mirror of https://github.com/ArduPilot/ardupilot
225 lines
5.6 KiB
Plaintext
225 lines
5.6 KiB
Plaintext
|
# hw definition file for processing by chibios_pins.py
|
||
|
|
# for Aocoda-RC-H743Dual: MPU6000/BMI270x2
|
||
|
|
|
||
|
|
# MCU class and specific type
|
||
|
|
MCU STM32H7xx STM32H743xx
|
||
|
|
|
||
|
|
# board ID for firmware load
|
||
|
|
APJ_BOARD_ID AP_HW_AOCODA-RC-H743DUAL
|
||
|
|
|
||
|
|
# crystal frequency, setup to use external oscillator
|
||
|
|
OSCILLATOR_HZ 8000000
|
||
|
|
|
||
|
|
# flash size
|
||
|
|
FLASH_SIZE_KB 2048
|
||
|
|
|
||
|
|
env OPTIMIZE -Os
|
||
|
|
|
||
|
|
# bootloader takes first sector
|
||
|
|
FLASH_RESERVE_START_KB 128
|
||
|
|
|
||
|
|
# ChibiOS system timer
|
||
|
|
STM32_ST_USE_TIMER 12
|
||
|
|
define CH_CFG_ST_RESOLUTION 16
|
||
|
|
|
||
|
|
# USB setup
|
||
|
|
USB_STRING_MANUFACTURER "Aocoda-RC-H743Dual"
|
||
|
|
|
||
|
|
# Now we define the pins that USB is connected on.
|
||
|
|
PA11 OTG_FS_DM OTG1
|
||
|
|
PA12 OTG_FS_DP OTG1
|
||
|
|
|
||
|
|
# OTG USB VBUS
|
||
|
|
PE2 VBUS INPUT
|
||
|
|
|
||
|
|
# These are the pins for SWD debugging with a STlinkv2 or black-magic probe.
|
||
|
|
PA13 JTMS-SWDIO SWD
|
||
|
|
PA14 JTCK-SWCLK SWD
|
||
|
|
|
||
|
|
# SPI1 for IMU1 (BMI270/MPU6000)
|
||
|
|
PC15 IMU1_CS CS
|
||
|
|
PA5 SPI1_SCK SPI1
|
||
|
|
PA6 SPI1_MISO SPI1
|
||
|
|
PD7 SPI1_MOSI SPI1
|
||
|
|
|
||
|
|
# SPI2 for MAX7456 OSD
|
||
|
|
PB12 MAX7456_CS CS
|
||
|
|
PB13 SPI2_SCK SPI2
|
||
|
|
PB14 SPI2_MISO SPI2
|
||
|
|
PB15 SPI2_MOSI SPI2
|
||
|
|
|
||
|
|
# SPI3 for SPI flash - W25N01GV
|
||
|
|
PD3 FLASH_CS CS
|
||
|
|
PB3 SPI3_SCK SPI3
|
||
|
|
PB4 SPI3_MISO SPI3
|
||
|
|
PB5 SPI3_MOSI SPI3
|
||
|
|
|
||
|
|
# SPI4 for IMU2 (BMI270)
|
||
|
|
PE11 IMU2_CS CS
|
||
|
|
PE12 SPI4_SCK SPI4
|
||
|
|
PE13 SPI4_MISO SPI4
|
||
|
|
PE14 SPI4_MOSI SPI4
|
||
|
|
|
||
|
|
# two I2C bus, order of I2C buses
|
||
|
|
I2C_ORDER I2C2 I2C1
|
||
|
|
|
||
|
|
# I2C1
|
||
|
|
PB6 I2C1_SCL I2C1
|
||
|
|
PB7 I2C1_SDA I2C1
|
||
|
|
|
||
|
|
# I2C2
|
||
|
|
PB10 I2C2_SCL I2C2
|
||
|
|
PB11 I2C2_SDA I2C2
|
||
|
|
|
||
|
|
# ADC for Power
|
||
|
|
PC0 BATT_VOLTAGE_SENS ADC1 SCALE(1)
|
||
|
|
PC1 BATT_CURRENT_SENS ADC1 SCALE(1)
|
||
|
|
PA4 BATT2_VOLTAGE_SENS ADC1 SCALE(1)
|
||
|
|
PA7 BATT2_CURRENT_SENS ADC1 SCALE(1)
|
||
|
|
|
||
|
|
define HAL_BATT_MONITOR_DEFAULT 4
|
||
|
|
define HAL_BATT_VOLT_PIN 10
|
||
|
|
define HAL_BATT_CURR_PIN 11
|
||
|
|
define HAL_BATT2_VOLT_PIN 18
|
||
|
|
define HAL_BATT2_CURR_PIN 7
