ardupilot/ArduSub/control_althold.cpp

103 lines
4.5 KiB
C++
Raw Normal View History

2016-01-14 15:30:56 -04:00
#include "Sub.h"
/*
* control_althold.pde - init and run calls for althold, flight mode
*/
// althold_init - initialise althold controller
bool Sub::althold_init()
{
#if CONFIG_HAL_BOARD != HAL_BOARD_SITL
if (!ap.depth_sensor_present || failsafe.sensor_health) { // can't hold depth without a depth sensor, exit immediately.
gcs().send_text(MAV_SEVERITY_WARNING, "BAD DEPTH");
return false;
}
#endif
// initialize vertical speeds and leash lengths
// sets the maximum speed up and down returned by position controller
pos_control.set_speed_z(-g.pilot_velocity_z_max, g.pilot_velocity_z_max);
pos_control.set_accel_z(g.pilot_accel_z);
// initialise position and desired velocity
pos_control.set_alt_target(inertial_nav.get_altitude());
pos_control.set_desired_velocity_z(inertial_nav.get_velocity_z());
last_pilot_heading = ahrs.yaw_sensor;
return true;
}
// althold_run - runs the althold controller
// should be called at 100hz or more
2016-01-14 15:30:56 -04:00
void Sub::althold_run()
{
uint32_t tnow = AP_HAL::millis();
// initialize vertical speeds and acceleration
pos_control.set_speed_z(-g.pilot_velocity_z_max, g.pilot_velocity_z_max);
pos_control.set_accel_z(g.pilot_accel_z);
if (!motors.armed()) {
motors.set_desired_spool_state(AP_Motors::DESIRED_SPIN_WHEN_ARMED);
2017-02-10 13:46:54 -04:00
// Sub vehicles do not stabilize roll/pitch/yaw when not auto-armed (i.e. on the ground, pilot has never raised throttle)
attitude_control.set_throttle_out_unstabilized(0,true,g.throttle_filt);
pos_control.relax_alt_hold_controllers(motors.get_throttle_hover());
last_pilot_heading = ahrs.yaw_sensor;
return;
}
motors.set_desired_spool_state(AP_Motors::DESIRED_THROTTLE_UNLIMITED);
// get pilot desired lean angles
float target_roll, target_pitch;
get_pilot_desired_lean_angles(channel_roll->get_control_in(), channel_pitch->get_control_in(), target_roll, target_pitch, attitude_control.get_althold_lean_angle_max());
// get pilot's desired yaw rate
float target_yaw_rate = get_pilot_desired_yaw_rate(channel_yaw->get_control_in());
// call attitude controller
if (!is_zero(target_yaw_rate)) { // call attitude controller with rate yaw determined by pilot input
attitude_control.input_euler_angle_roll_pitch_euler_rate_yaw(target_roll, target_pitch, target_yaw_rate, get_smoothing_gain());
last_pilot_heading = ahrs.yaw_sensor;
last_pilot_yaw_input_ms = tnow; // time when pilot last changed heading
} else { // hold current heading
// this check is required to prevent bounce back after very fast yaw maneuvers
// the inertia of the vehicle causes the heading to move slightly past the point when pilot input actually stopped
if (tnow < last_pilot_yaw_input_ms + 250) { // give 250ms to slow down, then set target heading
target_yaw_rate = 0; // Stop rotation on yaw axis
// call attitude controller with target yaw rate = 0 to decelerate on yaw axis
attitude_control.input_euler_angle_roll_pitch_euler_rate_yaw(target_roll, target_pitch, target_yaw_rate, get_smoothing_gain());
last_pilot_heading = ahrs.yaw_sensor; // update heading to hold
} else { // call attitude controller holding absolute absolute bearing
attitude_control.input_euler_angle_roll_pitch_yaw(target_roll, target_pitch, last_pilot_heading, true, get_smoothing_gain());
}
}
2017-02-27 14:06:55 -04:00
if (fabsf(channel_throttle->norm_input()-0.5) > 0.05) { // Throttle input above 5%
// output pilot's throttle
attitude_control.set_throttle_out(channel_throttle->norm_input(), false, g.throttle_filt);
// reset z targets to current values
pos_control.relax_alt_hold_controllers(motors.get_throttle_hover());
} else { // hold z
if (ap.at_bottom) {
pos_control.relax_alt_hold_controllers(motors.get_throttle_hover()); // clear velocity and position targets, and integrator
pos_control.set_alt_target(inertial_nav.get_altitude() + 10.0f); // set target to 10 cm above bottom
} else if (rangefinder_alt_ok()) {
// if rangefinder is ok, use surface tracking
float target_climb_rate = get_surface_tracking_climb_rate(0, pos_control.get_alt_target(), G_Dt);
pos_control.set_alt_target_from_climb_rate_ff(target_climb_rate, G_Dt, false);
}
pos_control.update_z_controller();
}
motors.set_forward(channel_forward->norm_input());
motors.set_lateral(channel_lateral->norm_input());
}