1
|
|
|
|
|
PA6 SPI1_MISO SPI1
|
|
|
|
|
PA7 SPI1_MOSI SPI1
|
|
|
|
|
|
|
|
|
|
# SPI2 for MAX7456 OSD
|
|
|
|
|
PB12 MAX7456_CS CS
|
|
|
|
|
PB13 SPI2_SCK SPI2
|
|
|
|
|
PB14 SPI2_MISO SPI2
|
|
|
|
|
PB15 SPI2_MOSI SPI2
|
|
|
|
|
|
|
|
|
|
# SPI4 for ICM20689
|
|
|
|
|
PE4 ICM20689_CS CS
|
|
|
|
|
PE2 SPI4_SCK SPI4
|
|
|
|
|
PE5 SPI4_MISO SPI4
|
|
|
|
|
PE6 SPI4_MOSI SPI4
|
|
|
|
|
|
|
|
|
|
# I2C1 for baro
|
|
|
|
|
PB6 I2C1_SCL I2C1
|
|
|
|
|
PB7 I2C1_SDA I2C1
|
|
|
|
|
|
|
|
|
|
PC3 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
|
|
|
|
PC2 BATT_CURRENT_SENS ADC1 SCALE(1)
|
|
|
|
|
|
|
|
|
|
# define default battery setup
|
|
|
|
|
define HAL_BATT_VOLT_PIN 13
|
|
|
|
|
define HAL_BATT_CURR_PIN 12
|
|
|
|
|
define HAL_BATT_VOLT_SCALE 10.9
|
|
|
|
|
define HAL_BATT_CURR_SCALE 28.5
|
|
|
|
|
|
|
|
|
|
PC5 RSSI_ADC ADC1
|
|
|
|
|
|
|
|
|
|
PA2 LED0 OUTPUT LOW
|
|
|
|
|
|
|
|
|
|
# USART1
|
|
|
|
|
PA10 USART1_RX USART1
|
|
|
|
|
PA9 USART1_TX USART1
|
|
|
|
|
|
|
|
|
|
# USART2
|
|
|
|
|
PD5 USART2_TX USART2
|
|
|
|
|
PD6 USART2_RX USART2
|
|
|
|
|
|
|
|
|
|
# USART3 (GPS)
|
|
|
|
|
PB11 USART3_RX USART3
|
|
|
|
|
PB10 USART3_TX USART3
|
|
|
|
|
|
|
|
|
|
# UART4 (GPS2)
|
|
|
|
|
PA0 UART4_TX UART4 NODMA
|
|
|
|
|
PA1 UART4_RX UART4 NODMA
|
|
|
|
|
|
2020-01-02 19:34:39 -04:00
|
|
|
# RC input defaults to timer capture
|
|
|
|
|
PC7 TIM8_CH2 TIM8 RCININT PULLDOWN
|
|
|
|
|
PC6 USART6_TX USART6 NODMA
|
|
|
|
|
|
|
|
|
|
# alt config to allow RCIN on UART for bi-directional
|
|
|
|
|
# protocols like FPort
|
|
|
|
|
PC7 USART6_RX USART6 NODMA ALT(1)
|
2019-10-08 16:48:05 -03:00
|
|
|
|
|
|
|
|
# UART7, RX only for ESC Telemetry
|
|
|
|
|
PE7 UART7_RX UART7
|
|
|
|
|
PE8 UART7_TX UART7 NODMA LOW
|
|
|
|
|
|
|
|
|
|
# Motors
|
|
|
|
|
PB1 TIM1_CH3N TIM1 PWM(1) GPIO(50)
|
|
|
|
|
PE9 TIM1_CH1 TIM1 PWM(2) GPIO(51)
|
|
|
|
|
PE11 TIM1_CH2 TIM1 PWM(3) GPIO(52)
|
|
|
|
|
PB0 TIM3_CH3 TIM3 PWM(4) GPIO(53)
|
|
|
|
|
PC9 TIM3_CH4 TIM3 PWM(5) GPIO(54)
|
|
|
|
|
PA3 TIM5_CH4 TIM5 PWM(6) GPIO(55)
|
|
|
|
|
|
|
|
|
|
# extra PWM outs
|
|
|
|
|
#PD12 TIM4_CH1 TIM4 PWM(7) GPIO(56) # led pin
|
|
|
|
|
#PD15 TIM4_CH4 TIM4 PWM(8) GPIO(57) # buzzer pin (need to comment out buzzer)
|
|
|
|
|
|
|
|
|
|
DMA_PRIORITY S*
|
|
|
|
|
|
|
|
|
|
define HAL_STORAGE_SIZE 16384
|
|
|
|
|
define STORAGE_FLASH_PAGE 1
|
|
|
|
|
|
|
|
|
|
# enable logging to dataflash
|
|
|
|
|
define HAL_LOGGING_DATAFLASH
|
|
|
|
|
|
|
|
|
|
# spi devices
|
|
|
|
|
SPIDEV mpu6000 SPI4 DEVID1 ICM20689_CS MODE3 1*MHZ 4*MHZ
|
|
|
|
|
SPIDEV dataflash SPI1 DEVID1 FLASH_CS MODE3 32*MHZ 32*MHZ
|
|
|
|
|
SPIDEV osd SPI2 DEVID4 MAX7456_CS MODE0 10*MHZ 10*MHZ
|
|
|
|
|
|
|
|
|
|
# no built-in compass, but probe the i2c bus for all possible
|
|
|
|
|
# external compass types
|
|
|
|
|
define ALLOW_ARM_NO_COMPASS
|
|
|
|
|
define HAL_COMPASS_DEFAULT HAL_COMPASS_NONE
|
|
|
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
|
|
|
|
define HAL_I2C_INTERNAL_MASK 0
|
|
|
|
|
define HAL_COMPASS_AUTO_ROT_DEFAULT 2
|
|
|
|
|
|
|
|
|
|
# one IMU
|
|
|
|
|
IMU Invensense SPI:mpu6000 ROTATION_YAW_180
|
|
|
|
|
|
|
|
|
|
# one BARO
|
|
|
|
|
BARO BMP280 I2C:0:0x76
|
|
|
|
|
|
|
|
|
|
# setup for OSD
|
2019-12-20 13:46:24 -04:00
|
|
|
define OSD_ENABLED 1
|
2019-10-08 16:48:05 -03:00
|
|
|
define HAL_OSD_TYPE_DEFAULT 1
|
|
|
|
|
ROMFS_WILDCARD libraries/AP_OSD/fonts/font*.bin
|
|
|
|
|
|
|
|
|
|
define BOARD_PWM_COUNT_DEFAULT 6
|
|
|
|
|
define STM32_PWM_USE_ADVANCED TRUE
|
|
|
|
|
|
2020-01-18 04:38:19 -04:00
|
|
|
# disable SMBUS and fuel battery monitors to save flash
|
|
|
|
|
define HAL_BATTMON_SMBUS_ENABLE 0
|
|
|
|
|
define HAL_BATTMON_FUEL_ENABLE 0
|
|
|
|
|
|
|
|
|
|
# disable parachute and sprayer to save flash
|
|
|
|
|
define HAL_PARACHUTE_ENABLED 0
|
|
|
|
|
define HAL_SPRAYER_ENABLED 0
|
2020-01-30 19:53:03 -04:00
|
|
|
|
|
|
|
|
# reduce max size of embedded params for apj_tool.py
|
|
|
|
|
define AP_PARAM_MAX_EMBEDDED_PARAM 1024
|
2020-07-24 14:47:16 -03:00
|
|
|
|
|
|
|
|
define HAL_MOUNT_ENABLED 0
|