|
||
|
|
|
||
|
|
define HAL_BATT_VOLT_SCALE 11.0
|
||
|
|
define HAL_BATT_CURR_SCALE 40.0
|
||
|
|
define HAL_BATT2_VOLT_SCALE 11.0
|
||
|
|
|
||
|
|
# ADC for airspeed
|
||
|
|
PC4 PRESSURE_SENS ADC1 SCALE(2)
|
||
|
|
define HAL_DEFAULT_AIRSPEED_PIN 4
|
||
|
|
|
||
|
|
# ADC for rssi
|
||
|
|
PC5 RSSI_ADC ADC1
|
||
|
|
define BOARD_RSSI_ANA_PIN 8
|
||
|
|
|
||
|
|
# Define LEDs
|
||
|
|
# blue LED0 marked as ACT
|
||
|
|
# green LED1 marked as B/E
|
||
|
|
PE3 LED0 OUTPUT LOW GPIO(90) # blue
|
||
|
|
PE4 LED1 OUTPUT LOW GPIO(91) # orange
|
||
|
|
define HAL_GPIO_A_LED_PIN 91
|
||
|
|
define HAL_GPIO_B_LED_PIN 90
|
||
|
|
define HAL_GPIO_LED_OFF 1
|
||
|
|
|
||
|
|
# The normal usage of this ordering is:
|
||
|
|
# 1) SERIAL0: console (primary mavlink, usually USB)
|
||
|
|
# 2) SERIAL1: RC input
|
||
|
|
# 3) SERIAL2: GPS
|
||
|
|
# 4) SERIAL3: VTX
|
||
|
|
# 5) SERIAL4: spare
|
||
|
|
# 6) SERIAL6: ESC Telemetry
|
||
|
|
# 7) SERIAL7: spare
|
||
|
|
# 8) SERIAL8: spare
|
||
|
|
|
||
|
|
# order of UARTs (and USB)
|
||
|
|
SERIAL_ORDER OTG1 USART1 USART2 USART3 UART4 EMPTY USART6 UART7 UART8
|
||
|
|
|
||
|
|
# USART1 (RC input), SERIAL1
|
||
|
|
PA9 USART1_TX USART1
|
||
|
|
PA10 USART1_RX USART1
|
||
|
|
define DEFAULT_SERIAL1_PROTOCOL SerialProtocol_RCIN
|
||
|
|
|
||
|
|
# USART2 (GPS), SERIAL2
|
||
|
|
PD5 USART2_TX USART2
|
||
|
|
PD6 USART2_RX USART2
|
||
|
|
define DEFAULT_SERIAL2_PROTOCOL SerialProtocol_GPS
|
||
|
|
|
||
|
|
# USART3 (VTX), SERIAL3
|
||
|
|
PD8 USART3_TX USART3
|
||
|
|
PD9 USART3_RX USART3
|
||
|
|
define DEFAULT_SERIAL3_PROTOCOL SerialProtocol_DJI_FPV
|
||
|
|
|
||
|
|
# UART4 (Telemetry), SERIAL4
|
||
|
|
PB8 UART4_RX UART4
|
||
|
|
PB9 UART4_TX UART4
|
||
|
|
define DEFAULT_SERIAL4_PROTOCOL SerialProtocol_None
|
||
|
|
|
||
|
|
# USART6 (ESC Telemetry), SERIAL6
|
||
|
|
PC6 USART6_TX USART6 NODMA
|
||
|
|
PC7 USART6_RX USART6 NODMA
|
||
|
|
define DEFAULT_SERIAL6_PROTOCOL SerialProtocol_ESCTelemetry
|
||
|
|
|
||
|
|
# UART7 (spare), SERIA7
|
||
|
|
PE7 UART7_RX UART7
|
||
|
|
PE8 UART7_TX UART7
|
||
|
|
|
||
|
|
# UART8 (Optical Flow), SERIAL8
|
||
|
|
PE0 UART8_RX UART8
|
||
|
|
PE1 UART8_TX UART8
|
||
|
|
|
||
|
|
# Motors
|
||
|
|
PB0 TIM3_CH3 TIM3 PWM(1) GPIO(50) BIDIR //S1
|
||
|
|
PB1 TIM3_CH4 TIM3 PWM(2) GPIO(51) //S2
|
||
|
|
PA0 TIM2_CH1 TIM2 PWM(3) GPIO(52) BIDIR //S3
|
||
|
|
PA1 TIM2_CH2 TIM2 PWM(4) GPIO(53) //S4
|
||
|
|
PA2 TIM5_CH3 TIM5 PWM(5) GPIO(54) BIDIR //S5
|
||
|
|
