mirror of https://github.com/ArduPilot/ardupilot
103 lines
3.1 KiB
Markdown
103 lines
3.1 KiB
Markdown
|
# SpeedyBee F405 Mini Flight Controller
|
||
|
|
|
||
|
|
The SpeedyBee F405 Mini is a flight controller produced by [SpeedyBee](http://www.speedybee.com/).
|
||
|
|
|
||
|
|
## Features
|
||
|
|
|
||
|
|
- STM32F405 microcontroller
|
||
|
|
- ICM42688-P IMU
|
||
|
|
- DPS310 barometer
|
||
|
|
- 8Mb flash logging
|
||
|
|
- AT7456E OSD
|
||
|
|
- 6 UARTs
|
||
|
|
- 5 PWM outputs
|
||
|
|
|
||
|
|
## Pinout
|
||
|
|
|
||
|
|
|
||
|
|
|
||
|
|
## UART Mapping
|
||
|
|
|
||
|
|
The UARTs are marked Rn and Tn in the above pinouts. The Rn pin is the
|
||
|
|
receive pin for UARTn. The Tn pin is the transmit pin for UARTn.
|
||
|
|
|
||
|
|
- SERIAL0 -> USB
|
||
|
|
- SERIAL1 -> UART1 (DJI-VTX, DMA-enabled)
|
||
|
|
- SERIAL2 -> UART2 (RX, DMA-enabled)
|
||
|
|
- SERIAL3 -> UART3
|
||
|
|
- SERIAL4 -> UART4 (connected to internal BT module, not currently usable by ArduPilot)
|
||
|
|
- SERIAL5 -> UART5 (ESC Telemetry, RX only on ESC connector)
|
||
|
|
- SERIAL6 -> UART6 (GPS, DMA-enabled)
|
||
|
|
|
||
|
|
## RC Input
|
||
|
|
|
||
|
|
RC input is configured on the R2 (UART2_RX) pin for most RC unidirectional protocols except SBUS which should be applied at the SBUS pin. PPM is not supported.
|
||
|
|
For Fport, a bi-directional inverter will be required. See https://ardupilot.org/plane/docs/common-connecting-sport-fport.html
|
||
|
|
For CRSF/ELRS/SRXL2 connection of the receiver to T2 will also be required.
|
||
|
|
|
||
|
|
## FrSky Telemetry
|
||
|
|
|
||
|
|
FrSky Telemetry is supported using the Tx pin of any UART including SERIAL2/UART2. You need to set the following parameters to enable support for FrSky S.PORT (example shows SERIAL3).
|
||
|
|
|
||
|
|
- SERIAL3_PROTOCOL 10
|
||
|
|
- SERIAL3_OPTIONS 7
|
||
|
|
|
||
|
|
## OSD Support
|
||
|
|
|
||
|
|
The SpeedyBee F405 Mini supports OSD using OSD_TYPE 1 (MAX7456 driver).
|
||
|
|
|
||
|
|
## VTX Support
|
||
|
|
|
||
|
|
The JST-GH-6P connector supports a standard DJI HD VTX connection. Pin 1 of the connector is 9v so be careful not to connect
|
||
|
|
this to a peripheral requiring 5v.
|
||
|
|
|
||
|
|
## PWM Output
|
||
|
|
|
||
|
|
The SpeedyBee F405 Mini supports up to 5 PWM outputs. The pads for motor output
|
||
|
|
M1 to M4 on the motor connector, plus M5 for LED strip or another
|
||
|
|
PWM output.
|
||
|
|
|
||
|
|
The PWM is in 3 groups:
|
||
|
|
|
||
|
|
- PWM 1-2 in group1
|
||
|
|
- PWM 3-4 in group2
|
||
|
|
- PWM 5 in group3
|
||
|
|
|
||
|
|
Channels within the same group need to use the same output rate. If
|
||
|
|
any channel in a group uses DShot then all channels in the group need
|
||
|
|
to use DShot. Channels 1-4 support bi-directional DShot.
|
||
|
|
|
||
|
|
## Battery Monitoring
|
||
|
|
|
||
|
|
The board has a internal voltage sensor and connections on the ESC connector for an external current sensor input.
|
||
|
|
The voltage sensor can handle up to 6S.
|
||
|
|
LiPo batteries.
|
||
|
|
|
||
|
|
The default battery parameters are:
|
||
|
|
|
||
|
|
- BATT_MONITOR 4
|
||
|
|
- BATT_VOLT_PIN 10
|
||
|
|
- BATT_CURR_PIN 11
|
||
|
|
- BATT_VOLT_MULT 11.2
|
||
|
|
- BATT_AMP_PERVLT 40 (will need to be adjusted for whichever current sensor is attached)
|
||
|
|
|
||
|
|
|
||
|
|
## RSSI
|
||
|
|
|
||
|
|
Analog RSSI input (pin 15)
|
||
|
|
|
||
|
|
## Compass
|
||
|
|
|
||
|
|
The SpeedyBee F405 Mini does not have a builtin compass, but you can attach an external compass using I2C on the SDA and SCL pads.
|
||
|
|
|
||
|
|
## Loading Firmware
|
||
|
|
|
||
|
|
Initial firmware load can be done with DFU by plugging in USB with the
|
||
|
|
bootloader button pressed. Then you should load the "with_bl.hex"
|
||
|
|
firmware, using your favourite DFU loading tool.
|
||
|
|
|
||
|
|
Once the initial firmware is loaded you can update the firmware using
|
||
|
|
any ArduPilot ground station software. Updates should be done with the
|
||
|
|
*.apj firmware files.
|
||
|
|
|