mirror of https://github.com/ArduPilot/ardupilot
106 lines
2.1 KiB
Plaintext
106 lines
2.1 KiB
Plaintext
|
# Hitec Mosaic GPS
|
||
|
|
|
||
|
|
# MCU class and specific type
|
||
|
|
MCU STM32F303 STM32F303xC
|
||
|
|
|
||
|
|
FLASH_RESERVE_START_KB 0
|
||
|
|
FLASH_BOOTLOADER_LOAD_KB 26
|
||
|
|
|
||
|
|
# board ID for firmware load
|
||
|
|
APJ_BOARD_ID 1016
|
||
|
|
|
||
|
|
# setup build for a peripheral firmware
|
||
|
|
env AP_PERIPH 1
|
||
|
|
|
||
|
|
# crystal frequency
|
||
|
|
OSCILLATOR_HZ 24000000
|
||
|
|
|
||
|
|
define CH_CFG_ST_FREQUENCY 1000
|
||
|
|
|
||
|
|
# assume 256k flash part
|
||
|
|
FLASH_SIZE_KB 256
|
||
|
|
|
||
|
|
# order of UARTs
|
||
|
|
SERIAL_ORDER
|
||
|
|
define HAL_USE_UART FALSE
|
||
|
|
|
||
|
|
PA6 LED_BOOTLOADER OUTPUT LOW
|
||
|
|
define HAL_LED_ON 1
|
||
|
|
|
||
|
|
STDOUT_SERIAL SD2
|
||
|
|
STDOUT_BAUDRATE 57600
|
||
|
|
|
||
|
|
# USART2, debug
|
||
|
|
PA2 USART2_TX USART2 SPEED_HIGH NODMA
|
||
|
|
PA3 USART2_RX USART2 SPEED_HIGH NODMA
|
||
|
|
|
||
|
|
# USART3, GPS
|
||
|
|
PB10 USART3_TX USART3 SPEED_HIGH NODMA
|
||
|
|
PB11 USART3_RX USART3 SPEED_HIGH NODMA
|
||
|
|
|
||
|
|
define HAL_USE_SERIAL TRUE
|
||
|
|
|
||
|
|
define STM32_SERIAL_USE_USART1 FALSE
|
||
|
|
define STM32_SERIAL_USE_USART2 TRUE
|
||
|
|
define STM32_SERIAL_USE_USART3 TRUE
|
||
|
|
|
||
|
|
PA13 SWDIO-JTMS SWD
|
||
|
|
PA14 SWCLK-JTCK SWD
|
||
|
|
|
||
|
|
define HAL_NO_GPIO_IRQ
|
||
|
|
define CH_CFG_ST_TIMEDELTA 0
|
||
|
|
#define CH_CFG_USE_DYNAMIC FALSE
|
||
|
|
define SERIAL_BUFFERS_SIZE 32
|
||
|
|
define HAL_USE_EMPTY_IO TRUE
|
||
|
|
define PORT_INT_REQUIRED_STACK 64
|
||
|
|
|
||
|
|
# avoid timer and RCIN threads to save memory
|
||
|
|
define HAL_NO_TIMER_THREAD
|
||
|
|
define HAL_NO_RCIN_THREAD
|
||
|
|
|
||
|
|
define HAL_USE_RTC FALSE
|
||
|
|
define DISABLE_SERIAL_ESC_COMM TRUE
|
||
|
|
define NO_DATAFLASH TRUE
|
||
|
|
|
||
|
|
define DMA_RESERVE_SIZE 0
|
||
|
|
|
||
|
|
define PERIPH_FW TRUE
|
||
|
|
MAIN_STACK 0x800
|
||
|
|
PROCESS_STACK 0x800
|
||
|
|
define HAL_DISABLE_LOOP_DELAY
|
||
|
|
|
||
|
|
define HAL_USE_EMPTY_STORAGE 1
|
||
|
|
define HAL_STORAGE_SIZE 16384
|
||
|
|
|
||
|
|
# enable CAN support
|
||
|
|
PB8 CAN_RX CAN
|
||
|
|
PB9 CAN_TX CAN
|
||
|
|
PB2 GPIO_CAN1_SILENT OUTPUT PUSHPULL LOW GPIO(72)
|
||
|
|
|
||
|
|
# reset for GPS
|
||
|
|
PB6 nGNSS_RESET OUTPUT HIGH GPIO(73)
|
||
|
|
|
||
|
|
define HAL_USE_CAN TRUE
|
||
|
|
define STM32_CAN_USE_CAN1 TRUE
|
||
|
|
|
||
|
|
# make bl baudrate match debug baudrate for easier debugging
|
||
|
|
define BOOTLOADER_BAUDRATE 57600
|
||
|
|
|
||
|
|
# use a small bootloader timeout
|
||
|
|
define HAL_BOOTLOADER_TIMEOUT 1000
|
||
|
|
|
||
|
|
# use LOG_BTN as stay in bootloader, it is active low
|
||
|
|
PA5 STAY_IN_BOOTLOADER INPUT PULLUP
|
||
|
|
define HAL_STAY_IN_BOOTLOADER_VALUE 0
|
||
|
|
|
||
|
|
# reserve 256 bytes for comms between app and bootloader
|
||
|
|
RAM_RESERVE_START 256
|
||
|
|
|
||
|
|
# Add CS pins to ensure they are high in bootloader
|
||
|
|
PB1 MAG_CS CS
|
||
|
|
|
||
|
|
# use DNA
|
||
|
|
define HAL_CAN_DEFAULT_NODE_ID 0
|
||
|
|
|
||
|
|
define CAN_APP_NODE_NAME "org.ardupilot.HitecMosaic"
|