ardupilot/libraries/AP_HAL_ChibiOS/hwdef/KakuteF4/hwdef.dat

147 lines
2.9 KiB
Plaintext
Raw Normal View History

# hw definition file for KakuteF4 hardware
# STATUS:
# This port is mostly complete. Main missing feature are OSD,
2018-06-16 08:09:31 -03:00
# dataflash
# MCU class and specific type
MCU STM32F4xx STM32F405xx
# board ID for firmware load
2018-06-16 08:09:31 -03:00
APJ_BOARD_ID 122
# crystal frequency
OSCILLATOR_HZ 8000000
STM32_PLLM_VALUE 8
define STM32_ST_USE_TIMER 4
define CH_CFG_ST_RESOLUTION 16
FLASH_SIZE_KB 1024
# board voltage
STM32_VDD 330U
# only one I2C bus
I2C_ORDER I2C1
# order of UARTs (and USB)
UART_ORDER OTG1 USART1 UART4 UART5
# LEDs
PB5 LED_BLUE OUTPUT LOW GPIO(0)
# buzzer
PC9 BUZZER OUTPUT GPIO(80) LOW
define HAL_BUZZER_PIN 80
define HAL_BUZZER_ON 1
define HAL_BUZZER_OFF 0
# spi1 bus for IMU
PA5 SPI1_SCK SPI1
PA6 SPI1_MISO SPI1
PA7 SPI1_MOSI SPI1
# spi3 for dataflash and OSD
PC10 SPI3_SCK SPI3
PC11 SPI3_MISO SPI3
PC12 SPI3_MOSI SPI3
PB14 MAX7456_CS CS
# dataflash M25P16
PB3 M25P16_CS CS
PC4 ICM20689_CS CS
PC5 ICM20689_DRDY INPUT
# only one I2C bus in normal config
PB8 I2C1_SCL I2C1
PB9 I2C1_SDA I2C1
# rcinput is PB11
PB11 TIM2_CH4 TIM2 RCININT FLOAT LOW
# analog pins
PC3 BATT_VOLTAGE_SENS ADC1 SCALE(1)
PC2 BATT_CURRENT_SENS ADC1 SCALE(1)
# define default battery setup
define HAL_BATT_VOLT_PIN 13
define HAL_BATT_CURR_PIN 12
define HAL_BATT_VOLT_SCALE 10.1
define HAL_BATT_CURR_SCALE 17.0
# main port, for telem1
PA9 USART1_TX USART1
PA10 USART1_RX USART1
# USART3 for rcinput
#PB10 USART3_TX USART3
#PB11 USART3_RX USART3
PB15 SBUS_INVERT OUTPUT LOW
# USART6
#PC6 USART6_TX USART6
#PC7 USART6_RX USART6
# UART4 (GPS)
PA1 UART4_RX UART4
PA0 UART4_TX UART4
# UART5 (ESC sensor)
PD2 UART5_RX UART5
# PA10 IO-debug-console
PA11 OTG_FS_DM OTG1
PA12 OTG_FS_DP OTG1
# USB detection
PA8 VBUS INPUT OPENDRAIN
# debug
PA13 JTMS-SWDIO SWD
PA14 JTCK-SWCLK SWD
# PWM out pins. Note that channel order follows the ArduPilot motor
# order conventions
PB1 TIM3_CH4 TIM3 PWM(1) GPIO(50)
PA3 TIM5_CH4 TIM5 PWM(2) GPIO(51)
PA2 TIM5_CH3 TIM5 PWM(3) GPIO(52)
PB0 TIM3_CH3 TIM3 PWM(4) GPIO(53)
# PC8 TIM8_CH3 TIM2 GPIO(54) # LED strip
define HAL_STORAGE_SIZE 15360
2018-06-16 08:09:31 -03:00
define STORAGE_FLASH_PAGE 2
2018-06-16 08:09:31 -03:00
# reserve 32k for bootloader and 32k for flash storage
FLASH_RESERVE_START_KB 64
define HAL_INS_DEFAULT HAL_INS_MPU60XX_SPI
define HAL_INS_DEFAULT_ROTATION ROTATION_YAW_180
# there is no compass fitted by default
define ALLOW_ARM_NO_COMPASS
define HAL_COMPASS_DEFAULT HAL_COMPASS_HMC5843
define HAL_COMPASS_HMC5843_I2C_BUS 0
define HAL_COMPASS_HMC5843_I2C_ADDR 0x1E
define HAL_COMPASS_HMC5843_ROTATION ROTATION_YAW_90
define HAL_BARO_DEFAULT HAL_BARO_BMP280_I2C
define HAL_BARO_BMP280_BUS 0
define HAL_BARO_BMP280_I2C_ADDR 0x76
# SPI devices
SPIDEV mpu6000 SPI1 DEVID1 ICM20689_CS MODE3 1*MHZ 8*MHZ
SPIDEV dataflash SPI3 DEVID1 M25P16_CS MODE3 1*MHZ 8*MHZ
2018-06-24 07:00:07 -03:00
SPIDEV osd SPI3 DEVID4 MAX7456_CS MODE0 10*MHZ 10*MHZ
# setup for OSD
define OSD_ENABLED ENABLED
ROMFS osd_font.bin libraries/AP_OSD/fonts/clarity.bin
# 8 PWM available by default
define BOARD_PWM_COUNT_DEFAULT 8