ardupilot/ArduSub/control_circle.cpp

#include "Sub.h"

/*
 * control_circle.pde - init and run calls for circle flight mode
 */

// circle_init - initialise circle controller flight mode
bool Sub::circle_init(bool ignore_checks)
{
    return false; // Not implemented

    //    if (position_ok() || ignore_checks) {
    //        circle_pilot_yaw_override = false;
    //
    //        // initialize speeds and accelerations
    //        pos_control.set_speed_xy(wp_nav.get_speed_xy());
    //        pos_control.set_accel_xy(wp_nav.get_wp_acceleration());
    //        pos_control.set_jerk_xy_to_default();
    //        pos_control.set_speed_z(-g.pilot_velocity_z_max, g.pilot_velocity_z_max);
    //        pos_control.set_accel_z(g.pilot_accel_z);
    //
    //        // initialise circle controller including setting the circle center based on vehicle speed
    //        circle_nav.init();
    //
    //        return true;
    //    }else{
    //        return false;
    //    }
}

// circle_run - runs the circle flight mode
// should be called at 100hz or more
void Sub::circle_run()
{
    float target_yaw_rate = 0;
    float target_climb_rate = 0;

    // initialize speeds and accelerations
    pos_control.set_speed_xy(wp_nav.get_speed_xy());
    pos_control.set_accel_xy(wp_nav.get_wp_acceleration());
    pos_control.set_speed_z(-g.pilot_velocity_z_max, g.pilot_velocity_z_max);
    pos_control.set_accel_z(g.pilot_accel_z);

    // if not auto armed or motor interlock not enabled set throttle to zero and exit immediately
    if (!motors.armed() || !ap.auto_armed || !motors.get_interlock()) {
        // To-Do: add some initialisation of position controllers
        motors.set_desired_spool_state(AP_Motors::DESIRED_SPIN_WHEN_ARMED);
        // Sub vehicles do not stabilize roll/pitch/yaw when disarmed
        attitude_control.set_throttle_out_unstabilized(0,true,g.throttle_filt);

        pos_control.set_alt_target_to_current_alt();
        return;
    }

    // process pilot inputs
    if (!failsafe.manual_control) {
        // get pilot's desired yaw rate
        target_yaw_rate = get_pilot_desired_yaw_rate(channel_yaw->get_control_in());
        if (!is_zero(target_yaw_rate)) {
            circle_pilot_yaw_override = true;
        }

        // get pilot desired climb rate
        target_climb_rate = get_pilot_desired_climb_rate(channel_throttle->get_control_in());

        //        // check for pilot requested take-off
        //        if (ap.land_complete && target_climb_rate > 0) {
        //            // indicate we are taking off
        //            set_land_complete(false);
        //            // clear i term when we're taking off
        //            set_throttle_takeoff();
        //        }
    }

    // set motors to full range
    motors.set_desired_spool_state(AP_Motors::DESIRED_THROTTLE_UNLIMITED);

    // run circle controller
    circle_nav.update();

    // call attitude controller
    if (circle_pilot_yaw_override) {
        attitude_control.input_euler_angle_roll_pitch_euler_rate_yaw(circle_nav.get_roll(), circle_nav.get_pitch(), target_yaw_rate, get_smoothing_gain());
    } else {
        attitude_control.input_euler_angle_roll_pitch_yaw(circle_nav.get_roll(), circle_nav.get_pitch(), circle_nav.get_yaw(),true, get_smoothing_gain());
    }

    // adjust climb rate using rangefinder
    if (rangefinder_alt_ok()) {
        // if rangefinder is ok, use surface tracking
        target_climb_rate = get_surface_tracking_climb_rate(target_climb_rate, pos_control.get_alt_target(), G_Dt);
    }
    // update altitude target and call position controller
    pos_control.set_alt_target_from_climb_rate(target_climb_rate, G_Dt, false);
    pos_control.update_z_controller();
}