ardupilot/libraries/AP_HAL_ChibiOS/hwdef/MatekF405-CAN/hwdef.dat

181 lines
4.0 KiB
Plaintext
Raw Normal View History

# hw definition file for MATEK M9N-F405
# MCU class and specific type
MCU STM32F4xx STM32F405xx
# bootloader starts firmware at 64k
FLASH_RESERVE_START_KB 64
FLASH_SIZE_KB 1024
# store parameters in pages 11 and 12
define STORAGE_FLASH_PAGE 1
define HAL_STORAGE_SIZE 15360
# board ID for firmware load
APJ_BOARD_ID 1014
define STM32_ST_USE_TIMER 5
define CH_CFG_ST_RESOLUTION 32
# crystal frequency
OSCILLATOR_HZ 8000000
# --------------------- LED -----------------------
PA14 LED0 OUTPUT LOW GPIO(90) # blue marked as ACT
PA13 LED1 OUTPUT LOW GPIO(91) # green marked as B/E
define HAL_GPIO_A_LED_PIN 91
define HAL_GPIO_B_LED_PIN 90
define HAL_GPIO_LED_OFF 1
# --------------------- PWM -----------------------
PC6 TIM8_CH1 TIM8 PWM(1) GPIO(50)
PC7 TIM8_CH2 TIM8 PWM(2) GPIO(51)
PC8 TIM8_CH3 TIM8 PWM(3) GPIO(52)
PC9 TIM8_CH4 TIM8 PWM(4) GPIO(53)
PB0 TIM3_CH3 TIM3 PWM(5) GPIO(54)
PB1 TIM3_CH4 TIM3 PWM(6) GPIO(55)
PB6 TIM4_CH1 TIM4 PWM(7) GPIO(56)
PB7 TIM4_CH2 TIM4 PWM(8) GPIO(57)
PA15 TIM2_CH1 TIM2 PWM(9) GPIO(58) # LED pin
define BOARD_PWM_COUNT_DEFAULT 9
define STM32_PWM_USE_ADVANCED TRUE
# Beeper
PA8 TIM1_CH1 TIM1 GPIO(32) ALARM
# --------------------- SPI1 -----------------------
PA5 SPI1_SCK SPI1
PA6 SPI1_MISO SPI1
PA7 SPI1_MOSI SPI1
PA4 MPU_CS CS
# --------------------- SPI2 -----------------------
PB13 SPI2_SCK SPI2
PB14 SPI2_MISO SPI2
PB15 SPI2_MOSI SPI2
PB12 MAG_CS CS
# --------------------- SPI3 -----------------------
PB3 SPI3_SCK SPI3
PB4 SPI3_MISO SPI3
PB5 SPI3_MOSI SPI3
PC14 SDCARD_CS CS
# -------------------- I2C bus --------------------
I2C_ORDER I2C2
PB10 I2C2_SCL I2C2
PB11 I2C2_SDA I2C2
define HAL_I2C_INTERNAL_MASK 0
# -------------------- CAN bus ---------------------
PB8 CAN1_RX CAN1
PB9 CAN1_TX CAN1
PC13 GPIO_CAN1_SILENT OUTPUT PUSHPULL SPEED_LOW LOW GPIO(70)
# --------------------- UARTs ---------------------------
SERIAL_ORDER OTG1 USART1 USART3 UART4 UART5 USART2
PA11 OTG_FS_DM OTG1
PA12 OTG_FS_DP OTG1
# USART1
PA9 USART1_TX USART1
PA10 USART1_RX USART1
# USART2
# alternative using USART2
PA2 USART2_TX USART2 NODMA
PA3 USART2_RX USART2 NODMA ALT(1)
# default to timer for RC input
PA3 TIM9_CH2 TIM9 RCININT FLOAT LOW
# USART3
PC10 USART3_TX USART3
PC11 USART3_RX USART3
# UART4, for GPS
PA0 UART4_TX UART4
PA1 UART4_RX UART4
# USART5
PC12 UART5_TX UART5
PD2 UART5_RX UART5
# --------------------- ICM20602 -----------------------
SPIDEV icm20602 SPI1 DEVID1 MPU_CS MODE3 1*MHZ 4*MHZ
IMU Invensense SPI:icm20602 ROTATION_ROLL_180_YAW_90
define HAL_DEFAULT_INS_FAST_SAMPLE 1
# --------------------- RM3100 -------------------------
SPIDEV rm3100 SPI2 DEVID1 MAG_CS MODE0 1*MHZ 1*MHZ
COMPASS RM3100 SPI:rm3100 false ROTATION_PITCH_180
# also probe for external compasses
define ALLOW_ARM_NO_COMPASS
define HAL_PROBE_EXTERNAL_I2C_COMPASSES
# --------------------- SD ----------------------------
SPIDEV sdcard SPI3 DEVID3 SDCARD_CS MODE0 400*KHZ 25*MHZ
define HAL_OS_FATFS_IO 1
define HAL_BOARD_LOG_DIRECTORY "/APM/LOGS"
define HAL_BOARD_TERRAIN_DIRECTORY "/APM/TERRAIN"
# --------------------- DPS310 ------------------------
BARO DPS280 I2C:0:0x76
# --------------------- ADC ---------------------------
PC0 BATT_VOLTAGE_SENS ADC1 SCALE(1)
PC1 BATT_CURRENT_SENS ADC1 SCALE(1)
PC2 RSSI_ADC_PIN ADC1 SCALE(1)
PC3 PRESSURE_SENS ADC1 SCALE(1)
PC5 BATT2_VOLTAGE_SENS ADC1 SCALE(1)
define HAL_BATT_MONITOR_DEFAULT 4
define HAL_BATT2_MONITOR_DEFAULT 4
define HAL_BATT_VOLT_PIN 10
define HAL_BATT_VOLT_SCALE 21.0
define HAL_BATT_CURR_PIN 11
define HAL_BATT_CURR_SCALE 40.0
define BOARD_RSSI_ANA_PIN 12
define HAL_DEFAULT_AIRSPEED_PIN 13
define HAL_BATT2_VOLT_PIN 15
define HAL_BATT2_VOLT_SCALE 11.0
# --------------------- save flash ----------------------
define HAL_MINIMIZE_FEATURES 1
define HAL_BATTMON_SMBUS_ENABLE 0
define HAL_BATTMON_FUEL_ENABLE 0
define HAL_PARACHUTE_ENABLED 0
define HAL_SPRAYER_ENABLED 0
define HAL_WITH_DSP FALSE
# reduce max size of embedded params for apj_tool.py
define AP_PARAM_MAX_EMBEDDED_PARAM 1024