PA3 TIM5_CH4 TIM5 PWM(6) GPIO(55) //S6
|
||
|
|
PD12 TIM4_CH1 TIM4 PWM(7) GPIO(56) BIDIR //S7
|
||
|
|
PD13 TIM4_CH2 TIM4 PWM(8) GPIO(57) //S8
|
||
|
|
PD14 TIM4_CH3 TIM4 PWM(9) GPIO(58) BIDIR //S9
|
||
|
|
PD15 TIM4_CH4 TIM4 PWM(10) GPIO(59) //S10
|
||
|
|
|
||
|
|
# Servos
|
||
|
|
PE5 TIM15_CH1 TIM15 PWM(11) GPIO(60) NODMA //SE1
|
||
|
|
PE6 TIM15_CH2 TIM15 PWM(12) GPIO(61) NODMA //SE2
|
||
|
|
|
||
|
|
# LED stripe
|
||
|
|
PA8 TIM1_CH1 TIM1 PWM(13) GPIO(62)
|
||
|
|
|
||
|
|
# PWM output for buzzer/Beeper
|
||
|
|
PA15 BUZZER OUTPUT LOW PULLDOWN GPIO(80)
|
||
|
|
define HAL_BUZZER_PIN 80
|
||
|
|
|
||
|
|
# GPIOs for 9V DCDC control (HIGH:on; LOW:off)
|
||
|
|
PD10 PINIO1 OUTPUT GPIO(81) HIGH
|
||
|
|
|
||
|
|
# GPIOs for pinio // not used
|
||
|
|
#PD11 PINIO2 OUTPUT GPIO(82) LOW
|
||
|
|
|
||
|
|
# DMA Priority
|
||
|
|
DMA_PRIORITY S* TIM3* TIM2*
|
||
|
|
DMA_NOSHARE SPI1* SPI4* TIM3* TIM2*
|
||
|
|
|
||
|
|
# use last 2 pages for flash storage
|
||
|
|
# H743 has 16 pages of 128k each
|
||
|
|
STORAGE_FLASH_PAGE 14
|
||
|
|
define HAL_STORAGE_SIZE 32768
|
||
|
|
|
||
|
|
# spi devices
|
||
|
|
SPIDEV mpu6000 SPI1 DEVID1 IMU1_CS MODE3 1*MHZ 8*MHZ
|
||
|
|
SPIDEV bmi270_1 SPI1 DEVID1 IMU1_CS MODE3 10*MHZ 10*MHZ
|
||
|
|
SPIDEV bmi270_2 SPI4 DEVID1 IMU2_CS MODE3 10*MHZ 10*MHZ
|
||
|
|
SPIDEV dataflash SPI3 DEVID1 FLASH_CS MODE3 104*MHZ 104*MHZ
|
||
|
|
SPIDEV osd SPI2 DEVID4 MAX7456_CS MODE0 10*MHZ 10*MHZ
|
||
|
|
|
||
|
|
# two BMI270 or one MPU6000 IMU
|
||
|
|
IMU Invensense SPI:mpu6000 ROTATION_YAW_270
|
||
|
|
IMU BMI270 SPI:bmi270_1 ROTATION_ROLL_180_YAW_90
|
||
|
|
IMU BMI270 SPI:bmi270_2 ROTATION_PITCH_180
|
||
|
|
|
||
|
|
# DPS310 integrated on I2C2 bus, multiple possible choices for external barometer
|
||
|
|
BARO MS56XX I2C:0:0x77
|
||
|
|
BARO DPS310 I2C:0:0x76
|
||
|
|
BARO BMP280 I2C:0:0x76
|
||
|
|
|
||
|
|
# no built-in compass, but probe the i2c bus for all possible
|
||
|
|
# external compass types
|
||
|
|
define ALLOW_ARM_NO_COMPASS
|
||
|
|
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
|
||
|
|
define HAL_I2C_INTERNAL_MASK 1
|
||
|
|
define HAL_COMPASS_AUTO_ROT_DEFAULT 2
|
||
|
|
|
||
|
|
# setup for OSD
|
||
|
|
define OSD_ENABLED 1
|
||
|
|
define HAL_OSD_TYPE_DEFAULT 1
|
||
|
|
ROMFS_WILDCARD libraries/AP_OSD/fonts/font*.bin
|
||
|
|
|
||
|
|
# enable logging to dataflash
|
||
|
|
define HAL_LOGGING_DATAFLASH_ENABLED 1
|
||
|
|
define HAL_LOGGING_DATAFLASH_DRIVER AP_Logger_W25N01GV
|
||
|
|
|
||
|
|
|